Question about Cars & Trucks

Open Question

How to replace timing belt diagram on mazda astina hatch 2003

My mazda 323 astina auto hatch needs a timing belt change has anyone goy a diagram to print

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
old marine
  • 1992 Answers

SOURCE: replace alternator belt 97 mazda protege

Here's the page from the AutoZone online manual for replacing drive belts.

Posted on Mar 10, 2009

Ad
  • 1 Answer

SOURCE: Timing Belt Replacement+Diagram

How to replace engine belt 1999 ford escort

Posted on Jul 08, 2009

  • 4369 Answers

SOURCE: need belt diagram for a 1998 ford escort zx2

Here it is. 13mm wrench to rotate tensioner

718d98e.gif

Posted on Feb 07, 2010

duane_wong
  • 6826 Answers

SOURCE: belt replacement diagram 2000 mazda mpv

REMOVAL & INSTALLATION Because serpentine belts use a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than it used to be on engines where accessories were pivoted and bolted in place for tension adjustment. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked'' all different ways through the pulleys) and to make sure the V-ribs are properly seated in all the pulleys. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.

  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys, and that the cooling fan cannot activate while servicing the belt(s). NOTE: Take a good look at the installed belt and make a note of the routing. Before removing the belt, make sure the routing matches that of the belt routing label or one of the diagrams in this book. If for some reason a diagram does not match (you may not have the original engine or it may have been modified), carefully note the changes on a piece of paper.
  2. For tensioners equipped with a 1⁄2 in. (13mm) square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently that it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from underneath the tensioner pulley itself.
  3. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioner's internal parts.
  4. Now finish removing the belt from the other pulleys and remove it from the engine. To install:
  5. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  6. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and make sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  7. Once the belt is installed, take another look at all the pulleys to double check your installation.
  8. Connect the negative battery cable, then start and run the engine to check belt operation.
  9. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment range. Fig. 1: Often the underhood label will display the serpentine drive belt routing 88231p43.gif
    Fig. 2: Relieve the belt tension by pivoting the automatic tensioner away from the belt, then remove the belt 88231p44.gif
    Fig. 3: Verifying serpentine belt alignment in the pulley 79244g60.gif
    Fig. 4: Fig. 1 Accessory V-belt routing (alternator) — Mazda MPV 3.0L engine 79244g67.gif
    Fig. 5: Fig. 2 Accessory V-belt routing (power steering) — Mazda MPV 3.0L engine 79244g66.gif
    Fig. 6: Fig. 3 Accessory V-belt routing (A/C compressor) — Mazda MPV 3.0L engine 79244g65.gif
prev.gif next.gif

Posted on Jul 08, 2010

  • 20 Answers

SOURCE: i need the diagram that

THE BEST THING TO DO IS GO TO AUTO ZONE OR ANY PARTS STORE AND PURCHASE A MANUEL FOR THAT VIHICLE COSTS ABOUT 28 DOLLARS WORTH THE WEIGHT IN GOLD

Posted on Oct 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i locate the flasher unit in a 1992 mazda astina hatch modelBG


This is normally under the dash on the drivers side. If you have the replacement part in hand it will help you identify it.

Jan 25, 2016 | 1992 Mazda 323

1 Answer

Instructions and or diagram on how to replace alternator belt for 97 mazda astina 323


This is from the Owners Handbook :
Alternator Drive Belt.
1. Loosen the alternator mounting bolt and adjusting bar bolt. Replace Fanbelt.
2. Turn the adjusting bolt until the correct tension is obtained. The deflexion should be 10mm.
3. Tighten bolts and recheck the tension.

Read more: http://wiki.answers.com/Q/How_do_you_replace_fan_belt_on_1997_Mazda_323#ixzz1yS0LNtO5

Jun 21, 2012 | Mazda Protege Cars & Trucks

1 Answer

Battery for 1997 Mazda 323 Astina 5dr hatch


It's fine to use a battery with a higher cold crank rating than original. Consider the rating in the manual to be a minimum requirement. You'll be fine as long as the physical dimensions and terminal placement are compatible with your car. The battery manufacturer's guide should tell you which battery fits your car.

Mar 03, 2009 | 1994 Mazda 323

1 Answer

My 99 Mazda Astina 323 (auto transmission) started making a rattling noise yesterday... went to my mechanic this morning and he said it was the timing belt. couldnt leave the car with him so drove home and...


have you thought about looking at the starter clutch, its possible that you need to have it replaced or a that the needs to be rebored, since it could be that your piston is what is knocking.

Dec 13, 2008 | Mazda 323 Cars & Trucks

2 Answers

Mazda astina water pump


It most likely runs off the timing belt. check there behind the timing belt cover.

Nov 25, 2008 | 1994 Mazda 323

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...