Question about 2002 Buick LeSabre

Open Question

Where is the wheel speed sensor on 2000 buick lasabre

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 19 Answers

SOURCE: 1997 buick lasabre custom high idle, transmission, stalling

had same problem i would check the Idel Air Valve and also check all of your vaccum hose lines makeing sure there are no cracks or splits in rubber connectors if there is repair immediatelt because over time they start to dammage the internal parts fo the engine and if youve replace tps mass air etc. sounds like a vaccum hose problem

Posted on Feb 10, 2009

  • 1201 Answers

SOURCE: KNOCK SENSOR

When a knock is detected, it sends this information to the computor, in which retards the ignition timing. If the sensor is bad, it will do this more often than not.

Posted on Mar 30, 2009

  • 1986 Answers

SOURCE: how do i remove the rear passanger 2000buick lasabre door panel.

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 31 Answers

SOURCE: DASHBOARD PROBLEM WITH GAUGES NOT WORKING. 2000 BUICK LASABRE

your gauges need to be replaced it sounds like you have a bad mother board on it.

Posted on Jan 30, 2010

  • 262 Answers

SOURCE: 94 Buick LaSabre Hesitation

Clean the sensor wire in the mass air flow sensor. Remove the tamper proof screws to remove the sensor holder and clean off the wire with carb spray or brake cleaner. Do not touch the wire with hands or rags.

Posted on Feb 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing a fuel sensor on a 2000 Buick Lasabre


On the LaSabres they have a fuel tank pressure sensor and a fuel level sensor if either one has to be replaced they are built in to the fuel pump.You can get to the fuel pump by removing the rear seat and removing the panel to remove the pump.The fuel pump is located in the tank.

Jan 27, 2011 | 2000 Buick LeSabre

1 Answer

94 Buick LaSabre Hesitation


Clean the sensor wire in the mass air flow sensor. Remove the tamper proof screws to remove the sensor holder and clean off the wire with carb spray or brake cleaner. Do not touch the wire with hands or rags.

Feb 24, 2010 | 1994 Buick LeSabre

1 Answer

DASHBOARD PROBLEM WITH GAUGES NOT WORKING. 2000 BUICK LASABRE


your gauges need to be replaced it sounds like you have a bad mother board on it.

Jan 30, 2010 | 2000 Buick LeSabre

1 Answer

Why does my 2000 model buick lasabre have a bad viberation when the car is at a certain speed and the the motor is in a strain?


If vibration appears to happen just as you get to a steady cruising speed on highway, it sounds like a problem with your torque converter and/or lock up circuit. A good transmission place, or dealer should be able to diagnose properly and advise you of fix.

Jan 10, 2010 | 2000 Buick LeSabre

1 Answer

TRACTION LIGHT STAYS ON AND ABS LIGHT AFTER STARTING CAR 97 buick lasabre


There is a good chance that the wheel speed sensor, (ABS sensor) has gone bad or gotten to dirty. It's common for the ABS sensor to get too dirty and can not read the speed ring on the wheel hub since it's magnetic. The common repair is to spray Brake Parts Cleaner on the ABS and speed ring on the hub and inspect for damages to the wire harness. The ABS sensor is on the inside of the wheel hub so it's easy to get to, if you not sure what your looking for. Remove the wheel and along the A-arm, you will find a wire harness which leads to the wheel hub (Bearing). There is where your going to find the sensor, just clean it and inspect for corrosion and gap, you can take paper and fold it 5 times and place it between the sensor and speed ring for the proper gap. Good luck and keep me posted, if there is a Auto Zone around your area, have them scan the car just to make sure it's not your ABS modulator which would cast $$$ to replace.

Nov 02, 2009 | 1997 Buick LeSabre

1 Answer

Kidspeedy hopefully buick lasabre that runs rough


I also had a misfire, but on a 4cyl. At speed it was great-getting there? so yes do the tune up of plugs and wires. You only have one cyl out of six laying down on you, might not even be hardly noticable.

Aug 26, 2009 | 2000 Buick LeSabre

1 Answer

Oil sending unit on buick lasabre 2000 is leaking .


Passenger side wheel well. Screwed in the block above the passenger side cv shaft below the power steering pump.

Aug 22, 2009 | 2000 Buick LeSabre

2 Answers

Shutting Down


hsve the crankshaft sensor checked

Sep 04, 2008 | 2000 Buick LeSabre

Not finding what you are looking for?
2002 Buick LeSabre Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...