Question about 2000 Isuzu Trooper

Open Question

Starting problem Hi, I have a 2000 Isuzu 3.0 DOHC DT that has developed a starting problem. When first starting ( this could be in the morning or after it has been standing for about 2 hours) the engine turns over but dose not fire. The only way it starts is if u leave the key in the ON position for 15-20min, after witch it starts up fine. Some times it will stall while driving but starts right up again as if there is no problem. Has anyone had a problem like this? I will appreciate any ideas to what the problem might be. Thank's

Posted by on

  • Clint Lithgow Sep 17, 2013

    Thank you, have solved this problem. It was the camshaft sensor that was falty. Also a tip when fitting the sensor, if the car dose not start after fitting the new sensor. Turn it by a few degrees till it starts up. The sensor has to be in a certen position. Cheers

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We live in New Zealand and own a 1998 Isuzu Bighorn, 3.0D. About 3 months ago it started idling roughly and stalling just after starting. Then it stalled on me when I was driving 70kph. It also has no


wow first post ever posting country ,what a brave person. !!!!
welcome to USA forums ,that have no such car.(truck)
the line up. (wiki list) so its 3.0L 4JX1
stalls and lost power.
The 4JX1 is a 3.0L direct injection diesel engine, turbo, some intercooled, which replaced the 4JG2 in the Isuzu Bighorn/Trooper/Holden Jackaroo. It uses unit injectors and 4 valves per cylinder.

can be caused by many reasons. get it scanned yet. ?
or see FSM book on flash codes from the direct injection fuel
controller? (per this engine option and market)

does turbo have proper boost? (PSI boost or +1 bar boost?)
does it even have a boost gauge.?
there are over 50 causes, of stalls (most inside engine)
but its not getting boost or the injection rates are wrong.
there are basic tests for each covered in the FSM
Factory (oem) service manual, with coverage for this engine.


3.2 L 6VD1 SOHC V6
3.2 L 6VD1 DOHC V6
3.5 L 6VE1 DOHC V6
3.0 L 4JX1 TD I4
3.1 L 4JG2 TD I4

Feb 15, 2015 | Isuzu Cars & Trucks

1 Answer

My 2000 isuzu trooper 3.0 dohc is very smokey in the morning after a short drive its grand


valve guide seals could be bad or rings could be getting worn or could need tune up

Dec 19, 2013 | 2000 Isuzu Trooper

1 Answer

What are some symptoms of a bad timing belt on a 1997 eagle talon 2.0 DOHC


Bad starting, and Poor engine performance. If the Belt is causing this much trouble, I would be getting it replaced like yesterday.
Regards,DT

Feb 15, 2011 | 1997 Eagle Talon

1 Answer

What is the firing order for a 1998 isuzu rodeo 2.2 4 cylinder


For the 3.2l dohc v6 it is 1,2,3,4,5,6. with the cylinders being numbered from front to back and left to right 1,3,5,right and 2,4,6 left. The left and right side of the vehicle is determined from you setting in the drivers seat For the 2.6l 4cyl it is 1,3,4,2 starting with the right front wire and going in counter clockwise direction, and the cylinders are numbered from front to back 4,3,2,1.

Aug 16, 2010 | 2000 Isuzu Rodeo

1 Answer

Firing order for a 2000 isuzu rodeo v6 2 wheel drive


2000 Isuzu Rodeo LSE 2WD 3.2 liter DOHC V-6

7fa2a6a.gif


Hope helps (remember rated this).

Jul 19, 2010 | 2000 Isuzu Rodeo

1 Answer

Serpentine belt routing 1999 Ford Escourt 2.0 DOHC


Belt ribs under the Bottom pulleys, Ribs over the Top pulley and the Flat side inboard to the Tensioner Pulley. May sure everything is lined up on completion before starting the engine. Regards,DT

Aug 29, 2009 | 1999 Ford Escort

1 Answer

I pulled the 3 wires out of the plug on my 98 isuzu trooper and dont know how thay go back in order can you help me plz


For the 3.2l dohc v6 it is 1,2,3,4,5,6. with the cylinders being numbered from front to back and left to right 1,3,5,right and 2,4,6 left. The left and right side of the vehicle is determined from you setting in the drivers seat For the 2.6l 4cyl it is 1,3,4,2 starting with the right front wire and going in counter clockwise direction, and the cylinders are numbered from front to back 4,3,2,1. hope this helps out

Jul 05, 2009 | 1998 Isuzu Trooper

1 Answer

ISUZU 1999 / 2000 3.0 WONT START BREAKING PARTS 07962121933


hi i have a isuzu trooper 3.0 td 2000 w plate when i go to start it in the morning the batteries are flat ill push it and jump start it park it up it will be ok all day long then but i go to start it in the morning same problem we put new injectors on new heater plugs new alternator had the battderies tested both are exelent batteries why is this could u please contact me on 07557105273

Dec 15, 2008 | 2000 Isuzu Trooper

Not finding what you are looking for?
2000 Isuzu Trooper Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...