Question about Jeep Cherokee

1 Answer

Hazard switch on 91 jeep cherokee not staying engaged

When I push the button in, it will not stay, it pops back out but will flash hazards lights when I push it in and hold it.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 34 Answers

I would say the switch is bad

Posted on Apr 19, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 114 Answers

SOURCE: Fix for no brake lights on Dodge Ram Van

Also if you work it on and off about 50 times it cleans the contacts up and will work ok also.

Posted on Mar 21, 2009

goofduck
  • 490 Answers

SOURCE: Hazard lights will not turn off!

sounds like you will have to change the switch for the emergency flashers

Posted on Apr 13, 2009

  • 73 Answers

SOURCE: 99 jeep cherokee Blinker problem

Hi Bill,I think before replacing anything else you should give that hazard switch a good workout.The switch doesn't get get used very often and the contacts get corroded and can upset the indicators.Good Luck.

Posted on May 16, 2009

  • 1 Answer

SOURCE: hazard lights flash by themselves, doors won't stay locked (unlock by themselves) key fob won't work.

I has a similar problem and I just took the battery out of my remote. I think there is a problem/ short in the remote. It's as if the button is being pressed when it is not. I will use my spare one in the mean time. It was driving me crazy becuase I was driving long distance at the time and when I removed the battery it stopped. I hope this works for you!

Posted on Jun 19, 2009

  • 166 Answers

SOURCE: Tiburon 04, left turn signal lights stay on

replace the turn signal 'Clicker' also known as the turn signal relay. Most likely the problem unless you have a really wierd electical issue that will be hard to isolate...

Peace,

Posted on Mar 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal relay 2008 jeep location


There is no relay , controlled by integrated power module . Electronics !

Feb 12, 2016 | 2008 Jeep Grand Cherokee Laredo

1 Answer

No turn signals. hazard lights work only when button is held in. Hazzards will not stay on. Is problem in turn sig switch or hazard light switch


If hazard switch wont stay engaged and the turn signals run through it I would replace hazard switch then retest

Apr 11, 2015 | Cars & Trucks

1 Answer

Hazard lights blink when unlocking my 2002 toyota camry


if the indecators stay flashing permenant after unlocking then there is a switch that is closed circuit perminantly on or there is a loose earth more than likely a lose earth after changing the battery

Sep 02, 2012 | 2002 Toyota Camry

1 Answer

1992 Ford Ranger Turn signal/Hazard light issue


Can you just check to make sure the ignition key switch is not staying over to far and not backing off when you try to start it. I had a truck that did that and it messed up my turn signals until I brought the key switch back a little after starting it. Just a simple idea. Be kind with your rating for me. Raz

Apr 19, 2010 | 1992 Ford Ranger

1 Answer

2004 audi A6 flasher lights


You need a new hazard light switch - the relay for the hazards and turn signals is built in. It's $40 or so at a dealership to buy a new one.

May 19, 2009 | 2004 Audi A6

1 Answer

99 jeep cherokee Blinker problem


Hi Bill,I think before replacing anything else you should give that hazard switch a good workout.The switch doesn't get get used very often and the contacts get corroded and can upset the indicators.Good Luck.

May 03, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Hazard lights will not turn off!


sounds like you will have to change the switch for the emergency flashers

Apr 13, 2009 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Hazard Lights do not work....correctly.


the emergency flasher switch is at fault and most likely needs replacement. i'm not sure what it is with chrysler products but i've had two with problem flasher switches.

Robert

Please take a moment to rate this solution thanks

Feb 11, 2009 | 1998 Jeep Cherokee

1 Answer

98 jeep grand cherokee's turn signal on the dash and the lights quit working...the hazard lights are fine.


Turn Signal Light and Hazard Lights have one separated accesory. For this component review the Page 8J-1 / Fig 2 in this document: ZJ-Secc-8J-Turn-Signals-and-Hazard-Warning-Flashes

Maybe can help you. Good luck.

Nov 09, 2008 | 1993 Jeep Grand Cherokee

2 Answers

Indicator stays on


i am going to take it you are talking about the turn signal...look for a burned out bulb...that will cause this condition

Oct 30, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...