Question about Cars & Trucks

Open Question

Why will toyota 2kd not start/no rail pressure and no injector pulse

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 142 Answers

SOURCE: 1991 oldsmobile cutlass supreme

Check for fuses/power/ground to the engine computer (or injector drive computer) whatever the case is.

Spark, fuel pump, and starter all are independant of the fuel injection computer.

Either the computer itself has gone bad, or it is not receiving power or ground, or wiring to the injectors might be bad...

Posted on Aug 28, 2008

johnny5846
  • 379 Answers

SOURCE: no injection pulse

looking at the schematics, well the PCM controls the pulse width to the injectors , BUT , there is a injector coil fuse , its #2 in your kick panel fuse box , a 20 amp , check it , sure hope that fix ya . that would be sweet .

J5

Posted on Jan 15, 2009

Molson02536
  • 3854 Answers

SOURCE: 1985 corvette no pulse to injectors

Very important that if you are not savvy of working on your Vette ...you would be better off - taking your car to a dealership for repairs on your trouble codes. However if you feel that you want to, First locate your car's alcl this component is located just below the instrument panel and to the left of the center console. Remove the plastic cover the first two slots to your right are the A & B slots.
The A slot is the diagnostic slot and the B slot is the ground slot. Insert the computer key into these slots if you do not have a computer key, a paper clip or wire jumper clip will do, (with the engine off) this is very important...now only put the ignition key to on ( not start !!!) the check engine light will display a code 12 which is one flash followed by two flashes. This code will be flashed three times ..followed by the trouble code stored in your car's computer.

What ever the code is it will be flashed three times. Have a paper and pencil ready and write down the code.

Code #12: Normal No Codes. 
Code #13: Open Oxygen Sensor Circuit. 
Code #14: Coolant Sensor Circuit Low.
Code #15: Coolant Sensor Circuit High. 
Code #21: Throttle Position Sensor High. 
Code #22: Throttle Position Sensor Low. 
Code #23: Manifold Air Temperature Circuit High.
Code #24: Vehicle Speed Sensor. 
Code #25: Manifold Air Temperature Circuit Low. 
Code #32: EGR System Failure. 
Code #33: Mass Air Flow Sensor High.
Code #34: Mass Air Flow Sensor Low. 
Code #36: Mas Air Flow Sensor Burn-Off Function Fault. 
Code #41: Cylinder Select Error. 
Code #42: Electronic Spark Timing.
Code #43: Electronic Spark Control. 
Code #44: Lean Exhaust indication. 
Code #45: Rich Exhaust Indication. 
Code #46: Vehicle Anti Theft Fault. 
Code #51: Faulty Mem-Cal. 
Code #52: Fuel Calpak Missing.
Code #52(1990-91 Corvette Only): Engine Oil Temperature Sensor Low. 
Code #53: System Over Voltage. 
Code #54: Fuel Pump Circuit Low Voltage. 
Code #55: Defective ECM. 
Code #62: Engine Oil Temperature Sensor Circuit High.

Please remember that if you have the computer key installed in the alcl and you start the engine (you will ruin the engine's computer) only put the ignition to on (not to start).

If you should get a check engine soon display.. you can use the above procedure and codes to buy the right part or at the very least to keep from getting taken for a ride and be made to pay hight prices for some inexpensive module that you could have installed yourself.

If your engine displays a trouble code ... your engine will go into limp mode ..it will still run but very poorly. You might be able to reset the computer if it will not start (just to get home) by disconnecting both battery cables and re-installing them ...this is not recommended ..but if you are stranded it might help unitl you get your car home or to a repair shop..good luck.

Good luck and hope this helps. 

Posted on May 08, 2009

  • 740 Answers

SOURCE: 1993 honda accord 2.2,no injector pulse

This sounds like a main relay problem here is a diagram its located under the dash under steering column its the brownish -orange box in the picture. http://www.tegger.com/hondafaq/mainrelaylocation/7-main_relay_closeup.jpg Good luck and thanks for using FIX YA

Posted on May 15, 2009

Molson02536
  • 3854 Answers

SOURCE: 1993 s10 2.8 tbi the fuel pump fails to pressurize

There needs to be 60 PSI of fuel pressure in the system to have the fuel injectors to work. There is also a fuel pump relay on the fire wall just left to the brake booster, There is two relays there, i just can not remember which relay is which but try switching the relays with one another. Also check the fuses to the fuel pump and ECM, and the fuel pressure from the shredder valve. Good luck and keep me posted, not a bad Idea to also replace the fuel filter, and that is located at the inside frame rail under the drivers side.

Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Toyota Corolla cranks will not start. Has spark, fuel pressure at rail, no injector pulse with noid light when cranking. MIL light very dim. Unable to retrieve fault codes


Check distributor rotation to ensure good timing belt. If good, check crank and cam position sensors. The computer fires the plugs and injectors based on many factors but most importantly the crankshaft and camshaft position.

Jan 24, 2017 | Toyota Corolla Cars & Trucks

2 Answers

2005 2KD Hiace, starts lazy,revs good when it starts but accelerator goes dead, check light comes on, then in about 2 minuets the engine dies. 093 code.


fault code is missing a letter and first number
so its P0093 large fuel leak

the fault list has list of what to check
http://www.obd-codes.com/p0093

Fuel injector failure, Fuel line common rail leak, Fuel pressure sensor malfunction
Fuel pump or lift pump failure, Fuel heater constantly on Fuel temperature sensor failure ,

Leaks at any point in the high pressure circuit Electrical connector corrosion or seating problems
Fuel pressure regulator malfunction Fuel filter plugged dropping the fuel line volume Injector pump leak
Fuel control actuator failure
Cascade overflow valve malfunction Short in the electrical harness at the injectors or to the ECM Fuel pressure limiting valve ECM failure
Copyright OBD-Codes.com

Jun 07, 2016 | Toyota Cars & Trucks

1 Answer

1989 volvo gl is not getting fuel to injectures what to do?


check the pressure and flow , if the pressure in the fuel rail is ok the injectors must have fuel to them as they are connected to the rail, may be there is no pulse to the injectors they get a pulse from the computer . if there is no pulse check the fuses.

Oct 02, 2014 | Cars & Trucks

1 Answer

Not having enough pressure from the common rail to open up injectors, also injectors not firing what could be the problem? on the other hand can injectors for 2kd work on 1kd?


sounds like fuel pump , wether it be mechanical or electric.sounds like you are having pressure problem , am not sure about swapping injectors.

Nov 14, 2013 | Cars & Trucks

1 Answer

Won't start,has spark, has fuel


Are you sure the injectors are spraying if the pressure is zero ?
Have you checked the fuel pressure regulator ?
Are the spark plugs dry ?

Dec 12, 2012 | 1998 Cadillac DeVille

2 Answers

My 2001 Saturn, will start but not stay running. We have checked the fuel pump and all fluids. Did a compression check this morning, fuel injectors are not injecting fuel into fuel rail. Why is engine...


You said, 'fuel injectors are not injecting fuel into fuel rail' but it's my understanding that the fuel rail gasoline is supplied by the pump, and the fuel injectors just pulse to allow fuel to get to the cylinders. I would check out the fuel delivery problem further. Check for pressure in the fuel rail that is within specs.

If not, then the pump or fuel pressure regulator may be the problem. Check the fuse for the fuel pump. If good, then the pump may be bad in the tank.

Good luck on this.

Feb 05, 2011 | 2001 Saturn L-Series

1 Answer

Will not start, ether in the injectors turns it over


CHECK FUEL PRESSURE AND INJECTOR PULSE, IF YOU HAVE A NOID LIGHT. THERE IS A FUEL PRESS TEST PORT ON THE FUEL RAIL. KEY ON ENG OFF PRESS 35-45 PSI IF ITS A V 8 ENG 50-60 IF ITS A STRAIGHT 6. TO CHECK INJECTOR PULSE DISCONNECT THE EASIEST INJECTOR AND PUT THE NOID LIGHT IN THE CONNECTOR AND TURN THE ENG. OVER IF IT FLASHES YOU HAVE INJ PULSE. START THERE AND SEE WHAT YOU GET.

Aug 04, 2009 | 1992 Ford F150 SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...