Question about 1998 Toyota Tacoma

Open Question

Reprogram throttle position sensor 05 tacoma - 1998 Toyota Tacoma

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor on a 1996 toyota tacoma 2.7 located.


Camshaft Position Sensor

1996 Toyota Truck Tacoma 2WD 2.4L EFI DOHC 4cyl

The Camshaft Position Sensor is located: Under hood, passenger side, front engine area, below valve cover, mounted in distributor

Oct 14, 2014 | 1996 Toyota Tacoma

2 Answers

How do I replace a TPS(throttle position sensor) on a 1996 Toyota Tacoma? I need step by step instructions.


the short reply is you cant,you must replace the throttle body try a breakers yard .

May 08, 2014 | Cars & Trucks

1 Answer

What does a throttle positioning censor for an 05 ford focus look like


I suggest you google 05 ford focus throttle positioning sensor. This sensor keeps you air intake throttle at the proper position when the engine is cold and changes position when the engine has warmed up. to locate the sensor, remove the hose that comes from the air filter housing to the engine. the hose you removed was connected to the air throttle. you can manipulate the position of this throttle by having someone push the gas pedal down slowly while you watch the throttle move. notice that the gas pedal cable is connected to the mechanism that opens and closes the air throttloe. also notice that beside this mechanism, you have an electric throttle positioning sensor. Pay close attention to the existing throttle positioning sensor before you remove it if you are planning on replacing this sensor. because if you do not install the new sensor in the same degree that the old one was in, you will throw the calibration off. word of advice. buy some throttle cleaner from your local auto parts. turn the car on with the air filter to throttle body hose off and have someone push the gas pedal down slightly to keep the engine from turning off. spray the throttle body cleaner til all the black crud comes off the inside of the throttle body. this dirty crud is what was making your throttle stick and not working properly.

May 01, 2014 | 2005 Ford Focus

2 Answers

Engine power reduced


The Catalytic Converter maybe clogged, I have a 2001 3800 Engine that just had the intake Manifold gasket changed 80,000 miles and three days later the car has issue with power due to antifreeze clogging the converter. Changing converter now, Dealer checked it and found the converter after I looked at it for three days to find nothing with the engine.

Feb 24, 2014 | Cars & Trucks

1 Answer

05 c5500 gmc duramax


run fault codes and check for throttle position sensor.

Jan 06, 2014 | Cars & Trucks

1 Answer

My Toyota Tacoma idles to high . How do u adjust throttle


sounds like 0 2 sensor is not sending signal to throttle thus keeping it in cold start position

Mar 26, 2013 | Cars & Trucks

1 Answer

05 sharan 1.8 t manual revs high when changing from 1st to 2nd gear


you'll need to take it to your local shop or dealer and have the throttle body module looked at. There are sensors in there and it may to be either replaced or reprogrammed

Dec 04, 2012 | Volkswagen Passat Cars & Trucks

1 Answer

My '05 Tacoma 3.5L has developed a quick skip or hesitation when I excelorate. I had the spark plugs replaced but the problem continues.


Could be a problem with the throttle position sensor. If the carbon track on which the throttle plate slider contact runs has dirt on it or is worn then this would interrupt signal to the ECU. The TPS has three pins in the socket. Two (usually the outer two) supply the 5 volts reference and 0 volts ground to the carbon strip. the middle pin measures the voltage 'tapped' by the throttle position sliding contact. Disconnect the TPS lead and with a voltmeter simply measure the resistance between one of the outer pins and the middle pin as the throttle plate is opened and closed. The response should be smooth chnage in resistance with no 'drop-outs'. If a drop is consistently detected at a particular throttle plate position then the TPS needs to opened and cleaned if dirty or replaced if faulty.

May 12, 2011 | 2005 Toyota Tacoma

1 Answer

I have a 1996 tacoma, have had a problem with a


Tap on the mass air flow,and see if it changes idle,if it does,it is the problem,If the throttle position has to be tapped on,then it could be defective,change it out for a new one.

Apr 28, 2010 | 1997 Toyota Tacoma

Not finding what you are looking for?
1998 Toyota Tacoma Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...