Question about 2003 Chevrolet Impala

Open Question

Replace Right side Rocker panel trim - 2003 Chevrolet Impala

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 09 pontiac g6 the speakers cut in/out regularly and someone told me to check the factory amp in the trunk but i cant seem to find it i dont think my car has one or is located elsewhere help


What is your G6 coupe or sedan or convertible ?
Radio Speaker Amplifier Replacement (Coupe and Sedan)
Remove the rear compartment trim panel. Refer to Rear Compartment Side Trim Replacement - Right Side.
If it isn't there you don't have one . Check connections at the radio ! Connections OK replace the radio .
--------------------------------------------------------------------------------
Radio Speaker Amplifier Replacement (Convertible)
Remove the rear compartment trim panel. Refer to Rear Compartment Front Trim Panel Replacement.

Jul 01, 2016 | Pontiac Cars & Trucks

2 Answers

2006 Pontiac grand prix where is the blend door actuator mode at




  1. Remove the right instrument panel (I/P) insulator. Refer to Instrument Panel Insulator Panel Replacement - Right Side in Instrument Panel, Gages, and Console.


  2. Remove the I/P compartment. Refer to Instrument Panel Compartment Replacement in Instrument Panel, Gages, and Console.

    alt="Object Number: 1194925 Size: SH">



  3. alt="Click here for detailed picture of above image.">


  4. Remove the screws that secure the mode actuator (1) to the HVAC module assembly.


  5. Remove the mode actuator from the HVAC module assembly.


  6. Disconnect the electrical connector from the mode actuator.



a+2saweek5chaaaaaelftksuqmcc



Instrument Panel Insulator Panel Replacement - Right Side



Remove 3 fasteners. Rotate the lamp. Remove the lamp from the insulator. Remove the insulator.



Instrument Panel Compartment Replacement



Using the finger opening, remove the access hole cover from the right instrument panel (I/P) compartment



Pull the I/P outboard trim plate rearward in order to release the retainers. Remove the I/P trim plate. Open the I/P compartment



Disengage the compartment door stop using the following procedure:







5.1.





Press the upper door stop (2) toward the center of the vehicle.














5.2.





Rotate the door away from the compartment.








Pull the I/P accessory trim plate rearward slightly for access to the I/P inboard trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement .

alt="Object Number: 929399 Size: SH">

Jan 12, 2016 | Pontiac Cars & Trucks

1 Answer

2006 Tahoe. Where is the auxiliary blower motor located?


It is located behind the right rear quarter panel , In the back right of the interior !
Remove the right rear quarter trim panel. Refer to Rear Quarter Trim Panel Replacement - Right Side in Interior Trim.
Removal Procedure
  1. Remove the rear seat. Refer to Rear Number 2 Seat Replacement or Rear Number 2 50-50 Seat Replacement in Seats.
  2. Remove the Third Pillar trim panel. Refer to Third Pillar Trim Replacement .
  3. Remove the garnish molding. Refer to Body Rear Corner Garnish Molding Replacement .
  4. Remove the door sill plate. Refer to Liftgate Door Sill Plate Replacement .
  5. Remove the quarter panel trim screws.
A lot involved in this but not to difficult !
  1. Remove the rear door sill trim plate. Refer to Front Side Door Sill Plate Replacement or to Rear Side Door Sill Plate Replacement .
  2. Remove the lower rear seat belt cover and bolt.
  3. Remove the trim panel from the vehicle.
Remove the sill plate. Firmly pull the sill plate up and out from the retainers.
Remove the sill plate from the vehicle. Start from the front of the door sill. Use a flat-bladed tool in order to pry the door sill plate.
Rear Side Door Sill Trim Plate Replacement
Use a flat-bladed tool in order to pry the door sill plate. Remove the sill plate from the vehicle.
Body Rear Corner Garnish Molding Replacement
Remove the rear upper garnish molding. Refer to Rear Upper Garnish Molding Replacement .
Pull down on the upper corners of the garnish molding in order to disengage the retaining clips. Pull in order to disengage the remaining retaining clips. Remove the rear corner garnish molding from the vehicle. Inspect the rear corner garnish molding for broken or missing retaining clips. Replace the retaining clips as needed.
Good Luck ! Fun job !!!!!

Jun 07, 2015 | 2006 Chevrolet Tahoe

1 Answer

Where is the fuel reset button on a nubria deawoo


Remove the passenger side front rocker trim panel. Remove the lower B--pillar trim panel. Reposition the carpet. There is the fuel cutoff inertia switch with reset button.

May 01, 2014 | 2001 Daewoo Nubira

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

How do I replace a side mirror chevy corsica?


Please don't forget to rate....thanks:


Removal & Installation The door outside mirrors are stud mounted to the door filler. The mirror glass face may be replaced by placing a piece of tape over the glass then breaking the mirror face. Adhesive back mirror faces are available. Left side flat and right side convex mirror faces must be replaced with the same type mirror face when surfaced.
  1. Remove the door trim panel.
  2. Remove the upper trim panel.
  3. Remove the sound absorber.
  4. Remove the (3) nuts.
  5. Remove the control cable from the upper trim panel.
  6. Remove the filler and mirror.
To install:
  1. Place the filler over the studs on the mirror.
  2. Install the control cable through the filler and connect to the upper trim panel.
  3. Install the (3) retaining nuts and tighten to 42-72 inch lbs. (4.7-8.1 Nm).
  4. Install the sound absorber, upper trim panel and trim panel.

Mar 06, 2010 | 1996 Chevrolet Corsica

1 Answer

Need to replace right brake light. How do I remove and replace trunk lining to get access withou doing damage to the liner? What is the correct lamp?


Remove the luggage compartment rear trim panel. Detach luggage compartment side trim panel. Detach the rear lamp assembly bulb holder. Remove the rear lamp assembly. To install, reverse the removal procedure.

Aug 03, 2009 | 2003 Jaguar S-Type

1 Answer

Remove right front fender on 2005 odyssey


NO 2 BOLTS ON TOP OF FENDER UNDER HOOD 1 BOLT BEHIND PLASTIC TRIM BY MIRROR PULL THIS PIECE BACK TOWARDS MIRROR OR IT WILL BREAK TABS OFF 1 BOLT UNDER ROCKER TRIM 1 SCREW INTO ROCKER AND 1 SCREW BEHIND PLASTIC SHROUD GOING INTO BUMPER FROM UNDER NEATH PULL BUMPER BACK SLIGHTY AND YOU WILL SEE A WHITE PLASTIC CLIP PULL BACK AND BEHIND THIS IS A BOLT REMOVE HEADLIGHT CLIP FROM FENDER AND LOSEN BOLT BY HINGE NOW FENDER SHOULD COME RIGHT OFF BOOK IS 2 HOURS TAKES 1 HOUR TO REMOVE BUT GOES ON IN ABOUT 30 NINUTES

Mar 16, 2009 | 2005 Honda Odyssey

1 Answer

Side mirror of 2005 ford explorer


Exterior Mirror Removal and Installation
All vehicles
  1. NOTE: Left side exterior mirror shown, right side similar.
    Remove the interior door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the inside door handle bezel from the trim panel.
  1. Remove the window switch assembly.
  1. Disconnect the window switch and power door lock electrical connectors.
  1. Remove the upper trim panel screw at the window switch opening.
5c94a3e.gif
  1. Remove the lower trim panel screws.
2de1016.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, do not pull directly outward for this step.
    Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  1. Disconnect the power mirror electrical connector.
  1. Remove the trim panel.
  1. Remove the weather shield.
Vehicles with power, heated or approach lamp equipped exterior mirrors
  1. Disconnect the electrical connector.
All vehicles
  1. Remove the bolts.
a2275a5.gif
  1. Remove the exterior rear view mirror (17682).

Feb 23, 2009 | 2003 Ford Explorer

1 Answer

Front fender removal


Hiya... here's the details of fender removal/installation:
the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
The bolt location:
3 are on the top fender-easy to find when hood is open,
1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
**note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
Be sure to exercise care when handing this task!

808b156.jpg

Nov 20, 2008 | 2005 Chevrolet Equinox

Not finding what you are looking for?
2003 Chevrolet Impala Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...