Question about 2005 Nissan Quest

1 Answer

Tcs, check engine, and SLIP lights are all on at the same time

The car cuts off when first starting, but stays on once it starts

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Change crank sensor and cancel computer memory

Posted on May 24, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pal03246
  • 726 Answers

SOURCE: TCS, SLIP and ABS lights on

Check your brake fluid first. If that is low, top it off and recheck. If its ok, than you will need one of the rear ABS sensors. You will need to plug it in and find out which side it is. That's really the only ABS issue that car has. One of the rear ABS sensors fails.

Posted on May 09, 2009

  • 321 Answers

SOURCE: TCS/SLIP & Check Engine Light Warning

TCS is Traction Control System,and all TCS's are controlled though the Anti Lock Braking (ABS) system.Here's how it works:Each wheel,or in some cases,only the drive wheels have a speed sensor mounted near the hub or axle,and sends a speed signal to the PCM (Powertrain Control Module).The PCM monitors wheel speed continuously,and if it sees a speed out of the ordinary,say for example the right rear tire is spinning and traveling at a much higher speed than the left rear,the PCM will pulse the brakes through the ABS system on the right rear to slow down the right rear so that the left and right wheel speeds match up,this is how the traction control works.So,if you have a TCS problem,the PCM will see this and set a Dignostic Trouble Code (DTC).You need to pull the DTC's out of the system with a scan tool,diagnose and repair the DTC's.It could likely be something as simple as a malfunctioning wheel speed sensor,but you won't know until the codes are pulled out,as this will point in the general direction.Good luck.

Posted on Aug 09, 2008

  • 14 Answers

SOURCE: Tcs off, slip and engine management light with no power

Sounds like the car is stuck in fail safe mode, most likely a problem with your eltronic throttle body or possibly airflow meter.

Posted on Oct 07, 2009

Testimonial: "ive already changed the throttle body and also the abs pump yesterday and its still the same! do you think its the airflow meter then?"

dsacco86
  • 1077 Answers

SOURCE: service engine soon, TCS off, SLIP

The oil change wouldn't cause this problem. Just in-case, check the engine oil level.

There are many emission sensors in the car that will make the engine light come ON. Best way to find out what's going on is to have an auto-parts store hook up a engine code reader and tell you what the code means. Most auto-part store will do this for free.

Posted on Oct 11, 2009

Testimonial: "very helpful. i have the mechanic checked the car , the sensor says it has a malfunction in P0340"

  • 237 Answers

SOURCE: Started car to come home after grocery shopping

um yes you do and traction control also.youll nned to go to a shop to see what fault codes are stored.rear wheel speed sensor is a common failure on these.

Posted on Mar 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Just replaced valve covers on Nissan Maxima 2002 due to misfire. Now it smokes and burns oil every start? What's should I do .


If is is only smoking when you first start it up. Most likely the valve guide seals, oil is leaking into the cylinders and smoking when you start it up.

Mar 20, 2016 | 2002 Nissan Maxima

1 Answer

Tcs light flashes and p0340 code


P0340 code means "Something" is wrong in the timing...
from CMP (Camshaft Position sensor) to the crankshaft bolt.

Very first thing, verify connectors are clean and shiny.
clear all codes, even hard codes.

57f2e883-ce32-4061-b04b-ae0890f2c653.gif
612c4a6c-208f-43b8-8645-8318e85f9e48.gif
9e0c3051-1208-49b3-95d5-de3ff545fd3a.gif

Nov 23, 2013 | 2005 Mazda 6

1 Answer

TCS OFF Slip


probably a wheel speed sensor has kicked the bucket, which is why the tcs light came on , have to check your ABS system to see if its functional.

Sep 11, 2012 | 2003 Nissan Altima

1 Answer

How do you reset tcs/slip light on a 1999 infinit q45


Hi there:

Pull the codes to get started. Normla process is when the slip light will flash on and then go off. TCS is your Traction Control System. It is normal for it to go off If the rear wheels are slipping. You may have worn tires or you are driving on ice or snow. Are you on a slippery surface when this happens? You can always shut the system down by pressing the TCS off button in the center console.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 17, 2012 | Infiniti Q45 Cars & Trucks

2 Answers

How do you use the traction control system. should the dashboard light be on or off


how the tcs works is when active light on dash will be on you will only feel it working tcs uses wheel speed sensors that when your tire slips and spins faster than other wheel like spinnig out on on ice snow gravel the tcs unit will use a controlled misfire that will **** or jolt giving traction and will stay engaged until spinnig stops or you let off gas basicaly it uses the engine to **** not allowing wheels to spin out to get a feel turn on tcs find a gravel or snowy road accelerate trying to make the car slip you will feel car start to **** it works well try it so you get a feel incase you trigger tcs and catches you off guard

hope this helped
plz vote comment if any more questions reply

Jan 18, 2011 | Saturn Aura Cars & Trucks

1 Answer

I own a 2002 acura tl, last yr I had the timing belt changed. Once in while I noticed from a stop as I accelerated the car did not respond, but the engine accelerated. since then it has happened more...


Sounds like the transmission is starting to slip. If you have an Acura dealer check for fault codes, you will more than likely find a malfunction code for the transmission.

Nov 17, 2010 | 2000 Acura TL

1 Answer

About a week ago, having switched on and set off, all the brake warning lights stayed on, that is the ABS, TCS, TCS OFF and Brake System Warning lights. The brakes continued to work OK with no extra travel...


abs=anti-lock brake system/ tcs=traction control system ==sounds like you have a problem with ur abs possible bad sensor or a wiring connection problem when abs shuts down [trouble light] your brakes will work normal but if u stomp or brake hard the brakes will lock up skid and the tcs doesnt affect brakes but if u accelerate hard tires will spin lose traction check the wiring and connections to the sensors sometimes debris hits the wire and loosens the connection if looks ok and light is on have car scanned for the trouble code most auto stores such as auto zone/advanced auto offer this service for free the code will what and where the problem is so repair can be made

Jul 18, 2010 | 2000 Mazda 626

2 Answers

Service engine soon, TCS off, SLIP


The oil change wouldn't cause this problem. Just in-case, check the engine oil level.

There are many emission sensors in the car that will make the engine light come ON. Best way to find out what's going on is to have an auto-parts store hook up a engine code reader and tell you what the code means. Most auto-part store will do this for free.

Oct 11, 2009 | 2004 Nissan Quest

1 Answer

Tcs off, slip and engine management light with no power


Sounds like the car is stuck in fail safe mode, most likely a problem with your eltronic throttle body or possibly airflow meter.

Oct 02, 2009 | 2003 Nissan 350Z

Not finding what you are looking for?
2005 Nissan Quest Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...