Question about 1999 Ford Explorer

1 Answer

How to remove 1999 ford explorer trim panel when door is closed?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The trim is apart of the trim itself. remove them as if you would you inside door panel or trim in the car,

Posted on May 24, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: How do you remove the inner door panel on the rear

carefully pry off door handle bezel from around door handle,thenpry out the front edge of armrest control plate and disconnect.then remove the lower trim panel retaining screws there will be one also up behind where control panel was.then grab trim panel at the switch opening and pull it up and out. hope the helps you.

Posted on Jul 26, 2009

  • 1986 Answers

SOURCE: How remove the door panel?

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: Need to remove interior door panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

wfservices
  • 260 Answers

SOURCE: Door lock not working on the drivers side.

Visual Inspection Chart Mechanical Electrical

  • Binding latches
  • Door lock cylinder
  • Misaligned door
  • Lock actuator
  • Fuse
  • Relays
  • Switch
  • Wiring harness
  • Loose or corroded connections
Symptom Chart Condition Possible Sources Action
  • The door lock is inoperative
  • Circuitry.
  • Power door lock actuator (218A42).
  • GO to Pinpoint Test A .
PINPOINT TEST A: THE DOOR LOCK IS INOPERATIVE CONDITIONS DETAILS/RESULTS/ACTIONS A1 CHECK THE OPERATION OF THE SUSPECT DOOR LOCK sxn~us~en~file=box1.gif~gen~ref.gifCheck for binding or stuck conditions by manually operating the inoperative door lock.
  • Is the lock stuck or binding?
sxn~us~en~file=arrow.gif~gen~ref.gifYes REPAIR or REPLACE the binding components. TEST the system for normal operation.
sxn~us~en~file=arrow.gif~gen~ref.gifNo GO to A2 . A2 CHECK THE POWER DOOR LOCK ACTUATOR FOR LOCK OPERATION — CIRCUIT 117 (PK/BK) sxn~us~en~file=box1.gif~gen~ref.gif
sxn~us~en~file=ic0004.gif~gen~ref.gif Inoperative Power Door Lock Actuator
sxn~us~en~file=box2.gif~gen~ref.gif
sxn~us~en~file=gn0085a.gif~gen~ref.gif sxn~us~en~file=box2.gif~gen~ref.gifMeasure the voltage at the inoperative power door lock actuator connector Pin 1, Circuit 117 (PK/BK), and ground while operating the door lock switch to the LOCK position.
  • Is the voltage greater than 10 volts?
sxn~us~en~file=arrow.gif~gen~ref.gifYes GO to A3 .
sxn~us~en~file=arrow.gif~gen~ref.gifNo REPAIR Circuit 117 (PK/BK). TEST the system for normal operation. A3 CHECK THE POWER DOOR LOCK ACTUATOR FOR UNLOCK OPERATION — CIRCUIT 118 (PK/O)/163 (R/O) sxn~us~en~file=box1.gif~gen~ref.gif
sxn~us~en~file=gn0086a.gif~gen~ref.gif sxn~us~en~file=box1.gif~gen~ref.gifMeasure the voltage at the inoperative power door lock actuator connector Pin 2, Circuit 118 (PK/O) or 163 R/O, and ground while operating the door lock switch to the UNLOCK position.
  • Is the voltage greater than 10 volts?
sxn~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new power door lock actuator. TEST the system for normal operation.
sxn~us~en~file=arrow.gif~gen~ref.gifNo REPAIR Circuit 118 (PK/O) and/or 163 (R/O). TEST the system for normal operation.

Posted on Mar 11, 2010

  • 24 Answers

SOURCE: How to remove rear hatch panel on 98 Ford Explorer?

you can get a repair guide at your local auto parts store

Posted on Mar 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Removing drivers side door panel ( inside panel )


Explorer/Mountaineer and 1993-99 Ranger
See Figures 1 and 2
  1. Open the window.
  2. Unscrew the door lock knob.
  3. On Explorer/Mountaineer, remove the 2 screws retaining the trim panel located above the door handle.
  4. On Ranger, remove the two screws in the armrest and remove it.
zjlimited_442.jpg

Fig. 1: Exploded view of the front door trim panel

zjlimited_443.jpg

Fig. 2: Exploded view of the Explorer and Mountaineer 4-door rear door trim panel

  1. If equipped with manual window crank handles, pull off the handle cover, then remove the attaching screw.
  2. Remove the trim cup behind (Explorer/Mountaineer) or around (Ranger) the door handle using a small prying tool. Retention nibs will flex for ease of removal.
  1. If equipped with power accessories, use the notch at the lower end of the plate and pry the plate off. Remove the plate from the trim panel and pull the wiring harness from behind the panel. Disconnect the harness from the switches.
  2. Remove any retaining screws uncovered by the removed trim pieces.
  3. Using a flat wood spatula, insert it carefully behind the panel and slide it along to find the push-pins. When you encounter a pin, pry the pin outward. Do this until all the pins are out. NEVER PULL ON THE PANEL TO REMOVE THE PINS!
  4. Lift slightly to disengage the panel from the flange at the top of the door
  1. Disconnect the door courtesy lamp and remove the panel completely. Replace any damaged or bent attaching clips.
  2. Installation is the reverse of removal.

Hope this helps (remember to rate this answer).

Jan 10, 2011 | 1998 Ford Explorer

1 Answer

Replace door actuator


1999 Ford Explorer Door Lock Actuator
REMOVAL:
1.Remove the front door trim panel.
2.Remove the water shield.
3.Remove the power door lock actuator.
4.Disconnect the electrical connector.
5.Drill out the rivet.
6.Disconnect the actuator rod.
7.Remove the actuator.
------------------------------------
Attached images 4834d1192136560-door-panel-diagram-ford-explorer-80937917.gif

Aug 08, 2010 | 1999 Ford Explorer

1 Answer

Backdoor wont open without key battery keeps draing


Ford Explorer 1991-1999
Door Lock Cylinder
  1. Open the window.
  2. Remove the trim panel and watershield.
  3. Disconnect the actuating rod from the lock control link clip.
  4. Slide the retainer away from the lock cylinder.
  5. Remove the cylinder from the door.
  6. Use a new gasket when installing to ensure a watertight fit.
  7. Lubricate the cylinder with suitable oil recommended for this application.
e0efc39.gif

Exploded view of the Explorer/Mountaineer rear liftgate trim panel


For more details, you can visit Autozone.com (free register) and find the Repair Guide.

Good luck.

Sep 01, 2009 | 1999 Ford Explorer

1 Answer

How do you remove the inner door panel on the rear passanger door on a 2002 ford explorer


carefully pry off door handle bezel from around door handle,thenpry out the front edge of armrest control plate and disconnect.then remove the lower trim panel retaining screws there will be one also up behind where control panel was.then grab trim panel at the switch opening and pull it up and out. hope the helps you.

Jul 15, 2009 | 2002 Ford Explorer

1 Answer

Remove and replace passenger door mirror on 2009 ford explorer XLT, main part , I don't know how to remove the interior door panel. Pictures might help,


  1. Remove the front door trim panel handle bezel cover.
  1. Remove the front door trim panel handle bezel screws.
  1. Remove the front door trim panel lower screws.
NOTICE: To avoid damaging the front door trim panel, do not pull the bottom of the panel outward.
  1. Remove the front door trim panel by lifting upward on the armrest to disengage the panel clips.
  1. Disconnect the electrical connectors.
  1. Disconnect the lock rod cable from the front door trim panel.
  1. Disconnect the door handle conduit and cable from the front door trim panel.
  1. To install, reverse the removal procedure.

be patient during these procedures to not damage the trim panel...they cost $150>275 ec........GL hope this helps

Jul 06, 2009 | 2009 Ford Explorer

3 Answers

Need keyless entry code for a 04 an 99 ford explorer


On your 99 model the module is located behind the left quarter trim panel,mid-way.You maybe able to see it by removing the speaker cover or the cupholder on top. The module will have a sticker with a 5 digit code.
On the 04 the model is behind the right quarter trim panel toward the front about even with the right rear door stricker.

May 17, 2009 | 1999 Ford Explorer

1 Answer

Door panel removal


front

SECTION 501-05: Interior Trim and Ornamentation 1999 F-Super Duty 250-550 Workshop Manual
REMOVAL AND INSTALLATION Trim Panel —Front Door Removal
  1. Remove the rear view mirror mounting hole cover (17K709).
  1. If equipped, remove the window regulator handle (23342); refer to Section 501-11 .
  1. If equipped, remove the window regulator switch plate (14524); refer to Section 501-11 .
  1. If equipped, disconnect the power windows, power door lock switch and power mirror connectors.
  1. If equipped, remove the front door trim panel reflector or the courtesy lamp lens.
  1. Remove the screws.
3e120ac.gif
  1. NOTE: Remove the front door trim panel (23942) by pulling it straight upward.
    Lift and remove the front door trim panel.
  1. If equipped, twist the courtesy lamp connector one half turn and remove it from the front door trim panel.

Apr 17, 2009 | Ford F-350 Cars & Trucks

1 Answer

Side mirror of 2005 ford explorer


Exterior Mirror Removal and Installation
All vehicles
  1. NOTE: Left side exterior mirror shown, right side similar.
    Remove the interior door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the inside door handle bezel from the trim panel.
  1. Remove the window switch assembly.
  1. Disconnect the window switch and power door lock electrical connectors.
  1. Remove the upper trim panel screw at the window switch opening.
5c94a3e.gif
  1. Remove the lower trim panel screws.
2de1016.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, do not pull directly outward for this step.
    Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  1. Disconnect the power mirror electrical connector.
  1. Remove the trim panel.
  1. Remove the weather shield.
Vehicles with power, heated or approach lamp equipped exterior mirrors
  1. Disconnect the electrical connector.
All vehicles
  1. Remove the bolts.
a2275a5.gif
  1. Remove the exterior rear view mirror (17682).

Feb 23, 2009 | 2003 Ford Explorer

1 Answer

CHANGE SPEAKERS


you have to remove the door trim panel or the rear quarter panel.

Feb 16, 2009 | 1994 Ford Mustang

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
1999 Ford Explorer Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...