Question about Cars & Trucks

Open Question

Timing belt marks on a Chana JL4740 engine - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 2920 Answers

SOURCE: timing on 1999 toyota camry 2.2

there are 2 points on the crank and on the drive shaft that have to be lined up and then you put the belt on with the lined up point to point.the belt does not have to be marked

Posted on Aug 09, 2008

Ad
  • 740 Answers

SOURCE: timing marks needed for '91 1.6L SOHC

Here is your diagram, Please leave me a FI YA comment if I fixed ya thanks http://www.2carpros.com/car_repair_information/tec_info/1998/eagle/talon/1998_eagle_talon_timing_belt_diagram_marks.htm

Posted on Dec 20, 2008

daves944
  • 1050 Answers

SOURCE: I need timing marks i am replacing a timing belt.

This link explains it very well:

http://www.aa1car.com/library/timing_belt_aveo.htm

Posted on Apr 17, 2009

yotaguy
  • 232 Answers

SOURCE: need to find the marks for replacing the timing belt.

I hope these are the right ones for your motor,note on the cam pulleys the pointers at the top line up with the marks on the pulleyscd75b48.jpg005d7b7.jpg

Posted on Apr 21, 2009

  • 5 Answers

SOURCE: engine timing

put car at top dead center then put the rotor on distributor to the first piston firing

Posted on Nov 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi ! I replaced the engine of my Chana star 13000 but it do not want to start? I changed all the electronic parts of the old engine who was running but overheated.


Check fuel supply first. Remove the pipe feeding the injectors and turn the ignition on. One line feeds, one returns to the tank. Sometimes they get swopped. If you have fuel pressure, then check for spark. If you have fuel supply and sark, then you could have a valve timing or ignition timing problem. Also check timing belt. A broken belt or chain will do the same ...

Jul 02, 2016 | Cars & Trucks

1 Answer

Looking for timing marks on chana star engine


should be on block and cam gear where the belt or chain is .

Jan 16, 2016 | Cars & Trucks

1 Answer

Loking for illustration off chana star valve timing marks urgent and does if bent valves if putted valve timing incorrectly


Hi there
Well if you done the motor and you havent timed it correctly then you will get a knocking noise and dependens on the motor then yes it could bend the push rods or tight tappets or out of timing the valves can bend,hole in pistons bent rockergear etc.
But depends on the motor if you time it with number 1 piston is TDC number 1 and last valves rocking [depending on how many cylinders you have 4 /6/ etc and set distributor firing No 1

Nov 16, 2014 | Cars & Trucks

1 Answer

Chana bakkie hard to start


ck compression and timing belt

Sep 02, 2014 | Cars & Trucks

1 Answer

Hi i am looking for a diagram that can help me set the timing belt timing on a chana 1000 star


I'm sure if you are replacing the timing belt then you know what you are doing, but I don't know how to describe how to do it without knowing the year, make, model and engine size. I am sure there is not a diagram to go by, but it is a precise order of taking the assembly out and replacing it so , if you need that information I will need your information Please. Hope to Help.

Feb 02, 2014 | Cars & Trucks

1 Answer

Timing belt timing marks


Instructions
  1. Remove the Timing Belt 3.0 V6
    • Place the Voyager's engine in the TDC no. 1 position for cylinder firing in order to get proper alignment. Disconnect the negative cable on the battery.
    • 2Take off the accessory drive belts, and take out engine mount insulator, located in the engine support bracket. Detach the engine support bracket and take off the torsional damper and crankshaft pulleys. This ensures easier access to the timing belt.

    • 3. Locate the 2- to 3-inch wide timing belt in the front of the engine. Remove the cover of the timing belt.
    • 4Mark the course of rotation on the belt as a reference if you plan to reinstall it. Slacken the timing belt torsioner bolt and take off the timing belt. Detach the timing belt torsioner if needed.
    • 5Remove the crankshaft sprocket and the flange shield of the crankshaft sprocket. Secure the camshaft sprocket using a spanner tool MB990775, or something similar, and take off the bolt and washer to the camshaft sprocket.
    Install the Timing Belt
    • 6Use the retaining washer and bolt to fit the camshaft sprocket onto the camshaft. Utilize the spanner tool MB990775 and tighten the bolt. Mount the crankshaft sprocket and put on the timing belt torsioner and tensioner spring if it was removed. Hook the higher end of the spring to the water pump pin and bottom end to the tensioner bracket with the hook facing out.
    • 7Rotate the timing belt tensioner in a counterclockwise turn and tighten the bolt to momentarily hold it in place. Turn the crankshaft sprocket until the timing mark lines up with the timing mark on the oil pump timing mark. Revolve the back camshaft sprocket so that its timing mark lines up with the generator bracket timing mark. Turn the radiator side camshaft sprocket so that the mark aligns with the inner timing belt cover mark.
    • 8Connect the timing belt onto the Voyager's crankshaft sprocket, keeping the belt tight on the side of tension. Install the belt in the same rotational direction if using the original timing belt. Put the timing belt on the radiator side of the camshaft sprocket, and place the belt underneath the water pump pulley first, and follow that by putting it over the back camshaft sprocket and the tensioner.
    • 9Create tension on the side of the timing belt and correctly line up all timing marks. Put the crankshaft sprocket flange into place and loosen the tensioner bolt to allow the tensioner spring to put tension on the belt. Turn the crankshaft two clockwise turns. Line up the timing marks and tighten the tensioner bolt. Put on the timing belt cover and engine support bracket.
    • 10Put the engine mount insulator, crankshaft pulleys and torsional damper into place. Mount the accessory drive belts, connect the negative battery cable and check that the engine runs properly.

Sep 12, 2012 | 1988 Plymouth Voyager

1 Answer

Need to know what the timing marks and locations for replacing the timing belt


Timing Belt Removal & Installation 3.0L Engine To Remove:
Exploded view of the timing belt and sprocket assembly (3.0L engine) 86723255.gif

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts. Remove the engine mount insulator from the engine support bracket.
  3. Remove the engine support bracket. Remove the crankshaft pulleys and torsional damper. Remove the timing belt covers.
  4. Rotate the crankshaft until the sprocket timing marks are aligned. The crankshaft sprocket timing mark should align with the oil pump timing mark. The rear camshaft sprocket timing mark should align with the generator bracket timing mark and the front camshaft sprocket timing mark should align with the inner timing belt cover timing mark.
  5. If the belt is to be reused, mark the direction of rotation on the belt for installation reference. Mark the direction of travel for the timing belt for correct installation 86723p72.jpg
  6. Loosen the timing belt tensioner bolt and remove the timing belt.
  7. If necessary, remove the timing belt tensioner. Turn the center tensioner pulley bolt until the timing belt has enough slack . . . 86723p73.jpg
    . . . then slide the timing belt off of the camshaft sprockets 86723p74.jpg
  8. Remove the crankshaft sprocket flange shield and crankshaft sprocket.
  9. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and remove the camshaft sprocket bolt and washer. Remove the camshaft sprocket.
To Install:
  1. Install the camshaft sprocket on the camshaft with the retaining bolt and washer. Hold the camshaft sprocket using spanner tool MB990775 or equivalent, and tighten the bolt to 70 ft. lbs. (95 Nm).
  2. Install the crankshaft sprocket.
  3. If removed, install the timing belt tensioner and tensioner spring. Hook the spring upper end to the water pump pin and the lower end to the tensioner bracket with the hook out.
  4. Turn the timing belt tensioner counterclockwise full travel in the adjustment slot and tighten the bolt to temporarily hold it in this position.
  5. Rotate the crankshaft sprocket until its timing mark is aligned with the oil pump timing mark.
  6. Rotate the rear camshaft sprocket until its timing mark is aligned with the timing mark on the generator bracket.
  7. Rotate the front (radiator side) camshaft sprocket until its mark is aligned with the timing mark on the inner timing belt cover.
  8. Install the timing belt on the crankshaft sprocket while keeping the belt tight on the tension side. NOTE: If the original belt is being reused, be sure to install it in the same rotational direction.
  9. Position the timing belt over the front camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the rear camshaft sprocket and finally over the tensioner. CAUTION
    If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.
    Rent or borrow the special tool to hold the camshaft sprockets steady . . . 86723p75.jpg
    . . . while loosening the center retaining bolt on the camshaft pulley, then . . . 86723p76.jpg
    . . . remove the camshaft sprocket from the end of the camshaft 86723p77.jpg
    Timing belt tensioner and spring positions 86723254.gif
    Timing belt routing and timing mark locations 86723256.gif

  10. Apply rotating force in the opposite direction to the front camshaft sprocket (radiator side) to create tension on the timing belt tension side. Check that all timing marks are aligned.
  11. Install the crankshaft sprocket flange.
  12. Loosen the tensioner bolt and allow the tensioner spring to tension the belt.
  13. Rotate the crankshaft two full turns in a clockwise direction. Turn the crankshaft smoothly and in a clockwise direction only.
  14. Again line up the timing marks. If all marks are aligned, tighten the tensioner bolt to 250 in. lbs. (28 Nm). Otherwise repeat the installation procedure.
  15. Install the timing belt covers. Install the engine support bracket. Tighten the support bracket mounting bolts to 35 ft. lbs. (47 Nm).
  16. Install the engine mount insulator, torsional damper and crankshaft pulleys. Tighten the crankshaft pulley bolt to 112 ft. lbs. (151 Nm).
  17. Install the accessory drive belts.
  18. Reconnect the negative battery cable.
  19. Run the engine and check for proper operation.
prev.gif next.gif

Aug 17, 2010 | 1997 Dodge Caravan

2 Answers

Need the timing marks for 2001 hyundai tiburon


1.5L And 1.6L Engines

a826891.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


4e7384e.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines

238c1f1.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


b1c71ee.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines


c200f83.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines

656db91.jpg

Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines

7208166.jpg

Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines


7080ea8.jpg

Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)

3b377fb.jpg

Fig. Installation of the timing belt-3.0L (VIN G) engine




7b32092.jpg


Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

Apr 13, 2010 | 2001 Hyundai Tiburon

1 Answer

Timing belt timing marks, 1997 ford escort where are they?


Ford Escort/Tracer 1991-1999 Repair Guide

REMOVAL & INSTALLATION 1.8L Engine

(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable.
  2. Remove the timing belt covers.
  3. Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
  4. Remove the crankshaft pulley and hub.
  5. If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
  6. Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
  1. Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
  2. Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
  3. Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
  4. Install the timing belt.
  5. Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
  6. Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.

fbe49f2.jpg
Fig. 1: Timing marks are located on the camshaft pulleys as shown-1.8L engines

5bb74d0.jpg

Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned-1.8L engines

9cafc26.jpg

Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position-1.8L engines

72dc9cd.jpg
Fig. 4: Check the timing belt deflection at the location shown-1.8L engines

  1. Make sure the camshaft pulley marks are aligned with the seal plate marks.
If the timing marks are not aligned, remove the belt and repeat the procedure.


I hope help you with this; remember rated this help. Good luck.

Sep 11, 2009 | 1997 Ford Escort

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...