Question about 1992 Lincoln Town Car

1 Answer

Hood release broke

Back fires slow acceleration

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Lincoln Master
  • 880 Answers

THE HOOD RELEASE CAN BE ACCESS FROM UNDER THE CAR . GET THE HOOD OPEN REPLACE THE HOOD RELEASE CABLE AND GET A TUNE UP

Posted on Nov 16, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to open the hood on 05 mitsubishi lancer es after hood release cable broke on engine bay side.


Cut the outer hood release cable sheath (under the dash) back to expose the inner wire cable, then using a pair of locking pliers (Vise Grips) pull on the inner release cable while another person pushes down over the latch area of the hood to relieve pressure on the latch and make it easier to open, the hook is released lubricate the hood latch and hood latch striker with white Lithium Grease (AKA "Lubriplate")

Mar 14, 2017 | 2005 Mitsubishi Lancer

1 Answer

Vibration in steering wheel that will disappear after slowing down and then accelerating in 2002 Subaru outback


Drive Line Universial Joint
Belt Broke in a Tire

Make sure your Tire Pressure is correct

Apr 10, 2013 | 2002 Subaru Outback

1 Answer

Back fires thru carb when excellerating but lopes when u take off manual trans


do you hear a pop pop poping under heavy acceleration or just one big back fireing when first accelerating? it could be an intake valve pop pop poping,and electrical,on the big bafireing under lite to med load. A cracked,or worn cap and rotor,weak coil wire,dirty carbruator,faulty accelerator pump in carb bad vacumn advance !slow ignition timing. BAD points and condenser if equiped on older model with carb.

Sep 01, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

My hood release cable is broke how do i open the


i assume it broke at the latch? if you lay on the ground you might be able to get at the latch. if it broke at the handle grab the wire with pliers

Jul 24, 2010 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Hi! I was driving my Land Rover freelander 2.0D. I felt that the clutch was little bit slow when I was pushing it I contiuned driving and was accelerating to third gear. But since I would make a right turn...


One of three things 1) All the hydraulic fluid was suddenly lost from your clutch - check the fluid reservoir level under the hood on the fire wall bulk head 2) the clutch lever or release bearing has broken 3) the clutch diaphragm spring on the clutch plate has broken These last two can be checked by waggling the end of the clutch lever but any repair requires the transmission to be removed. Might be a good time to change the clutch and bearing while you are it.

Jun 29, 2010 | Cars & Trucks

1 Answer

The hood release handle is stuck out and won't spring back on my 99 ford escort. The hood is closed and latched. Any help would be appreciated


you probably have to open up the hood latch assembly and replace the sring. sounds like it broke. or maybe the cable. can you push it back in?

Feb 25, 2010 | 1997 Ford Explorer AWD

1 Answer

Idle ok,slow acceleration fine,accelerating quickly miss-fires


Sounds like you have a leaking cylinder head gasket

Jul 18, 2017 | 1992 Ford Escort 4 Door

1 Answer

Hood release broke inside car. How do you release hood?


see if you can grab the broken cable end with a pair of locking pliars (vise grips) and pull

Apr 18, 2009 | 1992 Dodge Spirit

1 Answer

95 plymouth voyager hood release broke


get a pair of vice grips and use them to get a hold of what remains of the release cable and pull,,,after success,,,get a new cable installed.

Jan 16, 2009 | 1995 Plymouth Voyager

Not finding what you are looking for?
1992 Lincoln Town Car Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...