Question about 2005 GMC Sierra 2500HD 4WD

Open Question

How to remove rear axle in a 2005 gmc sierra 2500

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2003 gmc sierra duramax 2500

Problem with Diesel Fuel System. Gmc 2002 duramax 2500 HD 4x4 will start 

Posted on May 15, 2009

Ad
  • 375 Answers

SOURCE: 2007 gmc sierra 2500 IAT sensor

Well, the IAT (Intake Air Temperature) sensor is located on the air intake duct between the filter and the throttle body (Assuming you have the 6L motor). The wires are easily visible at the plug that connects the sensor to the wiring harness. That's the easiest place to access them.

Posted on May 18, 2008

Rayvin1943
  • 97 Answers

SOURCE: 1994 gmc rear axle removal how to

-Remove tire and brake drum
-put drain pan under axle housing
-remove rear axle housing cover (10 or 12 bolts)
-turn gear untiil the bolt for cross shaft shows and remov e the bolt
-remove the cross shaft.
-push axle in until you can remove "U" clip from axle and axle will pull out,
Remove seal, you need a pulller to remove axle brg.

Posted on Jul 26, 2009

  • 198 Answers

SOURCE: 2004 gmc sierra rear differential

remove cover.take off back wheels and calipers (or drums).turn differential to where you see small bolt/pin (5/16) horizontally (same direction as axles)on right side of differential.remove bolt/pin.A large pin (about 5"long 3/4"diameter) should slide out differential with ease ( you may have to tap one side of the large pin).turn differential to completely remove large pin.turn differential so you can see in the view window.push each axles in (they'll go in about 1 1/2"each) You may hear one of the axle C-clips fall.If not use a small telescoping magnet to remove the C-clips from the axles through the differential window.pull each axle out about 10"so they are out of the diff.Now remove the cap bolts(4-5/8"bolts) and remove the caps(mark the caps so they go in excactly the way they came out.be careful the diff might fall out.If not you may have to use a long bar or 2x4 to wedge and pry the differential out. Have a basket/crate w/rags in it to catch the diff.TIP:If you are removing the ring gear from the diff, the bolts are left handed bolts meaning you have to turn them clockwise to loosen and counter clockwise to tighten ; )

Posted on Sep 15, 2009

Testimonial: "thank you helped ALOT perfect instructions "

  • 1 Answer

SOURCE: need picture diagram of rear brake shoe

I need pictures for 1998 gmc sierra k2500 rear bkake shoes.

Posted on Jan 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace drivers side rear wheel bearing on 2005 gmc sierra with drum brakes?


not very much info. 1/2 ton? 2wd? If it is a standard pickup there are "C" clips that hold the axles in. You will have to remove the 3rd member cover and remove the clip. This is after you have removed the wheel and brake drum. The axle will slide out and the bearing will remain in the axle housing.Messy job. Take it to your mechanic.

Dec 06, 2014 | GMC Sierra 1500 Cars & Trucks

1 Answer

How do I get the axle out 2004 gmc sierra rearend ?


Other than watch a You Tube Video, on any similar
axle housing ?

Remove the rear cover,bolt,cross shaft pin,push
axles in,remove c-clip & pull axle out !!

Oct 04, 2014 | 2004 GMC Sierra

1 Answer

2005 GMC 4x4 HD 2500 6.0 eng. rear axel seal


SEAL COULD BE LEAKING CAUSE YOU DIDNT LUBRICATE THE SEAL LIPS WITH PETROLEUM JELLY TO HELP THE THE SEAL LIP SEAL OR YOU DAMAGE THE SEAL WHILE DRIVING IT IN.AXLE FLANGE NUTS TORQUE IS 58 FT LBS THE AXLE HUB NUT TORQUE IS 177 FT LBS.

Jul 14, 2010 | 2005 GMC Sierra 2500HD 4WD

1 Answer

I have a GMC Sierra 2500 with 4_wheel drive. I


Not sure if this year was a sealed hub like newer ones bt the process is the same. You need to take off the brake caliper, take off the caliber mount to the axle, then the rotor should come off. May be able to remove the stud now but if not, will probably have to remove the hub. It is bolted on to the axle with 4 bolts usually. Need to pop the cap off of the outside of the hub to access the nut holding the front axle shaft to the hub. It is splined shaft that is not pressed on. By tapping the end (lightly on the threaded end) and pulling out the hub will usually release it. Good luck!

May 25, 2010 | 1996 GMC Sierra

1 Answer

Need detailed manual or assistance in replacing left rear axle seal and bearing on 2005 GMC Sierra pickup with 5.3L engine and a 324 rear end


You'll need to remove the rear end cover, remove the pin in the center pumpkin, push axle toward the center of vehicle and remove the axle clip, pull out axle. You may need a bearing puller to remove bearing.

Mar 04, 2010 | 2005 GMC Sierra

1 Answer

How to replace rear brakes in 2005GMC Sierra?


jack up truck support it remove tire you should see the caliper,on the back side you will see two small bolts lossen the bolts remove it might require some prying support the caliper,check the rotor if has grooves in it it should be turned. use a c clamp to force the piston back in the caliper be careful of the rubber seal put the new pads on reinstall the caliper tighten the bolts start the truck pump the brakes a few times go back check for leaks if none put tire back on remove support lower to ground test drive

Nov 02, 2009 | 2005 GMC Sierra

1 Answer

Have a 95 seirra 2500 pickup rear axle seal and bearing out, do i need to go into the differential to pull axle?


Depends on what kind of axle you have. Is it a semi-floating axle, or a full-floating type?

Oct 09, 2009 | 1995 GMC Sierra

2 Answers

How to remove the rear rotors on a gmc 2002 2500 hd extra cab 4x4


The rotors are one with the hub.s, So, you need to pull the axles , hub bearings. Good Luck

Sep 18, 2009 | 2002 GMC Sierra 2500HD

2 Answers

Replaceing hub assembly on 2004 gmc


Thats it ,oh and a hammer to knock it out of the knuckle.Some guys tighten the axle nut back up with a torque wrench.

Nov 29, 2008 | 2005 GMC Sierra 2500HD 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...