Question about 1999 Jeep Grand Cherokee

1 Answer

Diconneted battery to clean cables now abs and brake light is on

Posted by on

  • DanyielAI May 11, 2010

    Probably needs a reset. Might reset after you drive it for awhile. Otherwise the dealer will need to do it or a shop. Hope this helped.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 50 Answers

Disconect positive cable on battery weit one min and conected back on will reset ewrting make shore ignation kay off position wen yu disconect batt

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Multiple lights on the ipc, signals inoperative, interior lights inop, and signals at time


check battery volts see if battery volts are 12.6 volts.battery could be weak or battery cables and battery post terminals need cleaning.

Feb 06, 2013 | 2000 Ford Windstar

1 Answer

Driving home today in our 2004 Jetta. first the ABS lights came on, then the air bag warning, then the brake light, then the battery light, and an EPC light, all within minutes, then the power steering...


WILL THE ENGINE START? IT SOUNDS LIKE THE BATTERY IS LOW OR THE BATTERY CABLES & TERMINALS NEED TO BE CLEANED. TAKE THE NEG. CABLE OFF FIRST THEN THE POSITIVE, CLEAN EVERYTHING TERMINALS & CABLES, PUT CABLES BACK ON BATTERY POS. FIRST, TIGHTEN IT. THEN DO THE NEGATIVE & TIGHTEN IT.

Dec 25, 2010 | 2004 Volkswagen Jetta

2 Answers

ABS light always on- any way to turn it off- i am


under the hood you will find a relay center ,the relay for your abs is bad.the way it effects the braking system is (now that the abs light is on )when you slam on the brakes your truck will skid to a stop,the abs system prevents the skidding,you will feel the brake pedal pulsate until stopped.

Jun 05, 2010 | 1997 Ford Explorer AWD

2 Answers

I Have a 2002 Dodge Ram 2500.Both the ABS and Brake Lights are on


Hi!!

Did you have the ABS sensors checked ?? The brake fluid level when low also activates the Brake and ABS lights?? Drive truck to an AutoZone store and ask to have computer codes scanned. This is a free service for all customers. This will help you to pinpoint the problem.

Good Luck!!

Don't forget to rate this post.

Jun 04, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

I Have a 2002 Dodge Ram 2500.Both the ABS and Brake Lights are on


did you check the brake fluid level? you dont just go replacing parts without knowing what is bad. The abs unit will have trouble codes, get those codes and tell us what they are.

Jun 04, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

Lincoln ls 2004 service park brake light keeps coming on


This can be brake wear sensor or ABS sensor.
I can not help you on the brake job but you can verify it by listening carefully for a metal to metal contact sound.
This is a small metal tab that make noise when the pad is low. This warn you to service the brakes soon.
=========
For dirty ABS sensor
The simple DIY method is to gently hose down each wheels when there are COMPLETELY COLD. Dirt can cover to ABS sensors.

Most failure are from the front wheels because of the heat.

The car wash with under side cleaning will also do the trick if it's a dirt related problem.

Remove the negitive battery cable or clear OBD-II code.

MAC and OTC make ABS senor tester to pin point the trouble spot but it cost $$$.

Do the preventive cleaning before bring it to the shop.

Aug 23, 2009 | 2004 Lincoln LS

1 Answer

Abs light on dash is lit brakes are good


Did some research and found that the module that connects to the ABS pump (next to battery) to be the problem. ISUZU wanted $3,200.00 to fix it. Bought one off of a wreck for $146.99 (LOL, yep, $146.99). Removed battery, disconnected the large cable going to the ABS, unclipped the 3 brake line clips on the top of the fender so the ABS pump could be removed and swapped the electronic modules- did not have to penetrate the brake lines at all. Took me 20 minutes. Restarted Trooper and ABS light went out.

May 08, 2009 | 2001 Isuzu Trooper

1 Answer

Abs & Brake light on.


I have found that the wheel sensors for the abs system get very dirty and cause the abs warning light to come on. You can try to clean them if you have the tools to take them off but usually you just want to replace them.

Your brake warning light and your rear braking problem may be caused by the same problem,
the cable sticking. Good luck!

Dec 30, 2008 | 1997 Chevrolet Cavalier

2 Answers

When you brake and the van is near a complete stop the brakes let go a little then kick in hard. Sounds almost like when you start the vehicle and the ABS light goes out


As I already knew one of my rear wheel bearings was going, ie lots of noise above 60km, vehicle has 250K KMs, I read my service manual and it indicated most probable one of the bearings reading zero under 5 KM per hr causing full pressure by the ABS to be exerted on the rear brakes. Works fine with the ABS cct breaker pulled. Solid brakes with ABS above 5 km/hr. No ABS light on, do not have an ABS code reader only the basic GM code reader. Vehicle is 1992. Thanks Anyway

Jul 21, 2008 | Pontiac Trans Sport Cars & Trucks

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...