Question about 2008 Saturn Outlook XE

Open Question

How to remove front windshield wiper arm on 2007 saturn outlook?

I have removed the nut to the wiper but it is not coming off. is there something else i must do? all i see is what looks to be a washer inside but nothing to keep in from coming off.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
lancer721
  • 229 Answers

SOURCE: Hi, We have a 2004

The wiper "motor" is usually located at the bottom of the fluid reservoir. Remove the fluid bottle under the hood and at the lower end of it you will find the motor. Once in a while it is located on the wall of the car under the hood - follow your fluid tubes to find and replace.

Posted on Jan 07, 2009

Ad
emissionwiz
  • 76109 Answers

SOURCE: Can't remove windsheild wiper arm on a 2003 Saturn

I use a trim removal tool to pry it up, it is a press fit.

Posted on Mar 25, 2009

  • 1915 Answers

SOURCE: Removing the rear rotors on

Unless your parking brake is on, they should just slide off-but you sometimes have to 'persuade' it using a hammer and hitting the rotor edge on the inside, rotating it so you tap it off-you do not have to get crazy, but smacking it with a hammer (put a towel over it to avoid scarring it if you feel better) will get it off-a necesary tool in any toolbox is a 4 lb. hammer, comes in handy for just such a problem.

Posted on Jul 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear wiper assembly from the rear wiper motor


flip the nut cover back up the arm and undo the nut shown
the arm base is normally on a splined taper so you may need a flat blade under the arm base on a piece of something so as not to damage the paint and lever it off the spline

Sep 02, 2015 | 2007 Saturn Outlook

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

How to take off the Windshield Wipers Arm on a Saturn Ion


At the end of the wiper arm where it attaches there will be a plastic cap over a nut.Remove the plastic cap and remove the nut and you will be able to remove the wiper arm.I hope this helped.

Feb 05, 2010 | 2004 Saturn ION

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

Front windshield wipers are crashing into each other


Yes you can adjust them yourself. First you need to check that the wiper arms are not bent. If not, remove the cap at the wiper arm base, under it u will find a nut, remove this nut. you should now be able to remove the wiper arm. (it is comon for caravan wiper arms to be corroded on. If the arm dosen't come off, you may need to heat up the wiper arm with a propane torch. be careful not to melt the plastic cowel under the arm. OR you can use a wiper puller or a battery puller. do not force it, you can break the arm, DO NOT PRY AGAINST THE COWEL OR WINDSHIELD.
Once both arms are off, turn your van on and turn the wipers on. watch the wiper posts, turn the wipers off and watch the wiper posts return and stop in the "parked" position. Turn the van off. Install the passanger wiper arm first, it is positioned closest to the bottom an inch or two above the black cowel. It should be parrallel to the cowel. next install the drivers side wiper arm. it is positioned about 4 inches above the passanger wiper. again running parrallel to the cowel and passanger wiper. tighten the lock nuts down (do not over tighten) wet down your windshield with glass cleaner or windshield washer fluid and test wipers. If they still hit you can lower the passanger one a little or raise the drivers one a little (careful you don't raise the drivers one too much or it will 'jump' off the windshield at the top of the wipe).
good luck, hope this helps.

Nov 23, 2009 | 2001 Chrysler Town & Country

4 Answers

2000 Saturn LS, windshield wipers park in the middle of the windshield. How can I fix this?


The wipers are parking in the middle because the timing mechanism is off. Once they start doing this it seems to continue to happen so the 1st suggestion is to replace the wiper motor. If U don't want to spend the $ right now it's a pretty easy fix to reset the timing. Park the wipers & remove the wiper arms. Then remove the plastic cowling that covers the wiper motor & the motor assembly. Turn the wiper assembly over without turning the motor. Remove the nut on the arm of the motor. Repostion the arm pointing away from the closet wiper directly inline with the short arm. reassemble.

Oct 24, 2009 | 2000 Saturn Ls 4dr Sedan

1 Answer

Where is the windshield wiper motor on a 2007 Dodge Caravan and how do I replace it?


Wiper Motor: Service and Repair
Removal
REMOVAL
The front wiper motor comes as a unit with a wiper pivot on each end and mounts to a shaft that holds these two inner pivots.
1. Disconnect and isolate the battery negative cable.
2. Remove the wiper arms.
3. Disconnect the washer hose at the in-line connector located near the air cleaner housing.
4. Lift the cowl grille and disconnect the washer hose grommet from the hole in the wiper module. Pull the washer hose and the grommet
completely through the wiper module tub hole.
5. Remove the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
6. Remove the four brace nuts holding the wiper tub to the lower windshield fence.
7. Remove the four bolts underneath the wiper tub inner brace holding the tub to the bulkhead.
8. Remove all four inner support brace mounting nuts and pull the inner braces just free of the mounting studs.
NOTE: The wiper tub will drop down slightly.
9. Disconnect the driver and passenger side wiper link ends at the inner pivots.
10. Remove the two left wiper motor assembly mounting nuts.
11. Remove the two right wiper motor assembly mounting nuts.
12. Partially lift out the wiper motor assembly out of the wiper tub.
13. Disconnect the wiper motor electrical connector.
14. Remove the wiper motor assembly the rest of the way from the wiper tub and remove from vehicle.
--------------------------------------------------------------------------------------------
Wiper Motor: Service and Repair
Installation
INSTALLATION
1. Install front wiper motor assembly onto wiper tub.
2. Connect the electrical connector to the front wiper motor assembly.
3. Install the four mounting nuts. Tighten nuts to 9 Nm (80 in.lbs.).
4. Push the four inner support braces onto the studs and install the four nuts. Tighten the nuts to 9 Nm (80 in.lbs.).
5. Install the four bolts underneath the wiper tub inner braces that hold the wiper tub to the bulkhead. Tighten the bolts to 17 Nm (150 in.lbs.).
6. Install the four nuts holding the wiper tub to the lower windshield fence line. Tighten nuts to 7 Nm (65 in.lbs.).
7. Apply grease to drive link bushings.
NOTE: Make sure to use Mopar(R) approved grease.
8. Attach the driver and passenger side outer wiper linkage to the inner pivots on the front motor assembly and firmly snap into place.
CAUTION: Do not apply too much force to engage link bushing or damage can occur to the drive link bushing.
9. Position the cowl grille in place.
10. Install the washer hose and grommet into the wiper tub.
NOTE: Be sure to properly seat the washer hose grommet into the bottom of the wiper tub.
11. Connect the washer hose at the in-line connector located by the air cleaner housing.
12. Install the cowl grille.
CAUTION: Be careful not to scratch the cowl grille on the corner of the hood.
13. Connect the battery negative cable.
14. Verify that the wiper motor is in the Park position by cycling the wipers system. When done, remove keys from ignition.
15. Install the wiper arms.
16. Align the wiper arms and tighten nuts to 35 Nm (25 ft.lbs.).
17. Install the wiper arm nut caps.

f7c141f.jpg

Sep 13, 2009 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

Wiper motor replacement


SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the windshield wiper pivot arms (17527).
    1. Remove the nuts (one each side).
    1. Remove the windshield wiper pivot arms.
  1. Remove the LH and RH cowl top vent panels.
    1. Remove the hood weatherstrip.
    1. Remove the screws.
    1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.
  1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
    1. Remove the nuts.
    1. Remove the bolt.
    1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
  1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    1. Disconnect the electrical connector.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal
  1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
  1. Remove the windshield wiper motor (17508).
    1. Remove the output shaft bolt.
    1. Remove the bolts.
    1. Remove the windshield wiper motor.

May 01, 2009 | 1999 Lincoln Town Car

2 Answers

Front Windsheild Wipers


I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield s7w~us~en~file=adobe.gif~gen~ref.gif Printable View (104 KB) Removal
  1. Remove the windshield wiper arms.
  1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
    Remove the pushpin-type retainers and the cowl panel grille.
  1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.
  1. If equipped, remove the A/C air inlet filter.
  1. Remove the 9 cowl panel bolts and position aside the cowl panel.
  1. Disconnect the windshield wiper motor electrical connector.
  1. Remove the cowl panel from the vehicle.
  1. Remove the 4 bolts and the windshield wiper motor.
    s7w~us~en~file=n0001518.gif~gen~ref.gif
Installation
  1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
    • Tighten to 15 Nm (11 lb-ft).
  1. Install the 3 windshield wiper-to-cowl panel bolts.
    • Tighten to 15 Nm (11 lb-ft).
  1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.
  1. Install the washer hose and grommet in the cowl panel.
  1. Install the 9 cowl panel bolts.
    • Tighten to 6 Nm (53 lb-in).
  1. If equipped, install the A/C air inlet filter.
  1. Position the cowl panel grille in the vehicle and connect the washer hose.
  1. Install the pushpins.
  1. Install the windshield arms and nuts.
    • Tighten to 27 Nm (20 lb-ft).
  1. Cycle and park the windshield wipers to check for correct alignment.
3c6f4d5.gif
b8a2ebf.gif

Apr 09, 2009 | 2006 Ford Freestar

2 Answers

Remove windshield wipers


nothing else holding it
with nut removed lift wiper to lock out and then just rock the base side to side and thats it off it comes

Jun 24, 2008 | 2007 Chrysler Town & Country LX New Cars

Not finding what you are looking for?
2008 Saturn Outlook XE Logo

Related Topics:

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...