Question about 1990 Toyota 4Runner

Open Question

How to install parking brake cable on 1990 toyota 4 runner

E cable needs to be replaced

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: replace front brake pad 2003 toyota 4 runner

Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers

Posted on Mar 25, 2009

Ad
steve_baldam
  • 52 Answers

SOURCE: '96 Toyota 4-Runner makes a loud squealing noise and brake light

Sounds like one of the auxillary belts slipping it may just need tightening up. I think the 4-Runner has two belts one large and one for the steering pump

Posted on May 13, 2009

  • 49 Answers

SOURCE: cant bleed out brakes

It takes time, do you know the sequence to bleed the brakes? Most cars r different. And you have to keep pouring brake fluid, That is a two person job. Make sure all lines r connected to MC and not leaking. After a while if nothing comes out MC could be diffective.

Posted on Jun 06, 2009

  • 1810 Answers

SOURCE: window will not roll up on 1990 toyota 4 runner

no power or no ground ??
try running a hot line to the motor

run a pair of wires from the batterie 1 pos 1 neg speaker wire will do

unplug the window motor and run it direct pos on 1 wire neg on the other flip the wires to change motor direction
if motor works then it's eithor a bad ground or a bad wire or a bad reley

Posted on Jan 01, 2010

  • 1 Answer

SOURCE: Replaced rear brakes, Alarms still active

i have a 2003 toyota 4-runner my brake and abs vsc are on and it has a beeping loud noise.....what do u think is the problem?

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 toyota 4 runner the blower for my heater does not blow all fuses good but is there a connector fuse somewhere


replace the blower assembly, there may be a short in the cabling where it connects to the engine

Nov 08, 2011 | 1990 Toyota 4Runner

1 Answer

1990 Toyota 4 runner How do I replace brake light bulb?


which brake light? if it is in the sides, drop the tailgate/back door and remove the screws holding the tail light assembly in and then it should just pop out. If it is a 3rd brake light, 2 screws hold the cover in and remove those and carefully pry the plastic cover out and gently pull on the bulb

Feb 04, 2011 | 1990 Toyota 4Runner

1 Answer

Problems with my toyota 1990 4 runner 3.0 I


get the water pump and thermostat changed

Sep 02, 2017 | 1990 Toyota 4Runner

1 Answer

Does truck have to be running on my 1990 toyota 4-runner 4x4 ?


No, you can do it without the engine running. The power assist just makes braking easier. Just make sure you don't move the pedal till the bleeder is tight, then pump it back up an do it again. Start at the right rear and move towards the front left. Hope this helps.

Jun 16, 2010 | 1990 Toyota 4Runner

1 Answer

1995 4 runner automatic 6cyl. Replaced selenoid on brake pedal but it still wont shift out of park. Have been release button past week


have u checked the brake light bulbs some models have a safty thing if brake lights ot it wont come out of park

Oct 05, 2009 | 1995 Toyota 4Runner

1 Answer

My 1990 toyota 4 Runner has a v low rpm while in


on the cable of the accelerator,there is an adjuster to its an,so you can adjust it here to rev it a little ,at 750 rpm,

Aug 19, 2009 | 1990 Toyota 4Runner

2 Answers

Cant bleed out brakes


It takes time, do you know the sequence to bleed the brakes? Most cars r different. And you have to keep pouring brake fluid, That is a two person job. Make sure all lines r connected to MC and not leaking. After a while if nothing comes out MC could be diffective.

Jun 06, 2009 | 1990 Toyota 4Runner

1 Answer

'96 Toyota 4-Runner makes a loud squealing noise and brake light


Sounds like one of the auxillary belts slipping it may just need tightening up. I think the 4-Runner has two belts one large and one for the steering pump

May 13, 2009 | 1996 Toyota 4Runner

1 Answer

My 2000 4 runner won't shift into park


sounds like a faulty selector cable/rod as park and reverse are next to each otheron selection, it may just require lubricating.

Feb 02, 2009 | 2008 Toyota 4Runner

Not finding what you are looking for?
1990 Toyota 4Runner Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...