Question about 2006 Toyota Camry

Open Question

Toyota 2AZ engion timeing chain mark

Timeing mark of chain and balancer shaft

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75817 Answers

SOURCE: timing balance shafts on 2az fe toyota

Take a look at the engine below with chain installed

9_24_2012_11_26_48_pm.jpg

Posted on Sep 24, 2012

TDISLine
  • 1874 Answers

SOURCE: timing balance shafts on 2az

1. Remove the fan and generator V belt:

tdisline_502.jpg
tdisline_503.jpg
2. TIMING CHAIN (2az-FE Engine):
Before servicing the vehicle, refer to the Precautions Section.

Drain the engine oil.

Remove or disconnect the following:
Negative battery cable

Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:

  1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.
  2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley

tdisline_504.jpg
Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine

tdisline_505.jpg

Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine


  • Remove or disconnect the following:

    Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner
  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:

    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • tdisline_506.jpg
    Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine

    tdisline_507.jpg
    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    1. Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.
    2. Remove the bolt, chain tensioner and spring.
    3. Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    1. Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top.


    tdisline_508.jpg


  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine

  • Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.
  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_509.jpg

    Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine

    tdisline_510.jpg

    Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine

    tdisline_511.jpg
    Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine

    tdisline_512.jpg

    Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine

    tdisline_513.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    Posted on May 12, 2011

    • 1 Answer

    SOURCE: toyota tarago 2az fe motor

    Rustam.Where is the fuse for radio of 2003 toyota tarago

    Posted on Jan 24, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    2006 nissan altima 2.5 balance shaft assembly timing


    Before I replaced the balance shaft assembly chain on my 2004, the marks on the chain weren't lined up with the marks on the sprocket. When I installed the new chain, I just lined up the marks. (Had to rotate balance shaft independent of crankshaft to do this) Wasn't any noticeable vibration before or after, not really sure why the marks weren't lined up before.
    Hope this helps.

    Apr 15, 2015 | 2006 Nissan Altima 2.5

    1 Answer

    Timing chain marks needed for Audi A4 B9 1.8tfsi 2009 model. Engine was taken out and settings not marked. This is extremelyurgent. Please help


    diagrams I have show a twin cam set up with 2 balancing shafts. The marks on the cam shaft point to (left cam shaft 11 oclock the mark on the right point to the 1 oclock position. The chain will have 3 black links-- the top black links will be at the timing marks on the shafts with the 3rd black link directly at 6 oclock facing a mark on the gear. The balancer marks both point to the 1 oclock position with black links on each and the 3rd black link will be facing a mark to the 7 oclock position on the crankahaft gear. Everything is done with the piston at TDC no 1 cylinder so get it there before you put the cam shafts in position or you will bend valves. Crank shaft gear is not keyed to the crank shaft. there are dots on the right hand balancer shaft gears and these dots will be as the 2 dots on adjacent teeth either side of a dot on the meshing gear. I suppose that is all as clear as mud but if you got this far then you will see the marks and marked links on the chains

    Dec 22, 2013 | Cars & Trucks

    1 Answer

    BALANCE SHAFT SETUP MARKS FOR TOYOTA 2AZ-FE MOTOR


    A LOT OF SHOPS ARE HAVING TROUBLE SETTING THE BALANCE SHAFTS ON THE 2AZ-FE (AND IF YOU ARE ONE TOOTH OFF YOUR ENGINE WILL BLOW UP ) I AM A TOYOTA TECH AND HAVE SEEN THE DAMAGE THAT INCORRECT BALANCE SHAFT TIMING CAN CAUSE THERE IS A TOOL COMPANY CALL (TIMING SOLUTIONS) THE TOOL IS CALLED (THE 2AZSAVER) THIS TOOL COMES IN A CASE WITH VERY DETAILED VIDEO ON HOW TO PROPERLY SET BALANCE SHAFT TIMING ,THIS TOOL MAKES SETTING BALANCE SHAFTS VERY EASY

    Feb 18, 2013 | Toyota Camry Cars & Trucks

    1 Answer

    Where can I get the diagram to set the balance shaft marking for a Toyota 2az engine


    hi check this image out, i just got this for you.
    http://www.gto-northwest.co.uk/forum/download/file.php?id=111&t=1
    you will also find a larger image of the diagram with it.

    Nov 19, 2012 | Cars & Trucks

    1 Answer

    Timing balance shafts on 2az fe toyota


    Take a look at the engine below with chain installed

    9_24_2012_11_26_48_pm.jpg

    Sep 24, 2012 | 2003 Toyota Camry

    1 Answer

    I need timing marks on 2.2 toyota camry 2000


    1. Remove the fan and generator V belt:
    tdisline_542.jpg

    tdisline_543.jpg 2. TIMING CHAIN (2az-FE Engine):
    Before servicing the vehicle, refer to the Precautions Section.
    Drain the engine oil.
    Remove or disconnect the following:
    Negative battery cable
    Hood Right-side front wheel Engine under covers Right-side fender apron seal Front exhaust pipe Engine moving control rod and bracket Right-side engine mounting stay and bracket Accessory drive belt Engine appearance cover Engine wire Alternator Power steering pump, leave the hoses connected Ignition coils Ventilation hoses Cylinder head cover Turn the crankshaft pulley to set the No. 1 cylinder to TDC compression. Align the groove on the pulley with the timing mark -0- on the front cover. Remove the crankshaft pulley as follows:
    1. TMC made: Use Special Tool 09213-54015 to hold the pulley to loosen the bolt. Use Special Tool 09950-50013 to remove the bolt and pulley.

    2. TMMK made: Use Special Tool 09960-10010 to hold the pulley to remove the bolt. Use Special Tool 09950-40011 to remove the crankshaft pulley
    tdisline_544.jpg Fig. Removing the crankshaft pulley-TMC-2.4L (2AZ-FE) engine
    tdisline_545.jpg

    Fig. Removing the crankshaft pulley-TMMK-2.4L (2AZ-FE) engine

    Remove or disconnect the following:
    Crankshaft position sensor Lower oil pan No. 1 chain tensioner Accessory drive belt tensioner

  • Support the engine with a suitable engine lifting device.
  • Remove or disconnect the following:
    Engine mounting insulators Right-side engine mounting bracket Stud bolt for the accessory drive belt tensioner from the block Front cover mounting bolts and nuts Front cover Crankshaft position sensor plate Timing chain tensioner slipper Timing chain vibration damper Timing chain Crankshaft timing sprocket
  • Turn the crankshaft counterclockwise by 90°, and align an adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
    tdisline_546.jpg
  • Fig. Align the adjusting hole of the oil pump drive sprocket with the oil pump groove-2.4L (2AZ-FE) engine
    tdisline_551.jpg

    Fig. Insert a bar to lock the sprocket in position-2.4L (2AZ-FE) engine
    Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Remove the nut.

    Remove the bolt, chain tensioner and spring.

    Remove the chain tensioner, oil pump sprocket and No. 2 timing chain.

    To install:
    Set the crankshaft key into the left horizontal position. Turn the cutout of the drive shaft to the top

    tdisline_552.jpg

  • Fig. Align the crankshaft key and drive shaft cutout as shown for installation-2.4L (2AZ-FE) engine
    Align the yellow colored links with the timing marks of the sprocket as shown in the illustration.

  • Insert the sprockets with chain to the crankshaft and oil pump shaft.
  • Temporarily tighten the oil pump driven sprocket with the nut.
  • Insert the damper spring into the adjusting hole, and install the chain tensioner plate with the nut. Tighten to 9 ft. lbs. (12 Nm).
  • Align the adjusting hole of the oil pump driven sprocket with the groove of the oil pump.
  • Put a bar in the adjusting hole of the oil pump driven sprocket to temporarily lock the sprocket in position. Tighten the nut to 22 ft. lbs. (30 Nm).
  • Rotate the crankshaft counterclockwise by 90°, and align the crankshaft key to the top.
  • Install the timing chain vibration damper. Tighten to 80 inch lbs. (9 Nm).
  • Align the timing marks of the camshaft timing sprockets and bearing caps.
  • Using the crankshaft pulley bolt, turn the crankshaft and set the set key on the crankshaft upward.
  • Align the gold or orange colored link with the timing mark of the crankshaft timing sprocket.
  • Using Special Tool 09309-37010, tap in the sprocket.
  • Align the gold or yellow colored links with the timing marks of the camshaft timing gear and camshaft timing sprocket. Install the chain.
  • tdisline_553.jpg Fig. Align the marks of the sprockets and bearing caps to set the No. 1 cylinder at TDC-2.4L (2AZ-FE) engine
    tdisline_554.jpg Fig. Set the crankshaft set key facing upward-2.4L (2AZ-FE) engine
    tdisline_555.jpg Fig. Align the marked link of the timing chain with crankshaft sprocket timing mark-2.4L (2AZ-FE) engine
    tdisline_556.jpg Fig. Tap the crankshaft sprocket in with Special Tool 09309-37010-2.4L (2AZ-FE) engine
    tdisline_557.jpg Fig. Align the marked links of the timing chain with the camshaft sprockets during installation-2.4L (2AZ-FE) engine

    May 21, 2011 | Toyota Camry Cars & Trucks

    1 Answer

    2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


    To Install:
    1. Install balance shaft drive gear onto the left camshaft.
    2. Install the camshaft sprockets and new bolts finger tight.
    3. Using a vise, compress the timing chain tensioner plunger.
    4. Install a retaining clip on the tensioner to hold plunger IN during installation.
      marking timing chain a0038720.gif

    5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
    6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
    7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
    8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
    9. Position the crankshaft using the special tool. Then remove the tool.
      Crankshaft special tool positioning n0013602.gif

    10. Install the crankshaft sprocket with flange facing forward.
      Crankshaft sprocket timing mark n0011528.gif

    11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
    12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
      Left camshaft sprocket timing mark a0080774.gif

    13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
      Crankshaft sprocket timing mark a0079624.gif
    14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
      Right camshaft sprocket timing mark a0041104.gif

    15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
    17. Remove the retaining clips from the right and left timing chain tensioners.
    18. Verify alignment of all timing marks.
    19. Install crankshaft sensor ring on crankshaft.
    20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
    21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
    22. Align the chalk mark on the balance shaft with the camshaft timing mark.
      Balance shaft bearing caps n0007112.gif

    23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
    24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
      • Step 1-30 ft-lbs (40 Nm)
      • Step 2-tighten an additional 90 degrees
    25. Position the crankshaft keyway in the 11 o'clock position.
    26. Lubricate and install all camshaft roller followers. WARNING
      Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

    Oct 07, 2010 | Ford F-250 Cars & Trucks

    1 Answer

    In your field


    Hi,

    Sorry, doon sa request ako naunang nakapost.

    If the client overhauled the engine, removed the crankshaft and the balance shaft with the balance shaft chain, and did not mark it before hand, no way that I know he can align/time it.

    To my knowledge, the best possible solution is to buy an aftermarket or original chain which then has markings and illustrations/diagrams for the timing as well as instruction set.

    Even the service manual is vague on this since the factory installed chain has no markings (which perhaps may be the reason his timing is now off).

    Good luck.

    Aug 20, 2008 | 2002 Toyota RAV4

    2 Answers

    Correct timing of balance shaft the engine vibrate


    i'm sorry, that would be beyond my knowledge of expertice.
    but i would refer you to a good friend of mine.
    i would forward this post and see if he can help you with your problem..

    tnx for asking me,

    drcool

    Aug 19, 2008 | 2002 Toyota RAV4

    2 Answers

    Toyota tarago 2az fe motor


    Rustam.Where is the fuse for radio of 2003 toyota tarago

    Jul 05, 2008 | 2003 Toyota Camry

    Not finding what you are looking for?
    2006 Toyota Camry Logo

    Related Topics:

    487 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75817 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8180 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...