Question about 1997 Buick LeSabre

Open Question

Remove the wiper blade and arm assemblies 2007 Buick lacrosse

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 432 Answers

SOURCE: Resetting wiper arms. Ice damage

Well pop the two little black plastic top hats off of the wiper arm mounts and losen the nuts. Turn your wipers off and tighten them in the lower position.There should be visible mark on the widshield where the wipers have spent most of there time sitting.If you have them to low when you turn them on you will be able to tell by how high the go up on the windshield.Well hope this helped.

Posted on Jan 27, 2010

Ad
  • 566 Answers

SOURCE: how do I compress the rear brake piston on 2007

hi from uk most rear brake calipers have auto adjust mechanism and yours may be the same as on uk models whereas to compress the piston back into caliper to facilitate fitting new pads ? you have to both press and rotate piston and this sends piston back on the screw auto adjuster you will notice that piston has a couple of slots on its head ? this is there for enabling screw back having said this there is a rear caliper piston compress tool that does this job and the cheapest tool and good quality is made by draper tools and costs approx £10 in uk but can be obtained at any good auto stores and has instructions on use well worth the investment ? just one tip pistons normally screw back clockwise however! on fiats? the nearside screws anticlockwise so just observe that piston is going back when rotating c/wise if not you can fit a 3/8" drive extension and t bar to the rotator boss and using pressure ?turn piston a/clockwise hope this helps one word of advice !make sure you bleed brakes afterwards to clear out dirty fluid untill clean fluid shows this will improve brake pedal best wishes from uk

Posted on Mar 23, 2010

  • 3 Answers

SOURCE: how to install/change complete headlight assembly

Buick Lacrosse - The bright light fitting is the same as the dim so take it apart first to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you more space.

Posted on Apr 03, 2010

kapishtech
  • 2272 Answers

SOURCE: Replace headight assembly on 2005 buick lacrosse

The procedure to replace head light assembly on buick lacrosse is as follows:--- 1)To remove and replace the headlight assembly you will need to remove 1 retaining bolt on the top of the headlamp assembly and 2 sliding retainers at the rear. 2) The carefully Pull up the retainers and that will release the headlight assembly and allow you to pull it out the front. 3) When installing the new headlight assembly make sure you have it lined up correctly before trying to install the retainers, don't force them it may get cracked . 4) Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. 5) Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. 6) On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. 7) Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. 8) Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. Note:-- The turn signal is part of the headlight assembly on your 2005 Buick LaCross. 9) To replace the headlight bulb you need to remove the front bumper cover. 10)To release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. 11)To remove these locking pins, pull or pry up the little tab in the center of the pin. Thanks.

Posted on May 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear wiper assembly from the rear wiper motor


flip the nut cover back up the arm and undo the nut shown
the arm base is normally on a splined taper so you may need a flat blade under the arm base on a piece of something so as not to damage the paint and lever it off the spline

Sep 02, 2015 | 2007 Saturn Outlook

1 Answer

Change wipers 1994 buick lesabre


Hi, Where the wiper arm and blade join, depress the clip in the center and slide wiper blade backwards toward arm. Assembly is reverse of removal. Mike

Jun 14, 2011 | 1994 Buick LeSabre

1 Answer

Passenger side wiper blade does not run on 2006 lacrosse


On lower side of wiper arm (closest to windshield) is a nut that has probably come loose. They do this when someone has forced frozen wiper. Tighten nut. It's under a flip up cap

Feb 13, 2011 | 2006 Buick LaCrosse

1 Answer

I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
  1. Turn ignition switch to ACCY position.
  2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
  3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
To Install:
  1. Insert wiper arm hook through opening in wiper blade.
  2. Place wiper blade pivot in the inside radius of wiper arm hook.
  3. Pull on wiper blade pivot into hook until it locks into place.
  4. Check wipers for proper operation.
Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
  1. Remove washer hose.
  2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
  3. Remove wiper arm from shaft.
To Install:
  1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
  2. Press arm assembly on shaft and push retaining latch IN.
  3. Connect washer hose.
  4. Remove windshield markings and check wipers for proper operation.
prev.gif next.gif

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

Windsheild wiper arm on drivers side is off track ,how do i fix it?


Let the wiper work with the blades pulled out of the glass. Now switch off and allow it to park. You can now see the difference in the lefft /right parking.
Remove the arm mounting from the knurlings and set it back to fall just into the correct slot at the bottom of the glass beading.
A corrrection can also be done onthe park switch within the motor assembly but this seems easier.

Sep 17, 2010 | 1998 Buick Century

2 Answers

How to replace rear wiper blade - "07 Hyundai Santa Fe


pull the arm out,towards you ,then press the small tongue on the plastic clip and slide the pastic bit down the arm and off. replacement is a push fit until the clip clicks into place.

Jul 29, 2010 | 2007 Hyundai Santa Fe Limited

1 Answer

Windshield wiper blades stick in upright position when turned off.


yes google this problem and you will find that under the wiper motor is a plate with a metal tab that should be bent @90 degees. over time it bends down and will not contact the oter metal plate on motor.. you need to remove cap holding wiper arms on then remove wiper arm, then remove plastic cowling, the remove plastic cover over motor, then u will see tab bend it back up and u will be fixed. mark wiper arm position on shaft so you assemble in the same position

Mar 04, 2010 | 2001 Buick Century

1 Answer

How do i remove wiper blades on my 1995 buick lesabre?


very simple.

pull the wiper blade up and look at the connector to the wiper arm..you will see a small little tab depress it and pull the wiper blade off the arm

Feb 06, 2010 | 1995 Buick Park Avenue

1 Answer

Replace wiper motor


Wiper Motor
  1. Remove the wiper blade and arm assemblies, as outlined earlier in this section.
  2. Turn the ignition ON and the wiper switch OFF so the wiper motor returns to the park position.
  3. Disconnect the negative battery cable.
  4. Unfasten any necessary retainers and remove the air inlet screen assembly. Disconnect the washer hoses.

e828ab6.gif
Remove the air inlet screen retaining bolts/screws ...


d3d9288.gif
... then remove the air inlet screen


79f8835.gif
Disconnect the windshield washer fluid hose(s)


  1. Disconnect the wiper arm transmission drive link from the crank arm using a suitable wiper transmission separator tool.


9299629.gif
There is a special tool available to separate the transmission drive link from the crank arm


76dac5f.gif
View of the transmission drive link separated from the crank arm

On some vehicles, it may be necessary to remove the nut from the ball crank and remove the crank arm.


7e68234.gif
Location of the wiper arm ball crank


51c4507.gif
If necessary, unfasten the ball crank retaining nut, then remove the crank arm

Detach the electrical connectors from the wiper motor. Remove the wiper motor mounting bolts/screws.

Feb 06, 2010 | 1997 Buick LeSabre

1 Answer

Remove and replace wiper blade assebly 89 chevy silverado


there is a keeper on the inside of the arm. its easier to get to if you remove the whole arm. lift the wiper arm and near the pivot point there is a little flat bar that sticks out along the arm itself. its about a quarter inch long. pull that out alittle and slide the arm off the peg. makes it easier for me. if you cannot get the wiper off still, destroy it. your replacing it anyway and the arm is pretty sturdy.

Jun 03, 2009 | 1989 Chevrolet K1500

Not finding what you are looking for?
1997 Buick LeSabre Logo

Related Topics:

405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...