Question about 2009 Chevrolet Impala

1 Answer

2009 impala dtc b001b

Dtc b001b, should i replace the passenger side pretensioner

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,585 Answers

Could be the problem. You would have to remove the seat belt harness. But I would check plugs and continuity of the wires first. The plug for the belt is in the column at the side, the plug for the tensioner(air bag module) is under the console.

Posted on Aug 20, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: passenger side mirror

If you need to replace the entire mirror - it's a little involved. First you need to take the upper extension panel off from behind the mirror (black triangle) - just pull it of starting at the top. It will snap back on later. Next - remove the different screws holding the door panel in place (not the ones behind the mirror yet!) One is under the handle (pull it out and pull out the filler panel - small plastic thing that has a hole to pry it out). Then take off the rear red light - also pops off - and remove that screw. Finally - pick up the rubber filler where your fingers pull the door shut and remove these torx bolts.

Now is the tricky part. Snapp off the entire interior panel. It will pop off - but very difficult. It will sound like it is breaking! Start at the outer bottom corner - and use a door panel remover tool - check Amazon or E-bay - to keep from breaking things. Pull it out from all around the bottom and sides and then lift it up over the door lock. It good to have a friend help here. The panel will still be held on by a cable - that is your door release - leave it alone and let the panel hang by it (or better, put a box under it to rest on).

Now...remove the three bolts holding the mirror on - have a friend help hold the mirror while you do this or it will scratch your new car! Since the inner panel is off - you can also disonnect the mirror plus and remove it. It sounds silly - but the only reason to remove the door panel is to unplug it!

Get you new mirror and reverse the steps.

If you are just replacing the glass (non-heated) - get a replacement from the dealer. Adjust the mirror all the way to the inside and reach behind and pop it off. CAREFUL - put tape over the entire glass as it will likely break even more! Remove your connectors if heated - and replace (and reconnect) with your new glass. It just pops back on!

Replacing glass is easy - just be careful of cheap imitations on e-abay). And never use cheap flat glass on the passenger side! The DOT has special requirements for mirror glass - buy it from gmpartsdirect.com or your local dealer.

kb

Posted on Jan 08, 2009

  • 1986 Answers

SOURCE: replace passenger side mirror on 2008 Impala

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

  • 18 Answers

SOURCE: Need to replace tail light bulb passenger side on

Here is some great CAR solution by Some FIXYA EXPERT.
Get any kinds of CAR solution from bellow.

18

Posted on Dec 18, 2009

kken123
  • 126 Answers

SOURCE: 2009 impala heated seat on passenger side does not

You need to replace the heating pad in the seat it is grounded out.

Posted on Jan 21, 2011

pcdj64
  • 1150 Answers

SOURCE: passenger side back door lock not working on 2009 Impala

could be a bad actuator in the door.

Posted on Sep 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 ford f-350 passenger air bag flashes 1-7 code than stays on when truck is started.What does the code mean and can the code be reset without tearing air bag out of truck?


If a SRS fault exists, the RCM sends a message to instrument cluster module to flash a coded sequence which is called a lamp flash code (LFC) on the air bag warning indicator. Each LFC is flashed 3 times after which the air bag indictor will remain lit for the remainder of the key-on cycle. In addition to the self-test at start up, the RCM continuously monitors all of its external and internal circuitry for faults.
While the LFCs are an indication of a general concern in the supplemental restraint system (SRS), the DTCs are more specific. The DTCs can be retrieved from the RCM with a scan tool via the DLC.


DTC a c LFC b Description Action To Take - Continuous Lamp The Air Bag Warning Indicator is Illuminated Continuously (RCM Disconnected or Inoperative, Loss of Battery Feed or Loss of Signal Ground) Go To Pinpoint Test A . B1048 c - Passenger Side Air Bag Cross Link to Another Firing Loop Go To Pinpoint Test B . B1049 c - Passenger Seatbelt Pretensioner Cross Link to Another Firing Loop Go To Pinpoint Test C . B1054 c - Driver Seatbelt Pretensioner Cross Link to Another Firing Loop Go To Pinpoint Test D . B1057 c - Driver Air Bag Cross Link to Another Firing Loop Go To Pinpoint Test E . B1231 13 RCM Crash Data Memory Full INSTALL a new RCM and CARRY OUT programmable module installation (PMI). REFER to Restraints Control Module (RCM) and Inspection and Repair After a Supplemental Restraint System (SRS) Deployment in this section. B1317 Continuous Lamp Battery Voltage High REFER to Section 414-00 . B1318 Continuous Lamp Battery Voltage Low REFER to Section 414-00 . B1342 24 RCM is Faulted INSTALL a new RCM and CARRY OUT programmable module installation (PMI). REFER to Restraints Control Module (RCM) in this section. B1871 25 Passenger Air Bag Deactivate Module Fault Go To Pinpoint Test F . B1884 27 Passenger Air Bag Deactivation (PAD) Warning Lamp Circuit Failure Go To Pinpoint Test G . B1890 27 Passenger Air Bag Deactivation (PAD) Warning Lamp Short to Battery Go To Pinpoint Test H . B2292 33 Restraint System - Seat Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test I . B2292 34 Restraint System - Seat Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test I . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test J . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault Go To Pinpoint Test K . B2434 53 Driver Seat Belt Buckle Switch Circuit Short to Ground Go To Pinpoint Test L . B2435 53 Driver Seat Belt Buckle Switch Resistance out of Range Go To Pinpoint Test M . B2477 54 Module Configuration Failure This DTC indicates programmable module installation (PMI) has not been done to a newly installed module. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. B2607 57 Harness/Configuration Mismatch This DTC indicates the RCM is configured incorrectly. CARRY OUT programmable module installation (PMI). REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. B2691 53 Seat Belt Buckle Switch Circuit Fault, Front Driver's Side Go To Pinpoint Test N . C1414 29 Incorrect Module Design Level VERIFY RCM part number is correct for vehicle.
CARRY OUT programmable module installation (PMI). REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. U0100 14 Lost Communication With ECM/PCM REFER to Section 418-00 to diagnose the communication concern. U2023 14 Fault Received From External Node REFER to Section 418-00 to diagnose the communication concern. U2050 14 No Application Present This DTC indicates programmable module installation (PMI) has failed. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. If DTC is retrieved a second time, INSTALL a new RCM and CARRY OUT PMI. REFER to Restraints Control Module (RCM) in this section. a DTC: Diagnostic trouble code, retrieved using scan tool.
c Cross-link DTCs will be retrieved in pairs to identify the cross-linked components.
b LFC: Lamp fault code, flashed on air bag warning indicator.

Apr 18, 2017 | Ford Cars & Trucks

1 Answer

2006 lincoln town car air bag light is on 5 beeps 5 times


The five beeps - five times would indicate a code 55 , but factory service info only goes to code 53 .

  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.

Did your air bag light flash at all ? Apparently this will do flash the air bag light codes as well .
Symptom Chart Condition Possible Sources Action
  • Air bag warning indicator is illuminated continuously
  • Fuse
  • Damaged wiring, terminals or connectors
  • A faulty diagnostic connector
  • A faulted RCM
  • A faulty instrument cluster
  • Go To Pinpoint Test A .
  • Air bag indicator flashing
  • Air bag/pretensioner supplemental restraint system (SRS) fault
  • REFER to DTC Priority Table.
  • Audible tone - DTCs retrieved
  • Air bag SRS system fault
  • REFER to DTC Priority Table.
  • No communication with the restraints control module (RCM)
  • Fuse
  • Diagnostic tool
  • Data link connector (DLC)
  • A faulted RCM
  • Circuitry
  • Go To Pinpoint Test V .
LFC - light flash codes .
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Table
DTC a LFC b Description Action To Take - Continuous The Air Bag Indicator is Illuminated Continuously, RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground Go To Pinpoint Test A . B1231 13 Crash Data Memory Full Install a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . B1317 Continuous Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to Section 414-01 . B1318 Continuous Battery Voltage Low CHECK battery voltage; to be above 9.0 volts. REFER to Section 414-01 . B1342 12 RCM Is Faulted Install a new RCM. B1869 NONE
Continuous lamp
Secondary air bag warning sounds if another fault is present Lamp Air Bag Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test B . B1870 NONE
Secondary air bag warning sounds if another fault is present Air Bag Warning Indicator Circuit Short to Battery Go To Pinpoint Test C . B1891 53 Air Bag Tone Warning Indicator Circuit Short to Battery Go To Pinpoint Test D . B1892 53 Air Bag Tone Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test E . B1921 14 Air Bag Diagnostic Monitor Ground Circuit Open Go To Pinpoint Test F . B2292 33 Restraint System - Safety Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test G . B2292 34 Restraint System - Safety Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test G . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2294 24 Restraint System - Curtain Fault (Driver Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2294 25 Restraint System - Curtain Fault (Passenger Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2295 22 Restraint System - Side Air Bag Fault (Driver Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2295 23 Restraint System - Side Air Bag Fault (Passenger Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault (Front Impact Severity Sensor Circuit Fault) Go To Pinpoint Test K . B2296 43 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 45 Restraint System - Impact Sensor Fault (Driver Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 44 Restraint System - Impact Sensor Fault (Passenger Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 46 Restraint System - Impact Sensor Fault (Passenger Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2434 51 Driver Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test L . B2435 51 Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test M . B2438 52 Passenger Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test N . B2439 52 Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test O . B2477 Continuous Module Configuration Error INSTALL a new RCM. B2691 51 Driver Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test P . B2692 52 Passenger Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test Q . C1414 15 Incorrect Module Design Level Go To Pinpoint Test R . C1947 49 Driver Seat Track Position Sensor Circuit Short to Ground Go To Pinpoint Test S . C1948 49 Driver Seat Track Position Sensor Circuit Resistance Out Of Range Go To Pinpoint Test T . C1981 49 Driver Seat Track Position Sensor Circuit Fault Go To Pinpoint Test U . - - No Communication with the Restraints Control Module Go To Pinpoint Test V . Your best bet have codes checked with a scan tool .

Jan 23, 2017 | Lincoln Cars & Trucks

1 Answer

Heated and cooled seat on 2004 expedition stopped working how to reset them


Heating and the cooling both don't work ? Just one seat or all seats ?
Your best bet have it checked for DTC'S - diagnostic trouble codes to start .
Climate Controlled Seat Module (CCSM) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 ECU Is Faulted CCSM INSTALL a new CCSM and CARRY OUT programmable module installation (PMI). REFER to Climate Controlled Seat Module . B1358 Ignition Switch or Blower Electronics Circuit Short to Ground CCSM Go To Pinpoint Test Q . B2477 Module Configuration Error CCSM This DTC indicates programmable module installation (PMI) has not been done to a newly installed module. CARRY OUT PMI. REFER to Section 418-01 . CLEAR the DTC. CARRY OUT the self-test. B2486 Climate Controlled Seat Module Voltage Out of Range CCSM DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 294 (WH/LB) for a fault. REPAIR as needed. If okay, REFER to Section 414-01 . Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . B2488 Thumbwheel Switch Voltage Out of Range High CCSM Go To Pinpoint Test R . B2521 Tach Circuit Failure CCSM Go To Pinpoint Test Q . B2729 Cushion Over-Temp Detected CCSM Go To Pinpoint Test S . B2730 Back Over-Temp Detected CCSM Go To Pinpoint Test S . B2731 Differential Temperature Fault CCSM Go To Pinpoint Test S . B2792 Heat Switch Short to Ground CCSM NOTE: If HEAT is pressed for greater than 20 seconds on the climate controlled seat switch, DTC B2792 will set in the CCSM.
CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 1551 (VT/WH) for a short to ground. REPAIR as needed. If okay, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . B2793 Cool Switch Short to Ground CCSM NOTE: If COOL is pressed for greater than 20 seconds on the climate controlled seat switch, DTC B2793 will set in the CCSM.
CLEAR the DTC. If the DTC does not clear, DEPOWER the supplemental restraint system (SRS). REFER to Section 501-20B . DISCONNECT driver safety belt buckle pretensioner electrical connector or passenger safety belt buckle pretensioner electrical connector of the affected seat and CONNECT restraint system diagnostic tool 418-F395 to the safety belt buckle pretensioner harness connector. CONNECT the battery ground cable. CHECK circuit 1550 (WH/OG) for a short to ground. REPAIR as needed. If okay, INSTALL a new climate controlled seat switch. Once the repair is complete, DISCONNECT the restraint system diagnostic tool from the safety belt buckle pretensioner harness connector and CONNECT the safety belt buckle pretensioner connector of the affected seat. REPOWER the SRS. REFER to Section 501-20B . U2362 UBP Invalid Data Node ID CCSM NOTE: DTC U2362 indicates a network concern, the CCSM is not the source of the fault.
CLEAR the DTC. If the DTC does not clear, REFER Section 418-01 .

Nov 26, 2016 | 2004 Ford Expedition

1 Answer

Service Air Bag light on


DTC B0058 Right Front/Passenger Pretensioner Deployment Loop Open.
The passenger seat belt pretensioner deployment loop consists of a seat belt pretensioner-RF and the seat belt pretensioner-RF high and low circuits. A shorting bar used within the seat belt pretensioner connector shorts together both the seat belt pretensioner high and low circuits when the connector is disconnected. This will help to prevent unwanted deployment of the pretensioner during servicing. During a frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the seat belt pretensioner. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a diagnostic trouble code (DTC) will be stored in memory.
DTC B0084 Left Front/Driver Seat Position Sensor Circuit
The inflatable restraint seat position sensor (SPS) is used to determine the proximity of a front driver or passenger seat position with respect to the frontal air bag. The SPS interfaces with the sensing and diagnostic module (SDM). The state of the SPS allows the SDM to disable stage 2 of the frontal air bag for a front seat that is forward of a forward/rearward point in seat track travel. The SPS is a hall effect sensor that is mounted on the inside seat track of both the driver and passenger seats. The seat track includes a metal bracket that shunts the SPS magnetic circuit creating 2 states of seat position. The shunted state represents a rearward seat position. The non-shunted state represents a forward position. The SPS provides 2 current ranges, one range for the shunted state and a second range for a non-shunted state. These 2 states are inputs to the SDM. State 1 (shunted) being the rearward threshold and state 2 (non-shunted) being the forward threshold. When the SDM receives input from a SPS that state 1 threshold is reached (seat is rearward) the SDM will not disable stage 2 deployment, if required by the deployment sensors. When state 2 threshold is reached (seat is forward) the SDM will disable stage 2 deployment on the side the seat is forward. The SDM monitors the SPS circuit and if a fault is detected the SDM will set codes B0083 or B0084 and defaults to disabling stage 2 frontal deployment. This will only default on the side of the vehicle the sensor has a fault. Its important to understand that the SPS is secondary to the passenger presence system (PPS) and the manual instrument panel (I/P) module disable switch. If either one of these devices are in the disable mode the passenger air bag will not deploy regardless of the SPS status.
You should take this to a qualified repair Shop ! Takes special tools to test .

Feb 26, 2016 | 2006 GMC Envoy

1 Answer

Hi i have just changed steering wheel on fiesta zetec 2003 for a ST150 2005 steering wheel will the air bags and connections be compatable with each other.


. Were did you check for codes ? an what are you checking with ? you need a factory scan tool to check for those type codes ? or the light flashes codes
Lamp Fault Code (LFC)
When the RCM detects a fault, it will cause the air bag indicator to flash a coded sequence called a LFC. The code is one digit. The digit is indicated by a number of flashes with a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indicator will remain lit as long as the key remains in the RUN position. If there are multiple LFCs, each LFC will flash in order of priority.
Each LFC has one or more associated DTC.
  1. Press TRIGGER. The RCM will run the On-Demand Self-Test and display On-Demand DTCs (reflecting hard system concerns) on the screen.


Restraints Control Module (RCM) DTC Index DTC LFC LFC Priority Description Action - Continuous 1 Air bag warning indicator is illuminated continuously Go To Pinpoint Test B . B1231 Continuous 3 Longitudinal acceleration threshold exceeded (Crash Occurred) Go To Pinpoint Test C . B1318 Continuous 4 Battery voltage low REFER to Section 414-00 . B1342 Continuous 2 RCM is defective DIAGNOSE and REPAIR other DTC(s) that are present. CLEAR the DTCs. REPEAT the self test. When or if DTC B1342 alone is present, INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this section. CLEAR the DTCs. REPEAT the self test. B1462 N/A N/A Safety belt switch circuit failure Go To Pinpoint Test AN . B1869 Continuous or Tone 39 Lamp air bag warning indicator circuit open Go To Pinpoint Test AJ . B1870 Tone 41 Lamp air bag warning indicator circuit short to battery Go To Pinpoint Test AK . B1876 4 24 Safety belt driver pretensioner circuit failure Go To Pinpoint Test T . B1877 4 23 Safety belt driver pretensioner circuit open Go To Pinpoint Test S . B1878 4 22 Safety belt driver pretensioner circuit short to battery Go To Pinpoint Test R . B1879 4 36 Safety belt driver pretensioner circuit short to ground Go To Pinpoint Test AF . B1880 4 27 Safety belt passenger pretensioner circuit failure Go To Pinpoint Test W . B1881 4 26 Safety belt passenger pretensioner circuit open Go To Pinpoint Test V . B1882 4 25 Safety belt passenger pretensioner circuit short to battery Go To Pinpoint Test U . B1883 4 38 Safety belt passenger pretensioner circuit short to ground Go To Pinpoint Test AH . B1885 4 37 Safety belt driver pretensioner circuit resistance low on squib Go To Pinpoint Test AG . B1886 4 39 Safety belt passenger pretensioner circuit resistance low on squib Go To Pinpoint Test AI . B1915 3 10 Air bag driver circuit failure Go To Pinpoint Test F . B1916 3 8 Air bag driver circuit short to battery Go To Pinpoint Test D . B1920 3 13 Air bag passenger circuit failure Go To Pinpoint Test I . B1925 3 11 Air bag passenger circuit short to battery Go To Pinpoint Test G . B1932 1 9 Air bag driver circuit open Go To Pinpoint Test E . B1933 2 12 Air bag passenger circuit open Go To Pinpoint Test H . B1934 1 29 Air bag driver inflator circuit resistance low on squib Go To Pinpoint Test Y . B1935 2 31 Air bag passenger inflator circuit resistance low on squib Go To Pinpoint Test AA . B1936 3 28 Air bag driver circuit short to ground Go To Pinpoint Test X . B1938 3 30 Air bag passenger circuit short to ground Go To Pinpoint Test Z . B1992 5 14 Driver side, side mount air bag circuit short to VBATT Go To Pinpoint Test J . B1993 5 32 Driver side, side mount air bag circuit short to ground Go To Pinpoint Test AB . B1994 5 15 Driver side, side mount air bag circuit open Go To Pinpoint Test K . B1995 5 33 Driver side, side mount air bag low resistance on squib Go To Pinpoint Test AC . B1996 6 17 Passenger side, side mount air bag circuit short to VBATT Go To Pinpoint Test M . B1997 6 34 Passenger side, side mount air bag circuit short to ground Go To Pinpoint Test AD . B1998 6 18 Passenger side, side mount air bag circuit open Go To Pinpoint Test N . B1999 6 35 Passenger side, side mount air bag low resistance on squib Go To Pinpoint Test AE . B2117 5 16 Driver side, side mount air bag low capacitance on squib Go To Pinpoint Test L . B2118 6 19 Passenger side, side mount air bag low capacitance on squib Go To Pinpoint Test O . B2141 5Hz 6 NVM configuration failure RECONFIGURE the RCM. REFER to Section 418-01 . B2226/ B2227/ B2855/ B2856 N/A N/A Front crash sensor failure Go To Pinpoint Test AR . B2228/ B2230/ B2232/ B2234 N/A N/A Air bag driver, 2nd stage fault Go To Pinpoint Test AL . B2229/ B2231/ B2233/ B2235 N/A N/A Air bag passenger, 2nd stage fault Go To Pinpoint Test AM . B2433/ B2434/ B2435 N/A N/A Buckle switch, driver failure Go To Pinpoint Test AO . B2437/ B2438/ B2439 N/A N/A Buckle switch, passenger failure Go To Pinpoint Test AP . B2477 Continuous 7 Module configuration failure Check for correct RCM for this vehicle. RECONFIGURE the RCM. REFER to Section 418-01 . B2853/ B2854/ B2873/ B2873/ U2027 5 20 Left side crash sensor internal fault/short to ground/VBATT/ID fault Go To Pinpoint Test P . B2852/ B2874/ B2875/ U2028 6 21 Right side crash sensor internal fault/short to ground/VBATT/ID fault Go To Pinpoint Test Q . C1947/ C1948/ C1982 N/A N/A Seat track position sensor, driver failure Go To Pinpoint Test AQ .

Oct 14, 2015 | Cars & Trucks

1 Answer

Hi there exactly what parts will need to be replace on my 2009 chevy impala with srs light on.Four codes are b001a and b001b each code is listed twice. thanks for the help


Both seat belts in front. The entire mechanism. And you can't get one from a wrecked car. You might want to check for recalls on these. Unless you've been in an accident.

Sep 06, 2015 | 2009 Chevrolet Impala

1 Answer

2009 Chevy Impala LT code b001b What to do with this?


Code B001b is for Sensing Diagnostic Module (SDM) for Air bag.

Potential Causes:-
  • Drivers Seat Belt Anchor Pretensioner
  • Passengers Seat Belt Anchor Pretensioner
  • Sensing Diagnostic Module (SDM)
  • Sensing Diagnostic Module (SDM) Wiring
1. Confirm the passenger seat belt anchor pre tensioner connector position assurance is clicked into place.

2. If not, click it in and retest.

3. If the codes reset, disable the Supplemental Inflatable Restraint (SIR) system.

4. Substitute a 2.0 to 2.2 ohm resistor for the passenger seat belt anchor pretensioner. Refer to Tech Tips for a load tool.

5. Retest for the code to reset.

6. If the code resets, check for harness problems between the seat belt anchor pretensioner and the Sensing Diagnostic Module (SDM).
Tech Tips: At the beginning of the 2009 model year, the Impala began being equipped with two pre tensioners for the driver and two pre tensioners for the front passenger. The first pretensioner is still attached to the seatbelt retractor. The second pretensioner is attached to the anchor point for the seat belt.
A load tool can be fashioned from an 1157 light bulb and socket. Turn the bulb into the socket. Using an ohmmeter, determine which 2 wires have 2 - 3 ohms of resistance. Use those 2 wires as the load tool.

Mar 30, 2015 | 2009 Chevrolet Chevrolet Impala LT

1 Answer

Code b001b b001a sub 04 2013 impala


Was this car in and accident . If so both codes refer to front pretensioner Assemblys at the seat belts

Nov 30, 2013 | 2010 Chevrolet Impala

4 Answers

Airbag light has started flashing then came on this is the first time we have had an issue with this. after flashing the light stays on.


get the code, but my guess is it\'s the seat belt pre-tensioner connectors. There is a TSB to replace them on both seats at the same time. Not a recall so not covered under warranty. Please rate highly if this helps.
TSB 05-17-11
RESTRAINT SYSTEM - SAFETY BELT BUCKLE AND PRETENSIONER DIAGNOSTIC TROUBLE CODE (DTC) B1877 AND/OR B1881
FORD:
2001-2004 Escape

This article supersedes TSB 04-24-4 to update the service procedure.
ISSUE:
Some 2001-2004 Escape vehicles may exhibit an intermittent air bag lamp on and diagnostic trouble code (DTC) B1877 and/or B1881. This may be caused by a variation in the electrical continuity between the pins of the driver and/or passenger side wiring harness and the buckle pretensioner connector. If this condition were to occur, the air bag system remains fully functional.

ACTION:
Install a replacement harness connector kit ON BOTH the driver and passenger safety belt buckle pretensioners, even if the DTC is present for only one side. The kit includes improved connector halves to replace the existing connectors on both the body harness and the safety belt buckle pretensioner.
One kit is required per side (2 kits per vehicle). Refer to the instruction sheet included in the kit for complete repair procedure.


OPERATION

DESCRIPTION

TIME


051711A
2001-2004 Escape Install A Replacement Harness Connector On Both The Body Side And Safety Belt Buckle Pretensioner Harness For Both Driver And Passenger Safety Belt Buckle Pretensioners (Do Not Use With 14056D)
2.0 Hrs.

Sep 09, 2010 | 2004 Ford Escape

1 Answer

Air bag sensor keeps flashing


If a concern is detected, the air bag control module will communicate by flashing the warning indicator. A diagnostic trouble code (DTC) is logged by the air bag control module in a nonvolatile memory. For additional information, refer to Diagnosis and Testing in this section.
Lamp Fault Codes (LFC)
Item Part Number Description 1 One flash cycle: Driver air bag trouble code 2 Two flash cycle: Passenger air bag trouble code 3 Three flash cycle: Trouble code common to both driver and passenger air bag circuit 4 Four flash cycle: Safety belt pretensioner trouble code common to both driver and passenger pretensioner circuits 5 Five flash cycle: Driver side air bag trouble code 6 Six flash cycle: Passenger side air bag trouble code 7 Not used 8 Not used

Apr 10, 2009 | 2001 Ford Focus

Not finding what you are looking for?
2009 Chevrolet Impala Logo

994 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...