Question about Ford Territory

Open Question

I want to know how to remove headlamp assy from ford territory 04 SX

How many bolts used to fasten headlamp assembly?

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: headlight assy removal

Hi,
First, you need to remove the front bumper cover, it's held on by clips and screws on top, side and bottom. Then you can remove two bolts on top side of the headlight, also remove the bolt on the side close to the fender, you will see this one once the bumper cover is off. Disconnect the connectors at the back of the headlight, and then remove the light. Sometimes you may have to pull on the lamp housing a little to pop it out from the retaining clip, if not then just wiggle it out carefully. Hope this helps.

Posted on Jun 19, 2008

chuck943
  • 783 Answers

SOURCE: 2002 ford escape passanger side headlamp assembly removal?

Removal and Installation

  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. NOTE: Pull headlamp assembly forward to access electrical connectors.
    Remove the headlamp assembly.
    1. Remove the three bolts.
    1. Loosen the nut.
    • Disconnect the electrical connectors.
    a0045726.gif
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Posted on Mar 03, 2009

  • 1 Answer

SOURCE: i need to replace front headlamp lens peugeot 405 1992

phone the scrapyard you bought it from, they had to take it out and having had your business, will hopefully be helpful!

Posted on Feb 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A HEADLIGHT FROM A 2007 SATURN OUTLOOK XE


Hi Carol , your going to have to remove the headlamp assembly to replace the bulb !


Remove the headlamp assembly. Refer to Headlamp Replacement.



1



Headlamp Bulb Accessory Covers (Qty: 2)



2



Headlamp Bulb Assembly (High Beam)




Caution: Refer to Halogen Bulb Caution in the Preface section.




Tip

Disconnect the electrical connectors and remove the bulbs.



3



Headlamp Bulb Assembly (Low Beam)


Callout

Component Name

Preliminary Procedure

Remove the front bumper fascia. Refer to Front Bumper Fascia Replacement .




Headlamp Assembly Bolt (Qty: 4)

Notice: Refer to Fastener Notice in the Preface section.

Tighten

6 N?·m (53 lb in)







2





Headlamp Fascia Brace Fender Reinforcement Bolt




Tighten

6 N?·m (53 lb in)







3





Headlamp Cam Adjuster




Procedure

Set the headlamp adjusters at the nominal setting of 6 turns off fully seated.







4





Headlamp Cam Locking Nut







5





Headlamp Assembly




Tip

Disconnect the electrical harness as the headlamp assembly is being removed from the vehicle.

Apr 08, 2015 | 2007 Saturn Outlook XE

1 Answer

How to remove headlight assembly on 2013 Dodge Journey


First, you need to disconnect the negative battery cable. Then loosen up the front fascia on the side where you are removing the headlight assembly. Remove the 4 push pins that fasten the upper grille to the FEM (Front End Module). You will then need to push the fascia and grille forward enough so that you can remove the three screws which hold the headlamp assy. to the FEM. Finally, you pull the assy. far enough away from the FEM to reach the headlampand dash wire connectors from the rear of the headlamp housing.

Jul 25, 2014 | 2009 Dodge Journey

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

I am looking for a diagram of the bumper assembly for a 2004 Chrysler town & country.


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


  1. Release hood latch and open hood.
  2. Remove the headlamp assemblies.
  3. Hoist vehicle and support with safety stands.
  4. Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
  5. Remove front wheels.
  6. Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Fig. 1 133387737
Fig. 2 133387738

  1. Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
  2. Disconnect fog lamp wire connectors, if necessary.
  3. Lower vehicle.
  4. Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
  5. Remove bumper fascia from vehicle.
INSTALLATION


  1. Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
  2. Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
  3. Hoist vehicle and support with safety stands.
  4. Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
  5. Install front wheelhouse splash shields fasteners.
  6. Install front wheels.
  7. Connect fog lamp wire connectors, if necessary.
  8. Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
  9. Lower the vehicle.
  10. Install the headlamp assemblies.

Jan 02, 2011 | Chrysler Town & Country Cars & Trucks

1 Answer

How to replace headlight assembly on a 2007 gmc sierra 1500 sle


try t
  1. Remove the radiator grille. Refer to Radiator Grille Replacement.
  2. Loosen only, do not remove, the lower outside hidden headlamp bolt (2).
  3. Pull the lamp assembly slightly forward to access the electrical connection.
  4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
1
Headlamp Screws (Qty: 2)
Notice: Refer to Fastener Notice in the Preface section.
Tighten
Tighten the screws to 6 N·m (53 lb in)
2
Headlamp Screw (Hidden)
Tighten
Tighten the screws to 6 N·m (53 lb in)
3
Headlamp Housing Support
Tip
Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support.
  1. Remove the radiator grille. Refer to Radiator Grille Replacement.
  2. Loosen only, do not remove, the lower outside hidden headlamp bolt (2).
  3. Pull the lamp assembly slightly forward to access the electrical connection.
  4. Disconnect the forward lamp harness main electrical connector from the headlamp harness.
1
Headlamp Screws (Qty: 2)
Notice: Refer to Fastener Notice in the Preface section.
Tighten
Tighten the screws to 6 N·m (53 lb in)
2
Headlamp Screw (Hidden)
Tighten
Tighten the screws to 6 N·m (53 lb in)
3
Headlamp Housing Support
Tip
Depress the housing support tab with a flat-bladed tool downward in order to release the headlamp assembly from the support.
his.

Nov 11, 2010 | 2007 GMC Sierra 1500

1 Answer

I need to change the headlights


REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

  1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
  2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
  3. Pull the headlamp assembly out and away from the vehicle
  4. Disconnect the headlamp electrical connector.
  5. Remove the headlamp assembly from the vehicle.
  6. Remove the headlamp bulb cover from the headlamp assembly.
  7. Remove the headlamp bulb socket from the headlamp assembly.
CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Remove the headlamp bulb.
  2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
  3. Remove the side marker bulb.
  4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
  5. Remove the parking lamp bulb.
INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Install the headlamp bulb to the socket.
  2. Install the headlamp bulb socket to the headlamp assembly.
  3. Install the headlamp bulb cover to the headlamp assembly.
  4. Install the side marker bulb to the socket.
  5. Install the side marker bulb socket to the headlamp assembly.
  6. Install the parking lamp bulb to the socket.
  7. Install the parking lamp socket to the headlamp assembly.
  8. Connect the headlamp electrical connector.
  9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
  10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.
NOTE: Refer to Fastener Notice in Service Precautions.
  1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
Tighten the bolts to 6 N.m (53 lb in).


  1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
  2. Close the hood.
3e4ca4a.gif

Oct 21, 2010 | 2006 Cadillac SRX

1 Answer

Need to replace the headlight assembly on front passenger side do i have to take off the bumper? for ponitac vibe 2003 also have dent on the area


Yes you do. This is the steps to do that to replace the entire headlight assembly:


Remove the front fascia.
  • Remove the front fascia extensions, if equipped.
  • Remove the front fender liners.
  • Remove the fog lamps.
  • Remove the bolts (4) from the front bumper fascia (3) at the fender.


506bafd.gif

Remove the bolts from the front bumper fascia at the fender



  • Remove the push-in retainers (2) from the bumper fascia using J38778.
  • Remove the fascia bolts (1) from the fascia.
  • Remove the fascia from the vehicle.
  • Remove the 3 bolts which secure the composite headlamp.


  • 7f1ec16.gif

    Remove the 3 bolts which secure the composite headlamp



    1. Remove the sidemarker bulb electrical connector.
    2. Remove the sidemarker bulb, if necessary.
    3. Remove the composite headlamp assembly from vehicle.

    To install:

    1. Install the sidemarker bulb to the composite headlamp, if removed.
    2. Connect the sidemarker bulb electrical connector.
    3. Secure the composite headlamp to the vehicle with the 3 bolts. Tighten the headlamp mounting bolts to 89 inch lbs. (10 Nm).
    4. Install the front fascia.
    5. Install the headlamp bulb to the composite headlamp, if removed.
    6. Fasten the headlamp bulb retainer clip.
    7. Install the socket to the headlamp bulb.
    8. Install the rubber cover to the composite headlamp.
    9. Aim the headlamps.
    10. Close the hood.

    Oct 12, 2010 | 2003 Pontiac Vibe

    1 Answer

    I have a 2003 Hyundia Elentra. I had a directional bulb fall out in the headlight case. How can I get it out?


    remove the headlamp assembly (three 10mm bolts). Disconnect the wire harness connector to the assembly. Locate the bulb socket where the directional bulb fell out. Counter-clockwise, twist the bulb socket and remove from headlamp assy. Either return the bulb to its socket, OR replace the bulb & re-insert the socket into the headlamp assy. Reinstall the Headlamp Assy.

    Sep 17, 2010 | Hyundai Motor 2003 Elantra

    1 Answer

    "where is the Horn Location for 2001 Chevrolet Malibu"


    Horn Replacement Removal Procedure
    1. Remove the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.
      794212.gif
      tif.gif
    2. Disconnect the horn electrical connector.
    3. Remove the horn bracket bolt.
    4. Remove the horn from the front frame rail.
    Installation Procedure

      794212.gif
      tif.gif
    1. Position the horn to the front frame rail. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
    2. Install the horn bracket bolt. Tighten
      Tighten the bolt to 10 N·m (89 lb in).
    3. Connect the horn electrical connector.
    4. Install the right headlamp assembly. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement in Lighting Systems.

    May 17, 2009 | 2001 Chevrolet Malibu

    2 Answers

    Need to replace headlight assembly on 2005 Ford Escape


    ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

    n0037234.gif
    Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
    Removal and Installation
    NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
    1. Remove the front bumper cover. For additional information, refer to Section 501-19.
    1. Remove the 3 headlamp assembly bolts.
      • To install, tighten to 5 Nm (44 lb-in).
    1. Remove the headlamp assembly nut and the headlamp assembly.
      • Disconnect the electrical connectors.
      • To install, tighten to 5 Nm (44 lb-in).
    1. To install, reverse the removal procedure.

    Jan 01, 2009 | 2005 Ford Escape

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    2,721 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    fordexpert

    Level 3 Expert

    5474 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...