Question about 2007 Mitsubishi Endeavor

Open Question

Lite on lower left corner of dash green key shaped what does it mean

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

There is funny shape light in the dash board, "what does it mean?"


How would someone know what funny shape means

If you have no owners manual google dash board symbols

When you turn on the key you should see & know every
symbol on the dash
After the engine starts they all should be off or you got problems

Mar 01, 2013 | 2002 Mercury Sable

1 Answer

Acwillowno dash lights


dash lites are on a fuse in fuse block under drivers side.
make sure you did not turn the headlight switch all the way off.
it turns or rotates to the left and right to lower the dash lights.

Feb 10, 2011 | 1995 Pontiac Bonneville

1 Answer

How do I set car to be on 4x4?


I believe that Mitsubishi has one of the best and easiest 4X4 selector systems on the Pajero/ Montero. Just below the gear shifter lever is the 4X4 mode selector. A lever like the gear shifter that works in a up, down movement. On your dash board you will notice a sort of axle, chassis diagram in green light. In normal 2WD or 2H mode the lever is set all the way back and on the dash only the rear wheels a lite up in green light on the axle, chassis diagram. This is for normal driving on the highway and smooth roads of dry dirt roads. Pushing the lever up wards while moving at crawling speed will engage the light 4X4 mode which is 4H for when the driving gets a little slippery. All 4 wheels on the axle/ chassis diagram will be lite green. Shifting the lever from the 4H position to the left and upwards will engage the 4HLc mode for 4X4 on sand and deep snow. This will also engage the central diff lock which will show on the axle/ chassis diagram on the dash board with the center box also lite up. Further up from the 4HLc mode and while pushing down on the 4X4 lever push it to the top most position, but only do this when at a stand still with your foot on the brake pedal. This will engage the 4LLc mode with 4X4 and central diff lock on for when driving gets sweaty on thick mud up and incline. To disengage this mode stop, foot on break put it in P and then pull down the lever to one of the lower settings.

Jan 13, 2011 | 1997 Mitsubishi Montero

1 Answer

How do i reinstall the stereo


The instrument panel cover (and therefore the radio bezel) is fastened to the dash frame with snap-clips which cannot be seen with the instrument panel cover installed. To remove the instrument panel cover and gain access to the radio cavity, remove the radio fuse from fuse panel located on the driver's side of truck (the one that has a thumbnail opening and is triangular shaped), visible when you open the driver's door. Then set parking brake all the way down, put key in ignition and turn to "on" but not "start" and put gearshift into "L" position.
The snap-clips are located at the upper right corner, lower right corner, upper left corner, lower left corner and a few places in between, behind the dash cover over the instrument panel. You don't need any tools, just put your fingers on the seam of the dash cover and the the dash body, and pull firmly toward you until the instrument panel cover pops out and GENTLY so as not to break the instrument panel cover, continue until the instrument panel cover is loose from the dash and resting on the steering column. The headlight switch, and 4X4 switch (if equipped) remain in the instrument panel cover and will have to be unplugged to remove the instrument panel cover from the dash completely. This is a snug fit, even with the gearshift in "L".
The aftermarket radio bezel will have two screws at the bottom under the radio on the dash frame. Remove these screws, and remove the aftermarket radio from the radio cavity in the dash. The factory radio has two guide pins on the back, and the electrical connector is made into the radio and again in the back of the radio cavity. Simply slide the factory unit into the radio cavity, firmly seat it into the connector and guide pin sockets, and re-install the two screws you took out earlier.
The instrument panel cover re-installs the reverse of removal, and to seat the snap-clips, simply strike the cover sharply with the heel of your hand over each clip location. The dash will pop right back into place, and you will never know that an aftermarket head unit had ever been in there.

Feb 14, 2010 | 1997 Chevrolet Tahoe

4 Answers

Dash board green indicator light gone to yellow why


yes what does it mean mine is green is that good

Jul 02, 2008 | 1992 Honda Accord

Not finding what you are looking for?
2007 Mitsubishi Endeavor Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...