Question about Mercury Grand Marquis

Open Question

Remove rear bumper on 08 mercury grand marquis

Rear bumper removal

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

eitan
  • 291 Answers

SOURCE: remove the rear bumper

Removing Prowler Rear Bumpers First remove the four 10 MM bolts holding the trans cooler and drop it down. Support it by attaching one bolt to the lower hole on the cooler frame. This will keep the weight off the lines. This takes two min. and allows easy removal of the elect. lines. Then remove the four bolts on each bumper. The bolts are 13MM and 17MM. You will need a ratchet, sockets, extension and a 13MM open end wrench. If you remove the rear bumpers, you should replace the rear pan with one of the aftermarket ones otherwise you will have big holes staring at the people behind you. Go to prowleronline.com and check the vendors for a couple of options. Maybe you are removeing them to paint and reinstall. Look at this link for some options .. Mine is the 7th post down. http://www.prowleronline.com/ubb/Forum1/HTML/014949.html Hope this helps.

Posted on May 15, 2008

  • 99 Answers

SOURCE: Remove rear plastic bumper cover

please email me at meanness628@aim.com with any other info or questions if you have already gone to a body shop

Posted on Sep 29, 2008

  • 1986 Answers

SOURCE: how to remove the egr valve on a 1993 mercury

Jack up the passengers side of the car, get a 1 1/16" wrench break loose the fitting to the manifold, hold a 24 mm wrench on the fitting to the manifold, loosen the flare nut on the tube. Then using a 10 mm socket, about 2 inches long, loosen the two nuts under the EGR valve, then take the both out, remove the vacuum hose to the top of the EGR valve, and the sensing line from the small tube. then completely remove the flare nut from the orifice fitting on the manifold. BE CAREFUL with the tube, do not bend it or break it, you may find PB blaster useful the night before on a cold engine loosen these fittings. Once the EGR valve is out, remove the orifice out of the manifold, remove the tube from the EGR valve, again be careful, mark the tube to EGR position before pulling this off, because the top fitting to EGR needs tightened before you put it back in, it will make the lower fitting difficult if you do not line it up right, dry fitting from under the car is helpful, mark it, and then tighten the top. Clean out the tube, be careful not to bend the little tube, either inside or outside the larger tube, it sticks out inside. Clean the orifice, clean the manifold face carefully not to score it, check for blockage there too. Apply anti-seize to the orifice, put it back in the manifold, then apply anti-seize to the bolts for the EGR valve, and the flare nuts both ends. Apply some silicon to the EGR valve face, just enough to hold the gasket in place, put the new gasket on, start the bolts two turns in the gasket, it will hold them in place, then start them in the manifold, then start the lower flare fitting to orifice, tighten the top bolts, and then the flare nut, connect the vacuum line, connect the sensing line. I just recently did this process, it works, if have other EGR issues, the valve is the easiest.

Posted on Oct 13, 2009

bschilz
  • 2049 Answers

SOURCE: how do i remove the serpentine belt on a 92

First, keep a copy of this diagram as you will need it when you go back to putting it on…

8804e31.jpg

Here’s a link to a “how to” video that will walk you through removal and replacement of your serpentine belt.

Posted on Jan 19, 2010

drsinister69
  • 2317 Answers

SOURCE: how to remove rear axle shaft on 2001 grand

Jack up the rear of the vehicle. Remove the rear end cover. Usally there will be a bolt that holds a round steel pin thru the differential. Remove the pin, you should be able to then push the axle towards the middle of the rear end to remove the c type clip that prevents the axle from coming out, then side out the axle.

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How To Install Replace Rear Door Panel Mercury Grand Marquis 98-02 1AAuto.com


How To Install Replace Rear Door Panel Mercury Grand Marquis 98-02 1AAuto.com

on May 22, 2012 | 1998 Mercury Grand Marquis

Tip

How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02...


How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02 1AAuto.com

on May 22, 2012 | 2001 Mercury Grand Marquis

2 Answers

2008 ford escape. removal of rear bumper cover


Pop the Hatchback open and remove the connectors
from the top of the bumper cover.

Optional Step: Using a Floor Jack, raise both sides
of the car in the back, supporting both sides with
jack stands, and remove the rear wheels.

Using Torx Bits, remove the inner rear wheel well
lining.

Get behind the rear wheel well and loosen the bolts
holding the bumper brackets on. They're pretty
difficult to find and remove. Be Patient. Do the
same to the other side.

Remove the rear bumper cover by pulling the cover
outward from the part nearest the wheel on both
sides. Once removed, take off the 2 black mounting
brackets from the bumper cover.

Good Luck

Feb 27, 2015 | 2008 Ford Escape

1 Answer

How do I replace the rear axle assembly in a 2000 Mercury Grand Marquis?


If you have air suspension, turn it off from the trunk. Put car on hoist and support rear axle. Make sure you support the axel well so the coil springs do not injure you when you remove the shocks and etc. Remove brake lines from brakes. Remove emergency brake cable from brakes. Remove sway bar link bolts to frame. Remove the bolts that hold axle to rear control arms. Remove rear shocks. ( these are a real pain ) Axle assembly can now be removed.

Feb 09, 2015 | 2000 Mercury Grand Marquis

Tip

How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02...


How To Install Replace Rear Inside Door Handle Mercury Grand Marquis 98-02 1AAuto.com

on May 22, 2012 | 1998 Mercury Grand Marquis

Tip

How To Install Replace Side Rear View Mirror Mercury Grand Marquis 98-11...


How To Install Replace Side Rear View Mirror Mercury Grand Marquis 98-11 1AAuto.com

on May 18, 2012 | 1998 Mercury Grand Marquis

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

1 Answer

Where does the top part of shock mount on 1990 mercury grand marquis?


Strut tower in plain site, if you open the hood,
should have 3 nuts to remove for top bearing plate

The rear ones may be in the trunk

Jan 22, 2013 | 1990 Mercury Grand Marquis

2 Answers

How to remove rear bumper 1999 blazer


Hi there:
Check this Removal Procedure...

6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 1999 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...