Question about 2008 Cadillac Dts
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
Posted on Jan 25, 2009
Should be able to open the hood remove plastic headlight cover & pull pins (2) on light assembly whole light assembly will pull out then replace turn signal.
Posted on Dec 02, 2009
Actually no you don't. Crank your steering wheel all the way to the right so yo have the maxumum clearance for your hands and arms in the front of the wheel well. Remove the plastic clips that hold the wheel well splash guard and pull it back enough to allow access to the interior of your bumper.
Replace bulbs as needed.
Yes, a jack is nice and makes it a touch easier to access, but I did this in an AutoZone parking lot during a cross country road trip.
5 mins tops to complete.
Posted on Mar 14, 2010
Remove 3 or 4 of the plastic pins holding the inner fender. They are located around the lip of the fender opening. The pins are removed by pulling the center cap of the pin straight out about an 1/8" and then wiggle and pull the whole pin out.
Pull the inner fender down and back.
Reach your arm in and grab the socket and squeeze the locking tab.
Rotate the socket counter-clockwise less than a quarter turn, and pull straight back.
Reach your other hand in and remove the bulb by pulling it straight out of the socket. It takes a 3157 bulb
Posted on Jun 22, 2010
Testimonial: "Thank you so much for your help. Really I had ask the question about 3 months ago, but since I didn't had it fixed yet, it's OK now. Franco"
SOURCE: 2006 Cadillac CTS Turn Signal
The fender liner needs to be removed. It takes the removal of up to 20 plastic pins. Once it is out of the way the bulb sockets become available. twist the bulb socket counterclockwise and the bulb can be pulled out. Reverse order for reinstallation
Posted on Aug 01, 2010
Tips for a great answer:
Aug 29, 2016 | 2008 Cadillac Dts
Mar 01, 2016 | 2008 Cadillac Dts
Jun 13, 2015 | 2008 Cadillac Dts
Aug 01, 2014 | 2007 Cadillac DTS Sedan
Apr 16, 2014 | 2007 Cadillac DTS Sedan
Mar 04, 2013 | 2004 Cadillac SRX
Mar 26, 2012 | 2006 Cadillac SRX
Oct 30, 2011 | 2007 Cadillac DTS Sedan
Oct 30, 2011 | Cars & Trucks
141 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: