Question about Hyundai Sonata

Open Question

Coil pack arching

Arching coil packs to valve cover

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 625 Answers

SOURCE: 2000 jetta vr6 coil pack

i need the engine size in order to answer your question, since this car come with, 1.8 1.9 2.0 and 2.8 engines on it please tell me wich one you have and we go from there

Posted on Jun 17, 2008

  • 73 Answers

SOURCE: 1994 pontiac transport se not firing in first coil pack at idle

ARE YOU CHEKING SPARK OFF THE COIL TOWER OR AT THE SPARK PLUG END OF THE WIRE SOUNDS LIKE YO HAVE A BAD WIRE

Posted on Apr 24, 2009

  • 14036 Answers

SOURCE: 2000 Kia Sephia p0303 code engine misfires

do a compression test. cylinder 3 could have a bad valve lifter or valve.kia sephia dont have push rods.it have a bucket type followers.a intake leak to that cylinder can also cause misfire problems.

Posted on Jun 06, 2009

  • 11 Answers

SOURCE: not getting spark

Testing the coil packs.

1. Get an INSULATED wire and hook it to a ground on the car.
2. Get some one to help you
3. pull a spark plug wire off the coil
4. hold grounded wire close to, but not touching, the part where the spark plug wire connects
5. keep hands away from coil and have your helper turn the engine over ( start car and turn off)
6. if there was a spark between the wire and the coil pack it is good. if not, the coil pack needs replaced
7. replace the spark plug wire
8. test the rest

Posted on Jul 03, 2009

emissionwiz
  • 75005 Answers

SOURCE: how do you remove the

You must remove the upper intake manifold, the upper intake is what the flexible air hose from the air cleaner connects to on the engine, the plastic trim covers over the the upper intake just snap off and on, it is a ball socket snap, carefully pull up at the corners of the plastic engine trim covers, and the bare aluminum upper intake is under that, there is no coil pack, each cylinder has its individual own coil over the spark plug, suggest you replace the plugs while all this is apart.

Posted on Jun 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil on coil packs and within the spark plug. When taking out the coil pack I can see oil coming from top going down into the spark plug chamber


if the coil goes into the valve covers i would install new value cover gaskets and that should take care of the oil getting on the coil packs or the coil packs are leaking and then you should change them.i looked up your vehicle and noted that the coils are separate from the valve covers,i would inspect the coils and the valve covers and replace as needed, if you find that the coils are leaking you should change it so that you don't have an ignition problem later, autozone has them for your car around 52each or 250-300a set with lifetime warranty

Nov 16, 2016 | Cars & Trucks

1 Answer

How do I find the coil pack on my 2004 kia optima?


The coil pack is located under plastic cover in upper motor y valve cover. this vehicle have a 2 coils, one for 2 cilinder

Jun 29, 2014 | 2004 Kia Optima

1 Answer

I would like to know how to change the spark plugs on the 1999 Isuzu Rodeo 3.2 liter


unplug the connectors for the ignition coil packs, then unbolt coil packs, remove coil packs (all 6 are interchangable) then remove and replace spark plugs. There is a row of three coil packs behind the oil fill cap on the valve cover and three on the other side.

Apr 25, 2012 | Isuzu Rodeo Cars & Trucks

1 Answer

How do I change sparkplugs?


YOU HAVE TO REMOVE COIL PACK WITH PLUG BOOTS ATTACH TO COIL ASSEMBLY FROM TOP OF VALVE COVER.YOU HAVE 4 SCREWS ON CENTER TOP VALVE HOLDING COIL PLUG BOOTS ASSEMBLY IN PLACE. ONCE YOU REMOVE COIL PACK ASSEMBLY WITH PLUG BOOTS.THE SPARK PLUGS UNDER THE COIL ASSEMBLY.YOU CAN REMOVE SPARK PLUGS.FROM TOP VALVE COVER WHERE YOUR COIL PACK COME OUT.YOU NEED DEEP 6" INCH SPARK PLUG SOCKET AND EXTENSION TO LOOSEN AND REMOVE SPARK PLUGS. YOU NEED SPARK PLUG GAP GAUGE.YOU NEED TORQUE WRENCH.NOT MANDATORY LONG AS YOU DONT OVER TIGHTEN SPARK PLUGS.STRIP THREADS.IN HEADS

Feb 18, 2011 | 2003 Saturn ION

1 Answer

How do you get to the spark plugs 2005 hyundia santa fe


There's a plastic cover on the valve cover, remove small bolt's holding cover, under cover will be two coil pack, and a total of 4 spark plug wire's, remove small bolts to coil pack, will have two bolts to each coil pack, disconnect elec. harness, remove coil pack, spark plugs will be in there.

Sep 20, 2010 | 2005 Hyundai Santa Fe

1 Answer

Where is the coil pack located on lincoln ls v8 7


Driver side valve cover
7mm socket to remove coil covers and coil

1 thru 4 pass side
5 thru 8 drivers side
Front to back

Jul 12, 2010 | 2002 Lincoln LS

1 Answer

How do i put in spark plugs in my 2005 dodge ram 1500


I'm assuming this is a 5.7 hemi. Remove the 8 coil packs that are bolted to the top of the valve cover. You can do 1 at a time. Each coil pack has two spark plugs under it . use a 5/8 spark plug socket and extention. If its a 4.7 the coil packs are held on by one 10mm nut. These packs are just inside the valve cover on both sides of the engine. There will be only one 5/8 plug for each pack

Jun 25, 2010 | 2005 Dodge Ram 1500

1 Answer

Dont know how to take master cylinder off to replace coil pack


You shouldn't have to remove it....here are the steps from the tech manual:

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Label and disconnect the spark plug wires from each of the coil pack towers.
3db79bc.gif
Ignition coil removal—2.4L engine

2f61688.gif
Ignition coil removal—3.3L and 3.8L engines


  1. Disengage the electrical connector from the ignition coil pack.
  2. Remove the coil pack mounting fasteners.
  3. Remove the coil pack from the vehicle. If equipped, remove the coil pack from the mounting bracket.
To install:
  1. Place the coil pack into position on top of the engine valve cover, or mounting bracket, if equipped.
  2. Install and tighten the coil pack mounting fasteners to 9 ft. lbs. (12 Nm).
  3. Plug in the electrical connector to the ignition coil pack.
  4. Connect each spark plug wire to each corresponding coil pack tower. The coil pack towers are numbered with the correct cylinder identification. Be sure that the spark plug wires snap firmly onto each coil tower.
  5. Connect the negative battery cable.

Jan 18, 2010 | 2001 Chrysler Voyager

1 Answer

Every now and then i smell oil burning when i use my heat but u never see it on tha ground or anywhere


Most likely an oil leak around the ignition coil packs in the valve covers. Remove the center covers on the valve covers and remove the coil packs and see if you have oil in the spark plug wells and on the coil pack boots. If so you will have to replace valve cover gaskets and the orings around the coil pack holes. You can also get the coil pack boots separately if the are oil saturated.

Mar 05, 2009 | 2002 Lincoln LS

2 Answers

2000 jeep cherokee sport 4.0


I believe that year had distributorless ignition, instead it uses a form of coil on plug ignition system.

If you open the hood, stand at the front of the vehicle. Look to the left side of the engine, around the bottom of the valve cover (The valve cover is where the oil fill cap is. The oil fill cap is on top of the valve cover), at the bottom of the valve cover on the left side you will see a series of humps. Those series of humps is the coil packs, the coil packs are all in one long piece held down by three or four bolts.

Take out those bolts, gently pry up at the ends of the coil pack and it will eventually come out. You'll see on the bottom side the spark plug boots are attached to the coil pack. After you get the ignition coil pack off, you will see the spark plugs under where the coil pack came from, the boots on the coil pack sit directly on the spark plugs.

Jan 01, 2009 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...