Question about Cars & Trucks

Open Question

Workshop manual tongda cb 580 balancer - Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do change crankshaft seal on toyto 4runner sr5 97


front seal --remove harmonic balancer/ front pulley
if it is a belt for the cam shafts set it on tdc no1 piston so that all the marks line up then remove the belt and the bottom pulley to get to the seal
if it is a chain the seal will be after the balancer
if it is a rear main seal, remove the transmission and flywheel
best advice is to get a workshop manual for the vehicle and follow the directions and photos closely

Sep 10, 2016 | 1997 Toyota 4Runner

1 Answer

I have a oldsmobile intrigue 2001 3.5 engine how do you remove the harmonic balancer pulley


remove drive belts
undo crank nut if there is one
fit a harmonic balancer remover puller
pull the balancer of
Note take care in the removal as there may be a crank sensor at the balancer
best get a workshop manual for photos on the job

Jul 02, 2015 | Oldsmobile Cars & Trucks

1 Answer

1999 Sirion. How do I remove the harmonic balancer?


You're best bet to get a full shop manual for this car is going to be on eBay Daihatsu Workshop Manual eBay


To get just the harmonic balancer off you will need a heavy duty gear puller; they do make harmonic balancer pullers but a really good gear puller will work just as well. Whatever you do, don't try prying it off with a bar, or hitting it with a hammer; you'll either damage the crankshaft or the balancer or possibly both.
It's also a lot easier to do when the motor is out of the car; you'll need a lot of room to work getting it off.
Back to the balancer; take all of the belts off, loosen the bolt in the center of the balancer (you will need to lock the flywheel so the crank doesn't turn when you try to loosen the bolt). Once it's loosened, take it out a couple of turns, but no more than that, attach the puller and start pulling it off, once you see it move, you can take the puller off, remove the bolt, you should be able to pull it off by hand now; if not, reattach the puller, and finish pulling it off. There is a little "guide pin" in the crankshaft called the Woodruff Key, you'll want to take it out and inspect to see if it shows any wear, or distortions, if so, replace it. Leave it out until you're ready to reinstall the balancer; it's how the balancer lines up with (and holds it in place) crankshaft. This is not a job for a beginner.

Jun 22, 2015 | Daihatsu Cars & Trucks

1 Answer

Where can I find the full service manual for Bmw x1 2011? Brake pad, disc replacement, suspension, steering system alignment and balancing etc... Also how to repair the punctured run flat tyre on Bmw x1???


Take the flat tyre to a tyre shop and have it repaired there as believe or not , puncture repair requires the correct tools and procedure for safety. As for the rest a good workshop manual should have that information or get a service hand book from the dealer service centre.

May 23, 2014 | Cars & Trucks

1 Answer

Is there any marks that I should align the counter balance shaft to on a zzr 1100 c kawazaki


There are bound to be marks for a key item like this. Go online to a Kawa forum or manual. Failing that look up a workshop manual which you should really have given you have the engine in bits.

May 20, 2014 | Cars & Trucks

1 Answer

I need a fuse box diagram for a 1992 Ford Ranger. Any idea where I could find one?


owner manual.

here's the big ones for 1994 ranger. all i have
Section 18-01: Wiring and Circuit Protection 1994 All Ranger, Explorer and Aerostar Vehicles Workshop Manual
SPECIFICATIONS Specifications

High Current Fuses And Circuit Breaker — Ranger 2.3L, 3.0L And 4.0L
Circuit Size Location Electric Fuel Pump 20 Amp Fuse Power Distribution Box Headlamp Switch Feed 40 Amp High
Current Fuse Power Distribution Box #36 Circuit Alternator Output #2 15 Amp Fuse Power Distribution Box Fuse Panel 60 Amp High
Current Fuse Power Distribution Box Power Locks 20 Amp High
Current Fuse Power Distribution Box #38 Circuit Alternator Output #1 12 Ga Fusible
Link Integral with 14305 W/A Powertrain Control Module and Power Relay 30 Amp High
Current Fuse Power Distribution Box 4x4 Electric Shift 20 Amp High
Current Fuse Power Distribution Box Ignition Switch Feed 60 Amp High
Current Fuse Power Distribution Box High Beams and High Beam Indicator 22 Amp C.B. Integral with Headlamp Switch Front Wiper and Washer 6 Amp C.B. In Fuse Panel Power Windows 30 Amp C.B. In Fuse Panel Cigarette Lighter, Flash to Pass and Power Lumbar 20 Amp C.B. In Fuse Panel


29af2f7.gif
e4cf291.gif

May 13, 2009 | 1992 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...