Question about 2005 Chevrolet TrailBlazer LT

Open Question

4.2 liter knock sensor

Need to location of knock sensor for removal and replacement

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: Where is the location of the knock sensor for a 2005 HD 2500 6.0

HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Posted on Jan 26, 2009

Ad
  • 1 Answer

SOURCE: knock sensor location on 2001 chev 1500 4x4 5.3 eng

they are located under the intake manifold, it takes two. they sit in a pint size cup hole. they tend to rust from engine WASH.

Posted on Jul 27, 2009

  • 192 Answers

SOURCE: I have a 1989 Chevy Van, G20 with a 5.7 liter

UNDER NEATH BY THE STARTER

Posted on Nov 08, 2009

  • 14 Answers

SOURCE: knock sensor location

The knock Sensors are located under the Intake Manifold at the top of your engine. The top will have to be taken off along with the intake manifold. Knock Sensors in past silverados used to have a problem with leaking water that corroded the sensors from washing the engine. Most times when you go to replace the knock sensor you will have to replace both along with the wiring harness that includes the the gaskets the knock sensors are surrounded by. After that you have to check the resistance to make sure you dont have any problems and then reinstall all parts along with a new intake manifold gasket. A good mechanic can do this for you in a day and charge you around $400. If you try to go to some place like a chevy dealer you will pay over $800. This is from experience of just replacing mine 2 weeks ago.

Posted on Mar 10, 2010

d_hubbs
  • 270 Answers

SOURCE: how to replace the knock sensor on a 2004

Hello Friend:

Your Anti-Knock Sensor is Located With Hood Raised Facing the Engine Compartment,Its on the LEFT SIDE Right Under your Exhaust Manifold Towards the Back.

On the Engine Block ,You'll see Your Anti-Knock Sensor Wires running to it.

Its a Little hard to Get to but Not so hard that you can't do it Yourself.

Disconnect the Wire Connector, And Take a Good Look at the Wires,Since it Runs so Close to your Exhaust you could have Also some Faulty Wiring going to the Sensor.

Just Un Screw the Anti-Knock Senser and Replace New.

This will get your Anti-Knock Sensor Replaced With A New One Like i Said Look very Good at the Wiring Going to the Sensor.

Thanks for using FIXYA Please let me know how i've helped you by Voting and If you Would write a Small Testamony.

Thank You: From d_hubbs

Posted on Jul 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How. Many. KNock Sensors On 2010 terrain


2010 gmc terrain
https://www.parts.com/index.cfm?fuseaction=store.PartInfo&PartNumber=12621820&VehicleID=208990&diagram=FJ10135&Title%3D-2.4-LITER-KNOCK-SENSOR

1e620784-364d-46a1-a740-60b18a51f685.gif

May 10, 2016 | Cars & Trucks

1 Answer

Knock sensor location on a 2005 dodge Durango 4.7 liter


There are two knock sensors, and they are installed into the block (left and right side) under the intake manifold. The intake manifold must be removed to replace them. They are not identical, and must be installed in the correct position (they are tagged) so that the PCM knows which is which.

Jan 09, 2016 | Dodge Cars & Trucks

2 Answers

Knock sensor diagram


On the 2.4 liter four-cylinder engine it is located on the siie of the engine block (the side nearest the firewall).

On the 3.0 Liter V-6 engine there are 2 knock sensors and the are located in the "valley" below the intake manifold. You'll have to remove the intake manifold to get to them.

Jul 22, 2014 | 2003 Toyota Camry

1 Answer

Gmc Sierra knock sensor???


There a several different engine sizes. The most common is the 5.3 liter. To replace the knock sensors (which will not solve your engine noise at startup) you will need to first remove the intake plenum. That is the part in between the valve covers that the throttle body and the injectors are attached to. Once the intake plenum is removed you ill see the knock sensors bolted to the block.

Apr 12, 2013 | Cars & Trucks

1 Answer

Were is the knock sensor on 2002 protege5 2.0L


The knock sensor is located under the intake manifold to replace do the following
Disconnect the negative battery cable.
Remove the intake manifold.
Disconnect the sensor connector.
Remove the sensor from the engine block.
Installation is the reverse of the removal procedure

Sep 28, 2012 | 2002 Mazda Protege

1 Answer

Cant locate my knock sensors on my chevy silverado 2001 8.1 liter


The knock sensors are under the vehicle on the engine block.One is by the starter and the other one is on the opposite side.You do not have to drain the cooling system to remove them.Hope this helps.Good luck.

Sep 10, 2010 | Chevrolet 2500 Cars & Trucks

1 Answer

Where is the knock sensor located at on my honda odyssey 1999? i cant find it someone help


It is in the inner V of the V-6 at least on my 2000 with 3.5 liter engine. It is towards the front passenger side of the engine. It is located behind the power steering pump and it seems like their are two forum listed techniques for replacement - moving the pump or more likely removing the intake manifold and front fuel rails. Many times it seems to be rodent damage to a wire harness, apparently soy based, rather than the sensor itself. Honda has a new part number to prevent re-eating!

May 13, 2010 | Cars & Trucks

1 Answer

Where is the knock sensor driver side for 2001 pontiac grand prix


Hello! Here is a picture of the location of the front knock sensor for a 3.8 liter V6 3800 Series II (97-03)
(Please note that the engine is upside down on the stand)
There are 2 knock sensors on this engine, one on the front (as shown), and another in the rear. There isn't one on the driver's side, per se.

0038e37.jpg

I recommend that you let the vehicle cool down before beginning this process. To remove this you will need a drip pan, as coolant will leak from the engine when the sensor is removed. You will need a deep well 22mm socket and torque wrench.

1. Jack up and support the vehicle on jack stands so that you can work from underneath the vehicle. Be sure to apply your emergency brake.
2. Identify the knock sensor location and remove the electrical connector on the bottom.
3. Using the deep well socket, remove the sensor from the block. Do not position yourself direcly underneath this, as coolant will begin to flow immediately from the sensor's location.
4. Your new knock sensor should come pre-coated with sealant/threadlock, just install it and tighten by hand until snug.
5. Torque the sensor to 14 ft lbs.
6. Replace the electrical connector.
7. You should flush the entire coolant system to be sure to remove any air pockets, and then refill.


Hope this helps and thanks for using FixYa!

Oct 01, 2009 | 2001 Pontiac Grand Prix

1 Answer

Where is the location of the knock sensor for a 2005 HD 2500 6.0


HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Jan 26, 2009 | 2000 Chevrolet 2500

1 Answer

Knock sensor location


Knock Sensor Description addthis_pub = 'car-suff'; button1-bm.gif parts-box-top-lft.gif parts-box-top-rt.gif knock-sensor.jpg parts-box-rt.gif parts-box-btm-lft.gif parts-box-btm-rt.gif A quality Knock Sensor is more important than ever thanks to today’s increasing gas prices. Your Engine Knock Sensor enables your vehicle to obtain the optimum combination of timing and fuel/air mixture to generate power and efficiency and that means less wasted gas. Our guaranteed low prices make us your one-stop Knock Sensor Location. Regardless of the brand, make or model car, truck, van or SUV you drive, we make it easy to locate the application specific Knock Sensor that’s perfect for your vehicle. Our state of the art parts locating system puts you just a few mouse clicks away from the Knock Sensor you need and at a price you cannot beat anywhere. Click. Click. Click. And you are there. In addition to robbing you of fuel economy and performance a faulty Knock Sensor can cause expensive damage to your engine. Remember, the Knock Sensor keeps fuel from detonating in the cylinder … exploding rather than quickly burning as it should. If not replaced a faulty Knock Sensor can quite literally cause hundreds if not thousands of dollars in damage. There is really no need to look any further to find the Knock Sensor that’s application specific for your car, truck, van or SUV – high performance or family vehicle. We’ve got guaranteed low prices and shipping that other suppliers envy. Give us a try, we think you’ll be happy … in fact we guarantee it.

Jun 20, 2008 | 2003 Hyundai Santa Fe

Not finding what you are looking for?
2005 Chevrolet TrailBlazer LT Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...