Question about Cars & Trucks

Open Question

What clutch is in a 04 plate ford focus 1.8 tddi, a dual mass flywheel or steel ?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 150 Answers

SOURCE: rear humming noise on my ford focus suspect rear wheel bearings

If the humming is more pronounced when you turn corners it is one of the wheel bearings.Listen to determine which side. They can be done easily DIY but only with some mechanical knowledge.The old bearing casings need to be removed from the hub using a small chisel or drift. The new ones need to be pressed back into the hub ideally but can be done using a hammer and a suitale sized socket.

Posted on Mar 21, 2009

  • 8 Answers

SOURCE: ford focus 1.8 tdci MY 2003 terrible cold start

Possibly is your glow plugs, best to change then all yourself if you can with just a ring spanner and a deep seated socket. Also not enough power in battery to heat plugs up in first place can be the cause. When deisels have been started a few mins, usualy start without waiting for glow plug to go out.

Posted on Apr 05, 2010

  • 122 Answers

SOURCE: 04 ford focus 1.8 tddi changed fuel filter turned

perhaps isnt in the right flow direction check the arrow mark on the filter to match with the flow of the gas.if is ok try to remove the air from the pipes.

Posted on May 28, 2010

  • 2187 Answers

SOURCE: I replaced the clutch assy. in a 2003 santa fe 2wd

Check if there is air in the system. You need to bleed out the clutch. Inspect the pedal linkages for binding or anything out of the ordinary. If bleeding the clutch did not resolve the issue, you need to go back to the transmission and inspect the fork or pivot ball. It could be possible that the conversion kit did not match the model that you have. It is possible that bad seals causing debris may have caused the issue and it was just coincidence that after replacing the flywheel did this happen.

You may also need to replace transmission fluid.

Posted on May 12, 2011

jgwhomeequip
  • 1902 Answers

SOURCE: Renault traffic 6 speed 53

Sounds like the throwout bearing is going bad. Which is telling you that it might be time for a new clutch kit in your vehicle

Posted on Jun 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have just got a Ford Focus 18 tddi 04 plate and the EML is on! any ideas or advice


You need to take the car in and have the engine control module scanned for the fault code that was set in memory when the check engine light (you foreigners call it an engine management light) came on. It can be any of hundreds of problems.

Feb 28, 2017 | Ford Cars & Trucks

1 Answer

Ford problems


http://www.ebay.com/itm/BRAND-NEW-SOLID-FLYWHEEL-GENUINE-FORD-CLUTCH-CSC-FORD-MONDEO-2000-2007-2-2-D-/321233915244?pt=Motors_Car_Truck_Parts_Accessories&hash=item4acb088d6c&vxp=mtr

Jan 02, 2014 | Cars & Trucks

1 Answer

Ive got ford mondeo tdci 54 plate.. ive just had the dual mass flywheel replaced but now the clutch is playing up it goes stiff and wont go into gear, could this be it needs clutch fluid??


Angela, I'll be honest I'm confused. It shows "problem with Toytoa Celica" but you mention a Ford Mondeo in your post. Just to be sure we're talking about a Ford Mondeo that had the flywheel replaced, correct? Chances are if they replaced the flywheel you normally would always replace the clutch disk with it. If this is a hydraulic clutch system you don't typically have to open the hydraulic system to swap out the flywheel and clutch on a car. This would lead me to believe clutch fluid isn't your answer, but I would at least make sure you check it. If they DID have to open the system the clutch needs to have the air bled out of the hydraulic lines.

Nov 24, 2012 | 2002 Toyota Celica

1 Answer

Grinding in tranny after replacing clutch


Did you remember to torque all of your clutch plate bolts? Flywheel bolts?

May 04, 2010 | 1996 Ford F250 Crew Cab

1 Answer

Starter motor is jamming


NO,when the dual mass flywheel goes you will feel it.starter motor jamming is normally down to worn teeth/release spring.

Apr 26, 2010 | 2001 Ford Focus

2 Answers

Dual mass fly wheel


did u git the timin rite-now the flywheel fits as replacement correct-do u hav a repair manual!

Aug 16, 2009 | Ford Focus Cars & Trucks

1 Answer

Does not rev up when taking up a small incline,heavy noise coming from clutch. Have replaced cluth and pressure plate for the second time.The selection of gears are very hard , does not select well. Iwould...


There is a company in Northern Ireland called Exact Engineering that can convert your dual mass flywheel to single mass using a complex engineering process ending with a finely balanced guaranteed single mass product. They have a complete courir service.

You can see their website at www.exact-spec.com and contact them at info@exact-spec.com

May 03, 2009 | 2003 Jeep Liberty

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...