Question about 1981 Ford F 100

Open Question

Clutch linkage bushing for 1981 ford f100

Clutch pedal sticks half way up after pushing down

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
aliensanity
  • 24 Answers

SOURCE: clutch pedal not returning to position

Under the dash look to see if there is a spring attached to the petal or maybe under the hood. Or you might have something getting in the was of the petal arm. Good Luck and PEACE

Posted on Jun 13, 2008

Ad
co7196
  • 3433 Answers

SOURCE: clutch sticks in transmission won't go into gear

Clutch is out of adjustment

Posted on Oct 06, 2009

ZJLimited
  • 17970 Answers

SOURCE: changing a water pump on a 1981 ford f100 pick-up

Ford Pick-Ups/Bronco 1976-1986 Repair Guide Water Pump - REMOVAL & INSTALLATION

6-300 Engines

  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Disconnect the lower radiator hose from the water pump.
  2. Remove the drive belt, fan, fan spacer, fan shroud, if so equipped, and water pump pulley.
  3. Remove the alternator pivot arm from the pump.
  4. Disconnect the heater hose at the water pump.
  5. Remove the water pump.
  6. Before installing the old water pump, clean the gasket mounting surfaces on the pump and on the cylinder block. If a new water pump is being installed, remove the heater hose fitting from the old pump and install it on the new one. Coat the new gaskets with sealer on both sides and install the water pump in the reverse order of removal. Torque the mounting bolts to 14-18 ft. lbs.

V6-3.8L Engines
See Figures 1 and 2

5ee356b.jpg

Fig. 1: V6 water pump installation

e5820a7.jpg

Fig. 2: V6 water pump bolt torque sequence
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the air cleaner.
  2. Remove the bolts securing the fan shroud to the radiator, if so equipped, and position the shroud over the fan.
  3. Disconnect the lower radiator hose, heater hose and by-pass hose at the water pump. Remove the drive belts, fan, fan spacer and pulley. Remove the fan shroud, if so equipped.
  4. Loosen the alternator pivot bolt and the bolt attaching the alternator adjusting arm to the water pump. Remove the power steering pump bracket from the water pump and position it out of the way.
  5. If necessary, remove the air conditioner compressor and bracket. The refrigerant lines should remain connected.
  6. Remove the bolts securing the water pump to the timing chain cover and remove the water pump.
  7. Thoroughly clean the mounting surfaces of all gasket material.
  8. Install the water pump in the reverse order of removal, using a new gasket. Torque the bolts to 15-22 ft. lbs. in the sequence shown.


8-360, 390
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the bolts securing the fan shroud to the radiator, if so equipped, and position the shroud over the fan.
  2. Disconnect the lower radiator hose, heater hose and by-pass hose at the water pump. Remove the drive belts, fan, fan spacer and pulley. Remove the fan shroud, if so equipped.
  3. Loosen the alternator pivot bolt and the bolt attaching the alternator adjusting arm to the water pump. Remove the power steering pump bracket from the water pump and position it out of the way.
  4. If necessary, remove the air conditioner compressor and bracket. The refrigerant lines should remain connected.
  5. Remove the bolts securing the water pump to the timing chain cover and remove the water pump.
  6. Install the water pump in the reverse order of removal, using a new gasket. Torque the bolts to 20-25 ft. lbs.

8-351M, 400, 460
  1. Disconnect the battery ground.
  2. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by the ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the bolts securing the fan shroud to the radiator, if so equipped, and position the shroud over the fan.
  2. Remove the fan assembly.
  3. Remove the fan shroud.
  4. Remove the accessory drive belts and water pump pulley.
  5. Remove the alternator and brackets.
  6. Remove the compressor and bracket and lay it aside. DO NOT disconnect the refrigerant lines!
  7. Remove the power steering pump and brackets. Lay it aside. DO NOT disconnect the fluid lines!
  8. Disconnect the heater hose and lower radiator hose from the pump.
  9. Remove the bolts securing the water pump to the engine and lift off the water pump.
  10. Clean all gasket mounting surfaces thoroughly.
To install:
  1. Install the water pump in the reverse order of removal, using a new gasket coated with sealer. Torque the bolts to 12-18 ft. lbs.
  2. Install all remaining parts in reverse order. Fill the cooling system, start the engine and check for leaks.

continue...

Posted on Mar 25, 2010

emissionwiz
  • 76846 Answers

SOURCE: the clutch pedal sticks down when trying to engage

YOU DO NEED A NEW DISC AND MOST LIKELY A MASTER AND SLAVE HYDRAULIC CLUTCH CYLINDERS, THE STICKING MAY BE DUE TO OVER TRAVEL DUE TO THE WORN OUT DISK.

Posted on May 11, 2010

  • 123 Answers

SOURCE: I am unable to put my 2001 Ford Escape xls into

that is your clutch pump/cable in not functioning. u need to check the fluid level (if your car using hydraulic clutch) or your clutch cable broke...

Posted on Nov 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why dose the clutch pedal stick down on my peugeot ?


The linkage between the pedal and the clutch throwout bearing needs attention - the return spring appears to not have been reinstalled correctly, or has broken.

Jul 29, 2014 | Peugeot 405 Cars & Trucks

1 Answer

Cluch is out on 1981 ford f100


Good , now service the clutch , put new spring and pads , re-install .

Jan 23, 2013 | 1981 Ford F 100

1 Answer

Clutch sticking will not go into first


Ok it looks like there is no problem with the clutch or tranmission. You problem is that the clutch pedal is stiff and sticking to the floor. This sometimes happens when vehicles sit for extended periods of time. It might free up by working back and forth by hand. Have the vehicle off and the parking brake applied and push the clutch pedal up and down with your hand, It might stick to the floor and you may have to pull it off the floor a few times. You can also get some spray lubricant from your local canadian tire or auto parts store. open the hood and have someone move the clutch pedal up and down and spray the moving parts. It might take a few times to free up the stiff linkage but it will work :)

Mar 07, 2011 | Nissan Se R Cars & Trucks

1 Answer

Cluth pedal feels the same only clutch wont disengage on a 92 dodge stealth


i had this problem for awhile and found out it was the clutch pedal assembly... push ur clutch pedal down a few times then reach down and pull up on it, give it a good tug! if it moves up half an inch or more, your clutch peddal ***. needs a rebuild. jus a few bushings, u can get em from sheptrans. they even have clutch pedal

Dec 20, 2010 | 1992 Dodge Stealth

1 Answer

Will a 1976 ford f100 front suspention fit under a 1976 ford f250


Yes and No

Yes if you the knowledge of welding gussets for the larger bushings it takes.
No if you do not have a welder and the materials to make your own new parts to attach

May 17, 2010 | 1981 Ford F 100

1 Answer

Ned to now wat the firing order for dist cop shood be for a 1987 ford f100 pick-up truck 300sixcylender stick shift model#333


The F100 ended in 1983, so there is some confusion on your 1987 Ford F100. The F150 started in 1983 and was available in 1987, but not the F100. You have this listed under the 1981 Ford F100 category.
The 300 CID = 4.9L In-Line (Straight) 6-Cylinder.
In order to best answer your question I have included both the 1981 F100 4.9L and 1987 F150 4.9L below. The only difference is with the Distributor Cap Configuration and Connections.

For the 1981 F100 300cid=4.9L:
Firing order:
1-5-3-6-2-4
Cylinders:
(back)
...6
...5
...4
...3
...2
...1
(front)
Distributor:
...(back)
.........4..[.]-clip
2
...................1
6
................5
[.]....3

For the 1987 F150 300cid=4.9L:
Firing Order:
1-5-3-6-2-4
Cylinders:
(back)
..6
..5
..4
..3
..2
..1
(front)
Distributor:
.......(back)
.................4
.....2
[.]
.......................1
..6
.........................[.]-clip
....................5
.......3
.........(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

May 07, 2010 | 1981 Ford F 100

2 Answers

Clutch pedal fails to return fully after depressing.


If your truck has a hydraulic clutch it will have an extra reservoir, near the brake fluid reservoir, and the clutch side uses brake fluid also. Your problem I think, is that you are low on fluid. That can cause the problem you describe. Look for this extra reservoir and check it for low fluid, it may be dirty but should have full / low mark on the side.

Feb 11, 2010 | 1981 Ford F 100

1 Answer

Ford f 150 1988 clutch has no spring and lays on the floor


Get your face near the floorboard, and look at the clutch pedal. Now look at what is connected to it that runs through the body and down toward the tranny. If this rod moves in and out of its hole when you move pedal...

...then stick your head under vehicle and find where this rod comes out. There is another rod hooked to it that actuates the clutch. One of these has likely fallen off, due to a worn rod and bushing. Sometimes they are so worn, they must be replaced. If you catch it in time, you can replace the plastic bushing and/or just snap it back together. Sounds like your linkage has come apart between pedal and clutch. Rod has some adjustment, but only to a point.

Mar 20, 2009 | 1996 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...