Question about 1991 Mazda 626

1 Answer

Mazda 626 1991 trasmission probleme

Hi ! i found a problem with my mazda since 1 year, as i can just move it on REVRES and when i put it on position D and i push the gas i hear the engine scream like if it in N and can't move the only way i can move is REVRES !!! lol anyone have a solution. THANKS all

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 6,982 Answers

Likely some version of ecat trans right? If so, those units pretty much self destruct If fluid smells burnt & has tiny metal flakes in it you need a new one!

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to find out where the crankshaft sensor is located on Mazda Tribute 2002? Need to change it


2004 Mazda tribute 2.0l manual transmission cranks position sensor tip worn / rubbing. p0351, p0352, p0500, p0320 codes. I have a 2004 Mazda tribute with 2.0l 4 cylinder. 140,000 miles. First problem was it would not start but I could hear the fuel pump run and the engine cranked over. I checked for spark and all four plugs had no spark. p0351, p0352, p0500, and p0320 codes displayed.
I have 12 volts at coil. I decided to remove and inspect crank sensor on the transmission side of the engine ( on engine below thermostat housing bolted to engine block) once i removed it i noticed the tip of the sensor was broken, yes, broken. so I knew i found the problem.
I put a new crank sensor in and the car started but ran for 1 hour idling as if a cylinder was not firing. Then it would not start ever again. I removed my brand new replacement sensor to find the tip was rubbed off enough to see the inside metal. i think it could be a possible warped flywheel but I am having trouble finding diagrams of the excitation part of how the crank position sensor works.
I believe the flywheel has holes that excite the sensor. The tribute does move and clutch works for the hour I had it running, so the manual Trans does work as well as the clutch.
https://electronicshelponline.blogspot.com/

Jul 16, 2016 | 2002 Mazda Tribute

1 Answer

The trasmission is stuck in park. is there a safety switch?


86394771
  1. Remove access hole cover by unfastening screw.
  2. Turn ignition key to "ACC" position and move shift lock solenoid rod (or manual release plate) toward rear side of vehicle by using screw driver or the like.
  3. In this state, select lever can be moved to any range or position.

Mar 02, 2011 | 2000 Suzuki Grand Vitara

1 Answer

My daughter has bought a mazda 2 during the month of october of last year. after about a month, the dashboard lights has gone very very dim. any solution for this problem


Check the dimmer switch position or possibly you have a bad dimmer for your instrument panel lights could be found with headlight switch knob or a separate adjustment on dash.

Feb 06, 2011 | Mazda MAZDA2 Cars & Trucks

1 Answer

Rebuilding 1995 honda civic transmission


Did you make sure that the tork converter was all the way forward first if not then you will need to take the transmission back out and make sure that the converter has either automatic trany fluid in it or 184/85 gear oil depending on whether or not you have automatic trasmission or manual fill it up until you can put your finger in it and then rotate converter clock wise and it should slip into place before putting trasmission back into car and if after doing that and you still are having trouble take it to a transmission shop to have them do it for you.

Sep 14, 2009 | 1995 Honda Civic

1 Answer

The bonnet on my mx5 is high on one side


Found the problem one of the bonnet hinges was beginning to seize up put loads of wd40 on it moved the bonnet up and down to ease the oil in. Then closed the bonnet and pused down on it where the hinge is so that it became level with the wings. I then just loosend the bonnet nuts slightly closed the bonnet and moved it into the best position carefully opend it and did up the nuts if the headlamps are still a bit low open the bonnet and just pull gently on the back of the head lamp and they wil come into place job done it looks great

Mar 21, 2009 | 1996 Mazda MX-6

1 Answer

Mazda mx5 p reg


put some oil on it and let it soak in for a day or so

Aug 09, 2008 | 1996 Mazda MX-5 Miata

3 Answers

Honda crv transmission?


if your trans fluid is full it may be an internal problem in the gearbox even in the converter its hard to diagnose without seeing the car but i can sure try to help if you can add any other noises or symptoms i will see if i can help you pinpoint the problem

May 16, 2008 | 2005 Honda CR-V

Not finding what you are looking for?
1991 Mazda 626 Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...