Question about Cars & Trucks

Open Question

Looking for specification on dunham bush mid wall splits

Looking for specs.and models of dunham bush mid wall splits

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the specifications for all the sensors


lt's based on the engine and manufacturer, and year model. Like if you wanted to know specs for GM model cars or trucks, you would look at year and engine specs for sensors for that engine. They build the engines and models , then design the
sensors around the computer controls for that application. you have to get specific.

May 14, 2016 | Cars & Trucks

1 Answer

? looking the bolt tension specs for flywheel and clutch pressure plate for 4hf1 thank you


Torque Specification - National Truck Spares ' Parts

www.nationaltruckspares.com.au/Parts.aspx?ProductTypeID=8...
1073, 4BC2 tq, Isuzu, Torque Specification, KT26 TLD57 NKR57 NPR57 ... 1075, 4HF1Tq, Isuzu, Torque Specification, NKR66 NPR66, 92 - 03, 4HF1, 4334

Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

boxwrench.net/specs/chevy_sb.htm
Flywheel (Clutch). Thread Locker, 60 ft-lbs. Clutch Pressure Plate, Thread Locker, 35 ft-lbs. Centerbolt. (Harmonic Damper). Engine Oil, 60 ft-lbs. Bellhousin

Nov 07, 2015 | Cars & Trucks

1 Answer

What are the torque specs for the body bushings


your going to need a service manual or installation body parts torque specs.
www.ask.com/mfg.name/make/model/body_bushing/torque_limits/
/torque_instruction/
/torque_requirement/
www.manualsonline.com/mfg.name/make/model/torque_instruction

Apr 21, 2015 | Cars & Trucks

1 Answer

Lower my car 1.5 inch(H&R lowering spring)...put new control arms w/bushings,ball joints, bilstein struts, and axles. now driver side axle looks short in length. can see cv boot streching to much.match...


Without a good look i couldnt advise ,only to return to factory spec as this lowering will affect the vehicle in as much as it will not pass its anual vehicle inspection as this modification will deviate from the original certificate of homoglonation specifications which cover the design height of the vehicle and any variation of these specs are classed as illegal and as such will incur a fine from the traffic police and also will render the insurance invalid as the vehicle is not to its design specs .

Oct 16, 2013 | Volkswagen Jetta Cars & Trucks

1 Answer

I was looking for valve adjustment specs on my 1993 Toyota tercel 1.5L how to procedure


There are no valve adjustment specs as the valves are hydraulic controlled . If you have a noise it will be from faulty/worn followers .Or from worn rocker bushes and shafts

Sep 28, 2013 | 1993 Toyota Tercel

1 Answer

Need to find repair manual for a dunham model 3000


hi mate visit www.manualsonline.com

Sep 05, 2012 | Cars & Trucks

1 Answer

What is the toe adjustment for a 1998 ford windstar 3.8L


Hello Snsimpson



Here are all the specs for the Windstar.


FRONT ALIGNMENT (CURB HEIGHT WITH 1/2 TANK OF FUEL)
Camber

Nominal -0.25°
Minimum -0.75°
Maximum +0.25°
Split 0.0°±0.5° Caster
Right

Nominal +3.80°
Minimum +3.05°
Maximum +4.55°
Split -0.5°±0.5° Left

Nominal +3.30°
Minimum +2.55°
Maximum +4.05°
Split -0.5°±0.5° Total Toe [1]

Nominal -0.10°
Minimum -0.40°
Maximum +0.20° Clear Vision [2]

Nominal -0.2°
Minimum -2.8°
Maximum 3.2° REAR ALIGNMENT (CURB HEIGHT WITH 1/2 TANK OF FUEL)
Camber

Nominal 0.0°
Minimum -0.3°
Maximum +0.3° Total Toe [1]

Nominal -0.06°
Minimum -0.40°
Maximum +0.28° [1] Positive value specifications for toe-in, negative value specification for toe is toe-out. [2] Negative value specification for clear vision is counterclockwise.

Nov 16, 2010 | 1998 Ford Windstar

1 Answer

Torque specs for 2000 chevy silverado truck 4.3 v-6 engine


Not sure what torque spec's your looking for.
Go to www.AutoZone.com, enter your vehicle information and check specifications. You should be able to look up the torque spec's your looking for.
Good luck.
Regards,

May 02, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Jerking motion in front end when applying brakes etc


Hi

I take it you mean the 2 large round bush rubbers, at front of the sub-frame with the large bolt through the center ?

Usually if they are shot, you can see the splitting in them, if they look OK, I do not think this is your problem

What about the 2 Top front cross member mountings, they have a habit of splitting away from the bonding, and this can give strange jerking problems.

Jack up the car on the cross member, and support the body on the 2 front jacking points, better to remove the wheels, and lower the jack a little, and you should be able to see any problem with them straight away, and see even better if you lever with a large screwdriver.

I hope this is of help.

Good Luck

John.

Jan 18, 2009 | 1989 Jaguar XJ6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...