Question about 2006 Chevrolet Colorado

Open Question

Where is the BCM located in a 2006 chevrolet colorado

Replacing the bcm in my 2006 chevy colorado where is it located

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: looking for location of bcm on 97 astro van dash

The BCM is located immediately above the heater controls inside the dash on my 2004 Astro. I know it controls the headlights and locks but not gauges. Haynes says the gauge fuse supplies it power....but I'm not going to bank on that one.

P/N 15081796 from Napa $115

Good Luck

Posted on Feb 11, 2010

Ad
  • 355 Answers

SOURCE: Replace BCM and Passlock sensor

if it stalls while driving it CANNOT be anything related to passlock. I would check the camshaft and crankshaft sensors that are typically weak in GM cars and if they fail, the PCM would shut down the engine.

Posted on May 01, 2010

  • 355 Answers

SOURCE: replaced the bcm on my car now security light

You need to bypass the entire security system. You can find a great write-up here: http://newrockies.ca

Posted on Jul 16, 2010

czaa
  • 4995 Answers

SOURCE: BCM 2002 Chevy Trailblazer.

thats a issue for a pro cause dealers dont have olschoolers with the knowledge-they just want to sell new cars--independent shops must reprogram the computer using a landline only cause a wireless connect doesnt download the complete data--send delemma to majicmech@aol.com for more advice

Posted on Jun 03, 2011

Mr BrokRench
  • 1623 Answers

SOURCE: I have a Chevy Impala

A new BCM HAS to be programmed by a shop with a Tech II programmer.

Good luck, i hope this helps.

Posted on Jun 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to disconnect a BCM in a chevy colorado 2007


Removal Procedure
Important:
• The ignition switch should be in the OFF position when connecting or disconnecting the connectors to the body control module (BCM).
• Always disconnect the black body wiring harness connector FIRST and the gray instrument panel (I/P) wiring harness connector LAST.
• Always connect the black body wiring harness connector FIRST and the gray I/P wiring harness LAST.
• Do not open the BCM housing. The module does not have any serviceable components. The module may be replaced only as an assembly.
Ensure the ignition switch is in the OFF position.
Remove the right front hinge pillar trim panel. Refer to Body Hinge Pillar Trim Panel Replacement - Right Side .
Disconnect the body wiring harness electrical connector (1) from the BCM.
Release the fastener retaining the body wiring harness electrical connector to the BCM. Remove the 2 fasteners retaining the BCM to the hinge pillar.
Remove the BCM from the hinge pillar by unlocking the integral tab.
Remove the BCM from the vehicle.
If installing a replacement BCM, program the BCM. Refer to Control Module References .

Dec 19, 2016 | Cars & Trucks

2 Answers

WHERE IS THE FUSE FOR MY POWER STEERING IN MY 2006 CHEVY HHR LOCATED?


You vehicle has two fuse's ! one in the underhood fuse box EPS/STR WHLCNTRL an it is a 60 amp . An there is one in the BCM fuse center - EPS 2amp fuse ! do you know what an where the BCM is ? The BCM - body control module !
Body Control Module (BCM) location
Under the I/P below the radio on the right side of the center console .19
EPS/STR WHL CNTRL
2A
Electronic Power Steering (EPS) Column Assembly and Inflatable Restraint Steering Wheel Module Coil

Aug 05, 2015 | 2006 Chevrolet HHR

1 Answer

Location of turn signal flasher 2006 HHR chevy where is it located


Unlike older vehicles, the flashers on the HHR are controlled by the BCM.

If your turn signals are blinking rapidly, check the bulb connections for signs of corrosion. Clean any corroded connectors & add some dielectric grease before replacing.

Feb 13, 2015 | 2006 Chevrolet HHR

1 Answer

2004 Chevrolet colorado z71 3.5 4x4. Heater/fan,turn signal,brake lights intermittently flash on and off. Suspect bcm but don't know where bcm is and if it needs to be programmed when replaced


It's located on the passenger side A pillar. Or behind the right kick panel ! The first thing to do would be check all Modules for DTC'S ! Yes the BCM need's to be programmed when replaced !
Introduction
The procedures below will program the body control module (BCM) correctly after BCM related service, or setup the sensing and diagnostic module (SDM) serial number in the BCM after the SDM has been replaced. Before you start, read these procedures carefully and completely.
Programming a new Body Control Module (BCM)
If the BCM has been replaced, perform the following steps in order:
  1. Ensure that the battery is fully charged.
  2. Connect a scan tool to the data link connector (DLC).
  3. Turn ON the ignition, with the engine and all accessories OFF.
  4. Program the BCM. Refer to Service Programming System (SPS) in Programming.
  5. Setup the sensing and diagnostic module (SDM) serial number in the BCM. Select Setup SDM Serial Number in BCM with the scan tool.
  6. Perform the Programming Theft Deterrent System Components in Theft Deterrent.
  7. Program the key fobs. Refer to Transmitter Programming in Keyless Entry.
  8. Clear all diagnostic trouble codes (DTCs) with the scan tool.
After the procedure is completed, the personalization settings of the BCM are set to a default setting. Inform the customer that the personalization must be set again. Refer to Vehicle Personalization in Personalization.

Feb 02, 2015 | Chevrolet Cars & Trucks

1 Answer

How do you reprogram your BCM on a 2006 Chevrolet Colorado


there is a conflict in the ECM which has the immobilizer in it may be resetting with a scan tool will help or talk with an auto electrician

Oct 28, 2017 | 2006 Chevrolet Colorado

2 Answers

How do you reprogram your BCM on a 2006 Chevrolet Colorado


Sounds like the BCM is either defective or needs reprogramming. Since you are combining 3 trucks, were all working well before they became parts vehicles? In a collision, the electric wiring to the BCM may have been smashed and with "crossed" wires may have been erased or shorted.

You would swap BCM's and use the driveable one to get to the Dealer for reprogramming or Autozone, Advace, or Oreilys for a free scan.

Sep 09, 2012 | 2006 Chevrolet Colorado

1 Answer

I am trying to find the location of the fuses for the brake lights on a 2006 Chevy Cobalt sedan


{: ) The stop lamp switch controls the on/off function of the stop lamps including the center high-mounted stop lamp( CHMSL). The stop lamp switch get its power from the Body Control Module (BCM). This power is also fused but is internal to the BCM. You need to check carefully the voltages at the stop lamp switch and its on/off function. If voltage is not present at the stoplamp switch, you can check the C4 connector(light gray in color) at the BCM if there is some loose connection. Otherwise the BCM may not be giving an output voltage and will need to be repaired/replaced. I hope the problem is not caused by the BCM.

Aug 01, 2011 | 2006 Chevrolet Cobalt

1 Answer

... Replaced battery in a 2005 Chevy Colorado Crew


something puts bcm into safe mode. take neg. battery cable off and touch it to pos. post for 30 sec. leave unconnected for 6 hrs then reconnect. should work after that. just did mine. dealer wanted 400$ to change door switch

Feb 16, 2011 | 2005 Chevrolet Colorado

1 Answer

2005 chevy colorado battery went dead and when i rechanged it the drivers door window would not go up or down the other 3 did. the electric locks do not work and the horn goes off if i try to open with...


something puts bcm into safe mode. take neg. battery cable off and touch it to pos. post for 30 sec. leave unconnected for 6 hrs then reconnect. should work after that. just did mine. dealer wanted 400$ to change door switch. doing this lets the bcm reset itself

Feb 09, 2011 | 2005 Chevrolet Colorado

1 Answer

2006 chevy cobalt - door won't open


Start with the basics. Check the fuses (all of them) with a test light and be sure you have power to each and that they are good. Then be sure that the power lock relay is good by swapping it with another relay in the fuse block. If the fuses are good and the relay is swapped and the locks still aren't functioning, you may have an issue with the BCM. The BCM can be programmed to change the behavior, but if the car has had water damage, or other stress to the BCM (voltage, heat, etc.), it can sometimes damage the BCM and you will need to replace it and reprogram it at a GM dealership.

Jul 25, 2009 | Chevrolet Astro Cars & Trucks

Not finding what you are looking for?
2006 Chevrolet Colorado Logo

Related Topics:

813 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...