Question about 1996 Nissan 200SX

Open Question

If the tcc solenoid in 98 nissan altima is bad, will it have problems accelerating in fourth and fifth gears?

If tcc solenoid in 98 nissan altima is bad, would the check engine light come on? could this issue have anything to do with the clutch system, or flywheel?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ginko
  • 19396 Answers

SOURCE: torque converter clutch

It should be attached to transmission block, I will see if I find a diagram.

Posted on May 29, 2008

Ad
  • 1 Answer

SOURCE: 94 Nissan Altima accelerator problems

check your throttle position sensor

Posted on Aug 13, 2008

  • 2 Answers

SOURCE: 2003 nissan altima 2.5s transmission rough shift

Probably sensors! I have already replaced the crankshaft positioning sensor once, nissan replaced it once under recall and now it is bad again! Plus my speed sensor is bad too! Go to any part store and get diagnostic test ran, it will tell what sensors are bad.

Posted on Oct 02, 2008

  • 3 Answers

SOURCE: 2003 Nissan Altima 2.5S, Check Engine Light Problem.

this problem could be caused by the mass air flow censor, i had the same problem with my car. it is really pricey at the dealer so you might want to check elsewhere for this part. I found one at a scrap yard for 85% less that the dealer and i also got life time warranty, the dealer does not offer any warranty on this part.

Posted on Oct 22, 2008

tommyboinow
  • 324 Answers

SOURCE: 1994 nissan altima gear shift lockout problem

replace the brake pedal switch, it is mounted in front of the brke pedal, this is what makes the silanoid work, if it is not working the silanoid will not.

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Two codes coming up on car even after fixing alot on car now need to figure out low cost ways to fix P0744 & P0722 code issues spent 1,800 on car & have spent 1,400 already in parts & labor.


you need a better mechanic that traces ALL of the possibilities of each code, not just read the code and trow in a part hoping that it's fixed ~ it can be wiring as well, not just plug in a new part as mentioned on the 2nd trouble code to the vehicle speed sensor

P0744 Torque Converter Clutch Circuit Intermittent


P0722 Output Speed Sensor No Signal

the first of the 2 looks to be more intensive to trace and find out the problem & the 0722 is the easier job for an intermediate mechanic to trace the wiring for continuity

Apr 20, 2015 | Cars & Trucks

2 Answers

Torque converter clutch


It should be attached to transmission block, I will see if I find a diagram.

May 29, 2008 | 2001 Nissan Altima

1 Answer

Ssanyong Kryon auto, the gears jump to neutral between fourth and fifth then engage with a bump?


Not sure, but 5th may be a lock up torque converter rather than another "real" gear. If so, solenoid for this may be bad, or torque converter may be bad. Have you changed the trans fluid and filter?

Jan 13, 2015 | SsangYong Kyron Cars & Trucks

3 Answers

Ihave code p0731 stuck in 1st ratio .. what mean that code?


obviously refers to auto trans , could just need the trans fluid level topping up or even changing , if this does'nt resolve the problem then a more in depth diagnosis would be required at a repair shop as could be the ECU for example but do the fluid checks and go from ther ,keep me posted

May 09, 2014 | 2009 Hyundai Azera

1 Answer

Change shift linkage on 93 sentra


More than likely it's not the linkage. Sounds like the fourth to fifth synchronizer is very badly worn, which will cause the shifter to "pop out" of fifth gear.

Mar 05, 2012 | Nissan Sentra Cars & Trucks

2 Answers

1993 Chavrolet Cavalier it shakes badly in parking mode


Yes I have repaired both of these concerns on hundreds on 4 cyl. GM models most of the time the bad engine mount is the one on the passenger side of the car.And it is the TCC solenoid that gets stuck on.

Dec 25, 2009 | 1993 Chevrolet Cavalier

1 Answer

97 5 speed. Almost frozen gears


sounds like the clutch pressure plate is worn out or the clutch disc is

Apr 19, 2009 | 1997 Nissan.5 Altima

1 Answer

1995 Nissan Altima will not stay on


Change the cranksahft sensor, it hapend to my car and I solve this problem with it.

Jan 20, 2009 | 1995 Nissan Altima

1 Answer

94 Nissan Altima accelerator problems


check your throttle position sensor

Aug 06, 2008 | 1994 Nissan Altima

Not finding what you are looking for?
1996 Nissan 200SX Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...