Question about 2002 Chevrolet Monte Carlo

Open Question

Intake gasket on a 2002 monte carlo

How to replace the intake gasket

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Oil in over coolant tank

since you are running green coolant in a car designed for dexcool that may have contributed to a leaky intake gasket and/or head gasket. dexcool was specially formulated to run in the GM vehicles because the gaskets and seals can be easily distorted when the wrong chemicals are soaking them. oil in the coolant is usually either a head gasket or the lower intake manifold leaking into the cooling system. also if the intake gaskets werent done properly that would cause oil in the coolant as well. i suggest you take your car to a reputable shop and have it tested for a headgasket leak and to have the lower intake inspected.

Posted on Feb 17, 2009

ginko
  • 19396 Answers

SOURCE: 2002 monte carlo ss

The fuel filter is located in the pressure line that runs from the fuel tank to the engine, near to the fuel tank.
Keep the engine off for few hours before replacing the filter, to get rid of some pressure in the lines.

Posted on Feb 27, 2009

  • 401 Answers

SOURCE: my 2002 monte carlo`s fuel gauge fluctuates from full to empty

Hi you need a fuel level sensor

Posted on May 13, 2009

  • 78 Answers

SOURCE: 2002 monte carlo radio code needed

basicaly if you dont got the code card you have to remove the stereo and behind the stereo is a serial number that the dealer will give you the code number but the deal is tha they charge ten to twenty dllrs kind of bites but you will have a working stereo

Posted on Jun 03, 2009

  • 6982 Answers

SOURCE: replac 2003 monte carlo oil pan gasket

To remove the oil pan on any vehicle, first remove anything obviously in your way...starter, exhaust pipe etc. Then disconnect the engine mounts and raise engine to gain sufficient clearance between frame and pan. You cannot support the engine from under the pan so either use a fixture above the engine or put blocks between mounts and engine to support it. After all rail bolts have been removed, remember that the oil pump pickup will interfere with removal somewhat but pan can be maneuvered around it. Anything preventing you from getting the pan out will then need to be removed or moved as they are identified. Be careful when raising the engine that you do not break anything above it as it comes up.

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why water mix with the oil in a 202 monte carlo ss 3800 engine


you have a blown head gasket or leak at the intake gasket 9 out of 10 it the head gasket good luck....

Oct 31, 2012 | Cars & Trucks

2 Answers

How to replace a thermostat on a1998 Chevrolet Monte Carlo 3.1 v6


you may be able to take off the water housing by taking the front bolt out and loosening the rear, but its TOUGH to get too. A repair shop can do it for you. I replace them if I have the intake manifold off for any reason. check if intake gaskets are leaking,(common), then you need them replaced and the thermostat is easy to replace at that time.

Aug 04, 2011 | 1998 Chevrolet Monte Carlo

2 Answers

I have coolent leaking into the oil. Suggest that I have an intake gasket problem. Besides changing the gaskets is there a replacement intake for 2000 Monte Carlo?


There should be no reason to change the intake itself,just the intake gasket,be sure to torque the bolts to specs,and you will have no problem in the future.

Sep 08, 2010 | 2000 Chevrolet Monte Carlo

1 Answer

Leaking coolant


You need to replace the lower intake manifold gaskets

Mar 31, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

EGR VALUE HOW TO REPLACE ON 1998 MONTE CARLO W3100 ENGINE ?


there is 2 10 mm bolts and a wiring harness to unplug right beside the intake . make sure the gaskets are in good shape

Sep 23, 2009 | 1998 Chevrolet Monte Carlo

1 Answer

95 Monte Carlo Idle Fast and Have low oil pressure


95 monte carlo is idling high we just replaced the intake manifold gasket. How do I fix this and could I have caused it.

Jun 13, 2009 | 1995 Chevrolet Monte Carlo

2 Answers

Overheatin loosin water and steamin from the back of motor around the intake


You need to have the intake manifold gaskets replaced This will also allow the temp sensor to tell the computer that it has warmed up. Then you can accellerate properly. Good luck Moe

Apr 24, 2009 | 2001 Chevrolet Monte Carlo

1 Answer

95 chevy monte carlo vac leak


It sounds like the Intake Gasket may have slipped a little During the Install. This would cause the Preassure Problem. Let me know so we can go further if needed. Please Rate my Response, I need all the Help that I can get! Thanks!

Jan 26, 2009 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
2002 Chevrolet Monte Carlo Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...