Question about 2001 GMC Yukon

Open Question

Idler arm pitman arm tie rod end diagram - 2001 GMC Yukon

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: looking for picture of front chassis assembly for

yes

Posted on Mar 15, 2010

  • 1 Answer

SOURCE: want to know what the torque specs are for the

2000 gmc jimmy front cv axle nut (36 mm) torque ratings?

Posted on Jul 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many lubrication fittings are there on a 1999 Buick LaSabre?


if this has a conventional front end(not front wheel drive) then there will be one on each outer tie rod end one on each inner tie rod end, both upper and lower ball joints on each side, idler arm and pitman arm. if its front wheel drive it will have a rack and pinion steering. there for there will be one on each outer tie rod end and one on each lower ball joint, if they have grease fittings. so conventional steering has 10 fittings total and rack and pinion has 4 total.

Jul 28, 2015 | Buick Cars & Trucks

1 Answer

How to change front end on 94 gran marquis


Front end is a pretty vague description of what you are trying to do. There are - shocks -lower ball joints -upper ball joints -inner tie rod ends -outer tie rod ends -idler arm -pitman arm -center link -stabilizer links -stabilizer bars It is not likely that all of those need to be replaced at the same time?

Apr 10, 2013 | Cars & Trucks

1 Answer

I need to replace inner and outer tie rods and Idler arms. Is there a diagram?


The inner and outer tie rods are pretty self explanatory remove the nut from the knuckle. Whack the knuckle a couple times where the tie rod goes through and the tie rod will pop out. The inner will releas the same way. Get the sleeve whe you get the inner and outer tie rod. It will make life a lot easier. Assemble the new parts to the approximate same length as the parts you removed and install. The idler arm will be bolted to the frame and then have a ball and socket that will be removed in the same manner as the tie rod end. The pitman arm will require a puller to seperate it from the gear box. Sometimes you have to heat up the end that attaches to the gear box to get them to pop. Sometimes the gear box needs to be removed in order to get the puller on the pitman arm. Lower and upper ball joints are also very common on these. If they have not been done I would have them checked as well.

Aug 07, 2012 | 2000 Chevrolet Blazer

1 Answer

Idler arm LF,idler bracket LF,pitman arm LF,tie rod sleeve LF, inner tie rod LF, tie rod end LF, need to repair


you will need a pitman arm puller, tie rod separator and a good set sockets(6 point preffered)and some penetrating oil, measure all distances between points before removal,and get the vehicle aligned

Dec 01, 2010 | 1995 Chevrolet Tahoe

2 Answers

My 94 Silverado pulls very hard to the right, and is eating up my front left tire like nothing. what other than alignment can be going wrong?


You could have a bad tie rod end, Idler arm, pitman arm, wheel bearing or ball joint. All of these will normally cause a vibration also. Check by jacking the front end one side at a time and moving the tire back and forth on front and back and in and out on top and bottom. Either watch or have someone else watch the steering assembly for movement and where it is. If there is no unusual movement, it is more than likely an alignment problem or tire problem.

Oct 20, 2010 | 1994 Chevrolet C1500

1 Answer

Is a special tool required to remove inner tie rod from relay rod on 2001 Tahoe.? Also what should torque be?


Relay Rod Removal & Installation To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Engine protection shield, if equipped
    • Steering damper from the relay rod, if equipped Note: Use the proper tool in order to separate all the tie rods and the ball joints.
      Steering components gm_trk_sub15_steering_components.gif

    • Tie rod ends (F) (See: Tie Rod Ends)
    • Idler arm ball stud nut (J) and discard the nut (See: Idler Arm)
    • Pitman arm nut (H) and discard the nut (See: Pitman Arm) Remove the idler arm from the relay rod gm_trk_sub15_idler_from_relay_rod.gif

    • Relay rod from the idler arm ball stud using the J24319-B or other suitable puller Remove relay rod from pitman arm ball stud gm_trk_sub15_relay_rod_rem.gif

    • Relay rod from the pitman arm ball stud using the J24319-B or other suitable puller
    • Relay rod from the vehicle
  3. Inspect the threads on the tie rod ends for damage
  4. Inspect the ball stud threads for damage
  5. Inspect the ball stud seals for excessive damage
  6. Clean the threads on the ball studs
To Install:
  1. Install or connect the following:
    • Relay rod to the vehicle
    • Relay rod to the pitman arm ball stud
    • Relay rod to the idler arm ball stud and make sure the seal is on the stud
    • New pitman arm prevailing torque nut
    • New idler arm prevailing torque nut and tighten the idler arm and pitman arm nuts; Torque to: 46 ft. lbs. (62 Nm)
    • Tie rod ends
    • Steering dampener to the relay rod, if equipped
    • Engine protection shield, if equipped
  2. Lower the vehicle
  3. Check the wheel alignment
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Sep 18, 2010 | 2001 Chevrolet Tahoe

1 Answer

How to replace a idler arm and pitman arm need to replace it on my 98 gmc suburban 4x4


You will need the proper tools to remove them which can be rented at auto parts stores. The pitman arm has to pulled off with an pitman arm puller also have to drop steering box I believe to change it. I know we did on my 1996 Tahoe the idler arm can be seperated with a front end fork also available at parts store. You just drive it between the idler arm and tie rod after removing castle nut and cotter pen.

Jul 17, 2010 | 1998 GMC Suburban

1 Answer

How to change the pittman arm and idler arm on a 1999 S10 Chevy Blazer 4x4?


Pitman arm requires a pitman arm puller, and a tie rod seperator or "pickle fork". Remove the cotter pin on from the joint on the pitman arm and center link, then remove the nuts from both ends of pitman arm. Use the pitman arm puller to remove the pitman arm from the steering gear, then use the tie rod seperator to remove the end from the center link. Reinstall and retighten nuts, do not leave out the cotter pin.
Idler arm will require tie rod seperator. Remove the cotter pin from the end at the center link, use the tie rod seperator to seperate the joint there. Unbolt the idler arm from the frame, and remove. On reinstalling remember to install a new cotter pin. It would be best to have the front end alignment checked after replacing these parts.

Apr 08, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

Repair steering linkage


You'll have to rent or borrow a pickle fork and a pitman arm puller. There is more than one size of pickle fork so specify for tie rod ends. You can buy them too, about $100 for the pair and they are not vehicle specific.
Jack and block up your front end so the wheels are clear. Take the nut off the tie rod end and wedge the pickle fork between the tie rod and the drag link, rap with a hammer until it separates. Loosen the bolt on the collar and unscrew the tie rod end. Count the turns when you remove it and screw the new one in the same number of turns.Fit it into the drag link and tighten the collar and the new nut.
Take the nut off the idler arm and use the pickle fork to separate it from the drag link. Unbolt the idler arm from the frame. The new one goes on in the reverse.
You'll probably need an adjustable wrench to remove the nut from the pitman arm,it's bigger than most wrench sets. Separate it from the drag link first. Slide the puller on and tighten it up. Once it starts to turn hard, give the bolt on the puller a rap with the hammer and tighten some more. Repeat until the arm comes off. Slip the new one on and tighten.
Don't be shy when you tighten these parts because if there is play, the holes in the drag link will oval out and you will have to replace it too. Don,t use a pickle fork on the pitman arm or you will have to replace the seal in the bottom of the steering box. Hope this helps.

Jul 08, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

I ned to know / see the diagram of the 2000 2500HD chevy pu . I need to get the parts for a friend he was told - he needs the pitman arm and idler arm I have not seen the truck yet but would like to see...


napa online lists two pitman arms for $49, $89 depending upon spline count. As a photo wont give you this info, it may not help...As far as I can see, they list the other components as well but I didn't look at prices. To remove the pitman arm you will need a good pitman arm puller...some of the larger parts houses rent them out. You will not get it off the steering box without one!!
good luck!
(maybe your friend will buy you a beer when you're done!!!)
need any techncal help along the way, I'm here!!

Apr 18, 2009 | 2003 Chevrolet Silverado 2500HD

Not finding what you are looking for?
2001 GMC Yukon Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...