Question about 2008 Chevrolet Cobalt LT1

Open Question

How do i remove the front bottom seat cushion from a 2008 cobalt 2 door

I need to replace the bottom cushion from the front drivers seat

Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: I need to remove the front headrest of a 2008 chevy cobalt lt

Push the button and pull up on it at the same time

Posted on May 25, 2009

  • 206 Answers

SOURCE: Drivers seat will not go up or down

I think you will have less problems with removing the entire seat, just be careful with the wires, unhook wire harness first.

Not sure how heavy this seat is, and make sure you properly torgue everything down when you re-install for safety in a collision.

Posted on Aug 20, 2009

  • 6468 Answers

SOURCE: remove cushion on drivers side seat 2004 malibu

the seat back has a strip along the bottom edge that over laps and holds it the bottom has clips around the outside edge

Posted on Aug 17, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you remove the back seat to get to the fuel pump?

On what? 3 possible ways the rear seat cushion is removed. On some the seat has clips that lift straight up. Or some have 2 small bolts at front bottom of rear cushion. Remove the bolts and seat slides out easily. The final way is old style: a heavy wire on bottom of cushion, one on each side, fits into slots that come up from the frame underneath. To remove, push cushion hard to the rear until the heavy wires can be removed (lifted up) from the slots. Do one side at a time. These are the most difficult to remove the rear bottom cushion. You have to push hard against the cushion near the bottom of it, pushing it backwards, so the wire comes out of the slot, and then cushion can be removed.

First try lifting straight up on the cushion. Since there is an access panel to the gas tank, it is very possible the cushion is easily removed by lifting straight up.

Jun 05, 2015 | Seat Cars & Trucks

1 Answer

I am doing an extensive cleaning of my car, how do i remove back seat?

At least 3 ways the bottom cushions are held in place: some have bolts at the bottom of the cushion, one on each side-when bolts are removed, bottom cushion pulls out. Some have plastic clips on the bottom of the cushion, pressed straight down and into holes in the frame. To remove pull up on the bottom cushion. The other way of holding is a metal bar or rod (about 2 inches long) that is on the bottom of the cushion, close to the front of cushion. This bar fits into a metal clip that juts up from the frame. To remove this kind, you have to push hard on the front of the cushion, so the bar or rod lifts out of the clip. The rod only has to move backward about an inch and it will lift out of the clip. There are only two clips- each is about 1 foot from the ends of the cushion. These types of holds are the most difficult to get to move. Sometimes you need to put your knee against the bottom cushion and give it a hard shove backward. You will know when you have one side loose. That side can then be lifted up a bit. Then do the other side.

First check for 2 bolts at the bottom of the back seat cushion. When you have the bottom seat out, you can remove the top cushion (the backrest) out if you want to. The backrest usually has two bolts at the bottom. Remove them, and lift up the backrest and out. If no bolts at the bottom, just grab the cushion and lift up and then away.

Jan 19, 2014 | Mercury Cars & Trucks

1 Answer

I need to remove the bottom cushion of the backseat


Oct 11, 2012 | 2008 Buick Lucerne

1 Answer

How do i remove the rear seat in a 2008 impala

Locate the t-handles on the left and right side of the rear seat cushion.They should be on the bottom front of the seat.Press down on the seat and pull the handles to release the retainers and pull the seat up and out to remove the seat cushion.Hope this helps.Good luck.

Feb 26, 2011 | 2008 Chevrolet Impala

1 Answer

Seat warmers on drivers side have gone out. How do you fix or replace?

depending on if it is the seat bottom or the seat back as they are seperate systems if both dont work then you probably have a electrical problem with the module or the switch not the heaters them selves, if it is one of the heaters then you must remove the seat cushion and replace it or the seat back cushion the heaters are intergrated into the foam the seat cushion unbolts with two fifteen millimeter nuts just under the front of the seat and unclips from the rear as you pull up and forward the seat back cushion is much more involved and should be done by a pro

Dec 18, 2010 | 2004 GMC Sierra

1 Answer

Remove rear seat

Bottom seat cushion, push in hard on bottom (about 12 inches in from door) and pull up On the back cushion remove two b0lts on bottom of rear cushion. Open trunk, all the way forward you will see on each side 2 10 mm nuts remove those nuts then the rear cushion will come out.

Sep 08, 2010 | 1995 Cadillac DeVille

1 Answer

How do you remove the rear seat of 2004 honda accord

Release the two latches at the front of the seat cushion (pull back on the latches to release the front of the cushion).

Remove the seat cushion bolt and remove the cushion (it’s roughly in the center. You have to insert a socket extension between the back and bottom seat cushions to take it out, after you find it by pressuring the bottom cushion and looking back in there).

Remove the bolts (each side) securing the seat side bolsters (they are easy to see once the bottom cushion is removed), then remove the side bolters (gently release the clips that hold them in).

Pull the seat forward, then remove the fasteners securing the seat hinge (seat pivot bracket) and remove the seat backs.

Hope this helps you.

Dec 10, 2009 | 2004 Honda Accord

1 Answer

I need to remove the front headrest of a 2008 chevy cobalt lt

Push the button and pull up on it at the same time

Apr 04, 2009 | 2008 Chevrolet Cobalt

1 Answer

Location of a 2002 kia optima fuel filter, or maybe the fuel filter diagram

Hi on this car the fuel filter is in the fuel pump so the pump as a whole will be replaced. To get to it you will have to remove the rear seat bottom cushion. There are 2 12m bolts inbetween the top cushion and the bottom. remove them and then on the front of the bottom cushion there will be 2 plastic clips pull up on them and the cushion will pop up and you will see the acc panel for the pump.

Mar 27, 2009 | 2002 Kia Optima

1 Answer

Replace rear seat belt in 1993 Toyota Corolla

OK. On the front edge of the seat bottom cushion, pull up hard, both sides. This will dislodge the 2 clamps that holds the seat cushion to the floor. Pull the seat cushion out & set it aside. You will now see the female latches bolted to the area where the rear of the seat cushion meets the rear seat back bottom. Remove the bolts (14 mm I think).

Oct 07, 2008 | 1993 Toyota Corolla

Not finding what you are looking for?
2008 Chevrolet Cobalt LT1 Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides