Question about 2007 Buick LaCrosse CXL Sedan
Rf turn signal bulb
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: signal bulb on 2003 buick regal
To change front turn signal –
open the hood; look in back of headlight; two white clips; pull straight up, and then whole headlight comes out including turn signal; it is all one unit; remove rubber cover, then you take bulb out of unit. Mechanism that bulb fits in will need to be turned clockwise (looking from the front) and pulled to get it out of the larger unit holding all lights. Be sure and put rubber cover back on before re-inserting the two white clips.
Posted on May 07, 2009
The bright light fitting is the same as the dim so take it apart fist to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you a little more space.
Posted on Apr 03, 2010
The relay under the hood may have gone out. We had the same problem on our 2007 Buick LaCrosse CX. The bulbs were fine, high beams worked, all turn signals and everything except the low beams turned on. Turns out the relay had gone bad.
Posted on Sep 07, 2010
SOURCE: HOW DO I CHANGE THE
Asuming you mean taillight/turnsignal, and not highmounted brake light:
1.open the trunk
2.Remove 4 wingnuts on trunk trim (there are two on each side)
You can do it by only removing 2 on one side, but it makes a nicer job,
3.Pull back the trunk "trim" the carpeted cardboard
4.Remove 2 wingnuts which hold the taillight assembly in place
Pull out the taillight assembly; you might want to remove (i.e. unattach or unplug) the wiring harness
5.Turn the particular bulb's socket (there's 5 back there: 2 tail, 1 back up, 1 side marker, 1 brake/turn) counterclockwise, and it removes from the assembly, holding the bulb.
6. Pull out bulb and replace.
6. Reverse steps to reassemble.
Posted on Jan 25, 2011
Tips for a great answer:
May 23, 2016 | Buick Cars & Trucks
Mar 20, 2016 | Buick Cars & Trucks
Feb 13, 2016 | Buick Cars & Trucks
Jan 17, 2013 | 2007 Buick LaCrosse CX
Jul 29, 2011 | Buick LaCrosse Cars & Trucks
Jul 14, 2011 | 2006 Buick LaCrosse
Sep 07, 2010 | 2007 Buick LaCrosse CXL Sedan
128 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: