Question about Toyota Camry

Open Question

1994 toyota camry 2.2lt.ignition coil replacement

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: Correct Firing Order for 1994 Toyota Camry 2.2L 4 cyl.

1-3-4-2

Posted on Jan 21, 2009

hotratchet
  • 952 Answers

SOURCE: need to replace the thermostat in a 1994 Toyota Camry

1. Look up along the lower radiator hose. It will plug into a metal tube on the engine side. Follow the metal tube. It goes to a housing. The housing is kind of buried in the driver's side of the engine. There are 2 smaller coolant tubes plugged in above it. You do not need to touch those, although it looks at first glance like you do.
2. Disconnect lower radiator hose at the metal tube.
3. Disconnect fan switches 1 and 2. These are on elecrtical harnesses going to this housing.
4. Disconnect a sensor on the front of the engine, just above the lower hose. I believe this is the knock sensor, but I'm not sure.
5. Now for the fun part. There are 3 bolts holding this housing on. You can see one at the top. There are 2 others underneath it, such that the bolts form a triangle pattern. You will have to get the bottom 2 out by feel (blind). They are 10mm.
6. Also, if you look to the front of the housing, you will note another 10mm bolt on the front holding down a black plastic leg. This is a wiring harness duct. Remove that bolt. Trace back along the duct. There is one more bolt on the driver's side retaining the duct. There is also one on the back of the engine at the firewall / driver's side. Remove these 2 as well.
7. There is a 12mm bolt holding the metal tube from that housing to the driver's side. Remove that bolt.
8. Gently pry the plastic wiring duct toward driver's side, and back toward firewall. You have just enough to get it off of the stud on the thermostat housing.
9. Now you can pull the housing. It will not come all the way out. It will come loose enough to give you just enough clearance to remove the thermostat (barely). Once you remove the thermostat, you have to pass it downward and toward the firewall to fumble it out.
By the way, you will notice that the metal tube is kind of wiggly in the thermostat housiung. This is normal.
10. Pass the new thermostat in the same way you got the old one out. Make sure when you plug it in that it has an air bleed poppet, and that this poppet is facing up.
11. Reassemble by reversing removal. Getting the nuts / bolts back in blind is... fun...
I don't know the torque spec. You can get a torqure wrench in there barely if you get creative with extensions, knuckles, etc. I wouldn't go abouve 8-10 ft-lb.

Posted on May 01, 2009

rockitman187
  • 2559 Answers

SOURCE: How much freon does the 1994 Toyota camry hold?

Refrigerant Type R-134a Amount 30oz
Oil Type PAG-46 amount 8 oz


Please take time to rate this fixya

Posted on May 15, 2009

  • 30 Answers

SOURCE: 1994 toyota fuel pump relay

Fuel pump relay is in the engine compartment left side fuse block

Posted on Jul 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1994 camry 2.2 engine when car warms up engine shuts off and wont start let it sit for about 20min and will restart runs great when cold could this be ignition coil inside distributor


Inspect the coil for cracks or signs of shortage!! Also if there is oil leaking into the distributor, this will cause the coil to burn.

Jun 12, 2011 | 1994 Toyota Camry

1 Answer

How can I tell if the ignition switch is bad in my toyota camry?


You need a tachometer compatible with the Toyota Camry's ignition system. Start up the Camry's engine and let it reach normal operating temperature. Connect the tachometer tester probe to terminal IG of the Data Link Connector 1. Connect terminals TE1 and E1 of the DLC1 with a jumper connector. Inspect the tachometer's timing. It should be between 8 and 12 degrees Before Top Dead Center. Set the timing as necessary. Tighten the hold-down bolt and make sure the ignition timing advances. Ignition Coils Disconnect the negative terminal from the Camry's battery. Remove the two nuts and clips on top of the cylinder head cover, then remove the cover. Disconnect the four ignition coil connectors and the bolts retaining the coils. You can now remove the coils. Replace the coils as needed. Connect the bolts and coil connections and replace the cylinder head cover.

Aug 31, 2010 | 1999 Toyota Camry

1 Answer

94 toyota camery 4 cyl wont start Ichecked the fuel injectors there ok checked fuel pump works fine replace distributor cap and the ignitor but I dont get a spark at the sparkplugs.henrys


check all efi and ign fuses first...then check pickup coil and ignition coil in distributor w/ ohm meter...since you already replace the ignitor, then mostly likely it's the pickup coil or ignition coil...buy the whole

Aug 22, 2010 | 1994 Toyota Camry

1 Answer

1994 camry will stall while driving normal speeds. Check engine light and airbag light comes on. Vehicle will start immediately but lacks power and misfires. After cool off vehicle will perform properly...


4cyl or V6?? Have your ignition coil checked and you vehicle scanned for the check engine light. If this is a 4cyl the coil is inside the distributor cap (possible oil leaking into the cap, very common on 4cyl camrys). If its a V6, have the Crank and cam sensors inspected. Hopefully this helps!!

Mar 16, 2010 | 1994 Toyota Camry

2 Answers

Toyota camry 1994 220 sei, non start


Replace the ignition coil under the distributor cap.
Common problem.

Aug 11, 2008 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...