Question about Cars & Trucks
The problem could be several things, including the blower motor, relay, resistor, or fan switch.
When it is not working, someone would need to check for power at the blower motor and the other components.
Posted on Apr 20, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
in my 2004 grand caravan it's behind the glove box and left of the blower motor. disconnect the wires first then remove the 2 screws to pull out the resistor unit. First make sure you have removed the negative of your batterie. I had the same pm that prevented the blower motor to operate in any speed. I hope this will help
Posted on Dec 25, 2008
These vehicles seem to have a problematic short, my grandfather has the same vehicle with the same problem, i found the short under the carpet on the driver side of the vehicle, under the gas pedal, sometimes wires can crack and break.
Posted on Jun 01, 2009
OK So, I have had to replace the blower resistor twice and its still has failed. Now its time to replace the blower motor. I have the Haynes manual for this vehicle but it seems to miss some important steps. Here's what I did, I hope it helps you. This job is given 3.5 hours on the shop book and believe me, its not a wonder why.
Tools that I used
- standard screwdrivers 6" with 1/4 blade and 8" with 1/2" blade
- 1/4 inch ratchet with 2" and 1" extensions
- 8mm socket
- 10 mm wrench
- Phillips S2
- drill with attachment for screwdrivers ( I have tendonitis)
- gooseneck extension (plastic / flexible)
Here are the instructions from the Haynes book with my comments and pictures.
One note is that the picture in section 3-8, fig 10-10 is upside down. The Actuator motor is on the bottom of the unit, looks
like a black deck of cards with a wire going to it. Wires at clipped to the housing.
2001 and later models
Step 8 - Disconnect battery negative cable - Wrench 10mm (1/2inch)
Step 9 - Partially remove instrument panel.... - remove glove compartment to access the blower and evap area. Two clips on
either side, unsnap hinges. ( remember to empty the box)
Step 10 - Disconnect pigtail from blower motor resistor. Green/Black wires
Step 11 - Remove 2 screws to remove actuator. (8mm socket) Remove wire from clips and pull down to remove the acuator. This
will buy you about 1/2 of extra space. Before you do all this, remove the side carpet trim which allows you to pull back the
carpet and the silencer padding. This will allow for some more room to pull the housing down and believe me, you'll need it!
Step 12 - Remove 2 more screws on the air intake and lower housing. I had three screws, you should see them through the
Step 13 - Remove the 3 screws at the lower intake and lower evap housing.
Step 14 - Push rubber grommet through hole in lower housing. Use large blade screwdriver.
Step 15 - Remove lower intake housing from evap housing.
This is where it gets tricky.
You can remove the lower intake housing but you need to pry it out from the recirculation door.
The bottom of the unit where the actuator was has a round spindle that clips into place with the three plastic clips.
Lightly pry the lower clips and then also pry through the hole at the connection point. Picture below.
Once you pry it will release.
You will have to jiggle this loose but it will eventually come off.
with mine the recirc door POPPED out of its top rest. I had to make sure on how to get it into this spot as it doesn't stay in this spot.
Step 16 - Push wires through the hole if you haven't done so already.
Step 17 - Move recirc door about to help you reach the three screws that hold down the motor assembly.
Step 18 - GENTLY flex the door to remove the blower motor and wheel. I moved the motor 180 to help get into a better position.
Install is reverse. Need to make sure that the recirc door moves relatively easily. The calibration below will make sure all is set properly. If it doesnt pass you'll have to recheck the position of the recirc door top spindle and cavity line up.
Step 19 - Not in the book
18. Perform the heater-NC control calibration procedure:
a. Turn the ignition switch to the ON position.
b. Simultaneously depress and hold the Power and Recirculation buttons on the heater-A/C control for at least five seconds.
The manual heater-A/C control Delay Light Emitting Diode (LED) and Recirculation LED, or the Automatic Temperature Control
(ATC) heater-A/C control Delay and Recirculation graphics will begin to flash when the calibration procedure has begun.
c. The calibration procedure should take less than three minutes to complete for the manual system, and less than twenty
seconds for the ATC system. When the LED's or graphics stop flashing, the calibration procedure is complete.
d. If the LED's or graphics continue to flash beyond the time stated above, it indicates that the heater-A/C control system
has detected a failure and a Diagnostic Trouble Code (DTC) has been set. Use the DRBIII(R) scan tool and the appropriate
diagnostic information for further diagnosis.
Posted on Nov 09, 2009
Remove the cover plate on the passenger side of the heater box, 3-4 screws.
Unplug the motor assembly, remove 3-4 more screws that hold the motor in place and pull it down from its position. Get an aftermarket motor and installed it in the original housing with the original squirrel cage.
Installation is the reverse of removal.
Posted on Nov 23, 2009
Check owners manual for location of heater blower motor front,check with a test light,if it's good locate blower motor under glove box and test the two wires for power when switch is turned on,if power is present motor needs changed.if no power check blower motor resister.
Posted on Nov 23, 2009
Tips for a great answer:
Apr 08, 2013 | 2001 Dodge Grand Caravan
Dec 19, 2010 | 2001 Dodge Grand Caravan
May 17, 2010 | 2001 Dodge Grand Caravan
Dec 23, 2009 | 1996 Dodge Caravan
Oct 19, 2009 | 2001 Dodge Caravan
Jul 01, 2009 | 2003 Dodge Caravan
Jun 01, 2009 | 1992 Dodge Caravan
Dec 23, 2008 | 2001 Dodge Grand Caravan
75 people viewed this question
Usually answered in minutes!