Question about 1998 Chrysler Cirrus

Open Question

1998 Chrysler Cirrus Strut Noise - 1998 Chrysler Cirrus

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 571 Answers

SOURCE: What kind of noise would the vibration damper

Sounds more like busted wheel alignment. Does the noice disappear when speeding more (up to 65-70)?

Posted on Nov 04, 2009

  • 880 Answers

SOURCE: where is thermostat in a 1995 chrysler cirrus LX

A tee is located to the right hand side of the intake manifold, on top you should see the coolant system cap, its silver in color and is about 2-3 inches in diameter. This tee is the thermostat housing, it goes to your radiator and engine block, remove it from the block and you should see the thermostat. Remember when replacing the thermostat, the spring side goes into the block! 2.0L and 2.4L it is under where the upper rad hose hooks to the engine. 2.5L it is under where the lower rad hose hooks to the engine.

Posted on Dec 29, 2009

  • 306 Answers

SOURCE: can't get sunrooff to close

Are the fuses good? With the car off and the interior light on, if you try to operate sunroof, does the light dim? If yes, motor is trying to work but stuck. If light stays the same then motor not getting power. Fuses, wiring, bad switch, loose connection. Have to play detective.
There's a small possibility that mechanical cables or pulleys broken stuck, or worn out. Sunroofs look simple but they are very complicated!

Posted on Mar 10, 2010

duane_wong
  • 6826 Answers

SOURCE: How do I compress the front strut enough to get

One needs a special tool called a 'spring compressor' to compress the front strut spring enough to remove the nut on the strut. Very dangerous without the tool. Must use the spring compressor to service the strut assembly, or get a loaded strut/spring assembly to replace old strut assembly.

Good luck on this.

Posted on Oct 28, 2010

ZJLimited
  • 17970 Answers

SOURCE: how do i program new remote keyless entry for my

No way, this keyless entry remote (for 1997-2001 Chrysler CIRRUS Keyless entry remote) must be programmed to your vehicle before it will work. This can only be done at a professional automotive locksmith shop. If you are unable to find a locksmith, the dealership will be able to program it for you instead. There are no programming instructions available for this keyless entry remote. It can only be done at the locksmith or dealer with special equipment.

zjlimited_0.jpeg


Hope this helps (remember to rate this answer).

Posted on Jan 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car was making a grinding noise in front and then my tire blew up. Was told my be a split tire rod or split sway bar


i would say that the wheel bearing is gone and the wheel hit the strut housing thus cutting tire

Jan 21, 2012 | 2000 Chrysler Cirrus

2 Answers

The piece that holds up the front passenger wheel (i believe its called a strut), is bent or broken, would u happen to kno how much that would approx. cost? its a 2002 chrysler sebring


$61 at autozone:
http://www.autozone.com/autozone/parts/Gabriel-Ultra-Shock-Strut-Front/2002-Chrysler-Sebring/_/N-jh9olZ8oxxw?counter=0&filterByKeyWord=strut&fromString=search&itemIdentifier=602085_6880_2457_4299

The strut must be compressed for mounting. Labor is approximately 2 hours. Not sure what labor costs in your area or if your shop will allow you to bring strut or require you to buy from them.

May 19, 2011 | 1999 Chrysler Cirrus

1 Answer

How do I compress the front strut enough to get the nut on when replacing a 1997 Chrysler cirrus front strut?


One needs a special tool called a 'spring compressor' to compress the front strut spring enough to remove the nut on the strut. Very dangerous without the tool. Must use the spring compressor to service the strut assembly, or get a loaded strut/spring assembly to replace old strut assembly.

Good luck on this.

Oct 28, 2010 | 1997 Chrysler Cirrus

1 Answer

I cannot close the sunroof of my 1998 Chrysler Cirrus and I've changed the fuse already. Please help with any suggestions.


maybe the motor is burn up check it with a voltmeter make sure getting power and listen see if it is making a noise like trying but not enough power also check the motors ground wire make sure clean good contacts

Sep 11, 2010 | 1998 Chrysler Cirrus

1 Answer

How do i change a lower right control arm on a 1995 chrysler cirrus?


undo the ball joint/remove sway bar link nut at arm/ remove bolt[s] from arm to frame. it has a strut so no worries about any springs. pretty easy really

Apr 27, 2010 | 1995 Chrysler Cirrus

1 Answer

Disable alarm on 98 cirrus


how do i disarm an alarm on a 1998 chrysler cirrus?

Oct 23, 2009 | 1998 Chrysler Cirrus

1 Answer

Back struts.


Should have to take off the bolt on the bottom of the strut, and the strut mounts on the top. Most likely get them through the trunk.

Mar 18, 2009 | 1995 Chrysler Cirrus

Not finding what you are looking for?
1998 Chrysler Cirrus Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...