Question about 1986 Chevrolet Corvette

Open Question

Location of starter enable relay on 1986 corvette

Will not crank

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 21 Answers

SOURCE: starter relay position for 1991 RS Camaro

It is located on the left hand kick panel fairly high

Posted on May 03, 2009

  • 1 Answer

SOURCE: trying to locate fuel pump relay for 1991 corvette- coupe

The fuel pump relay in the 1991 corvette is located under the IP on the pass side.
Open pass door, unscrew two screws under the glovebox (you will be upside down in the car), take off the fuse panel, unscrew third screw to plastic plate underneath glovebox, pull away carpet (velcro), pull down plastic plate (watch out for the wiring to the lamp), then under the glovebox you will find a number of fuses and relays if you dive in under there DEEP, prob 4 or 5 in a row, not really sure wich one, but one in the middle is the fuel relay, and they are the same (interchangable).
Take a look at --the12volt.com/relays/relays.asp--
It´s those relays we are talking about.

Posted on Sep 12, 2009

wireguy212
  • 1627 Answers

SOURCE: I need the location of the sterter relay on 77

passenger side near the back of the engine.it bolts to the transmission housing.the bolts go up into the the transmision housing.

Posted on Oct 14, 2009

  • 355 Answers

SOURCE: vats system disengages fuel injection and starter

The resistor, unfortunately, will only bypass the key and the lock cylinder, but not the TDM that is the core of the VATS system. The TDM is the one often faulty instead - as it happened to me. Here is a great write-up to build yourself a full bypass that will also bypass the TDM. It is quite easy and it saved my car: http://newrockies.ca/vatsbypass

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Which relay is the starter relay for a 97 buick lesabre


the one that is labelled starter relay,btw,those are fuses

Jun 26, 2015 | Buick Cars & Trucks

1 Answer

Corvette horn not working


I have a 1999 corvette and the horn will not blow when pushing on the horn pad. It beeps when locking the car and security system.how do I locate the problem. Thanks Bob

Jul 12, 2012 | 1986 Chevrolet Corvette

1 Answer

My 1996 Buck LeSabre won't turn over. I took the starter off and had it checked, it was fine. I checked the starter fuses and all was fine. \ Cabling was fine to the starter, voltage was 12.54...


Be sure the AIR BAG/VATS fuse 10 amp, is good. there is a STARTER ENABLE RELAY up high on the left of the steering column. I ASSUME the anti theft light is not flashing?" at the STARTER ENABLE RELAY the YELLOW wire is hot in the crank mode and comes out large PURPLE to the starter. the small purple wire is hot in the crank mode if the fuse (air bag/vats) is good. the small yellow is grounded through the park switch and the VATS module (anti theft)

Sep 21, 2011 | Buick LeSabre Cars & Trucks

1 Answer

Car won't start no power at fuel pump or fuel pump fuse. Thanks Brian


Locate and replace the fuel pump relay and see if it will start then. Also, make sure that the battery terminals are clean and secure; also on the starter, and the ground (at chassi - or block, wherever the ground leads).

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

Jun 30, 2010 | 1986 Chevrolet Corvette

1 Answer

Vats system disengages fuel injection and starter in my 1986 corvette. have checked resistence on pellet and bypassed with resistor. replaced the ecm and all relays


The resistor, unfortunately, will only bypass the key and the lock cylinder, but not the TDM that is the core of the VATS system. The TDM is the one often faulty instead - as it happened to me. Here is a great write-up to build yourself a full bypass that will also bypass the TDM. It is quite easy and it saved my car: http://newrockies.ca/vatsbypass

Nov 12, 2009 | 1986 Chevrolet Corvette

1 Answer

Does an 86 corvette have a starter relay? the starter does not work all the time. i have put a new battery and made sure the starter was good.


use a 12v test light and check for voltage on small solenoid wire at the starter while turning the key to start.This will let you know which way to go .There is no relay involved that would interupt this signal to the starter from the ignition switch unless added aftermarket for an alarm system.

Jul 14, 2009 | 1986 Chevrolet Corvette

1 Answer

Transfer Case Switch Wiring Diagram


locate the fuel pump relay for a 1986 chevy corvette

Jul 23, 2008 | 1986 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...