Question about Acura MDX

Open Question

How to replace driver side door handle acura mdx

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: relacing the inside driver side door handle

Its very easy to do, did mine today, pull the door panel off, 3 screws 2 on each corner of the bottom of the door and one in the grab handle tray. Look at the door handle there will be a small plastic circle that pops off remove plastic piece and remove screw, lift door panle upwards and off. 3 screws for the new door handle remove old one unclip door lock and unclip door handle install new one same way you took the old one off.

Part is $26.00 at kia, takes 15 minutes to repair!

Posted on Nov 06, 2008

Ad
  • 18 Answers

SOURCE: remote garage door opener

1-800-355-3515
www.homelink.com

1. Position vehicle within 10 feet of garage door- engine off and battery on.

2. Press/hold 2 outside buttons of Homelink transceiver until red indicator starts flashing rapidly, then release button. This should take about 20 seconds. This erases any previously learned codes.

3. Press/hold remote control and press/hold button of Homelink transceiver simultaneously. Slowly move remote control from 5" away to 1" away from Homelink transceiver. Release both buttons after red indicator starts blinking rapidly. This should take about 5 seconds. I discovered that the Homelink in my TL is a bit faulty because it took much longer to accomplish this than when programming the Homelink in my MDX. My TL's Homelink may "unlearn" it's code in the future and the needed proximity of the TL to the garage door may be much closer than desired until I get the Homelink fixed.

4. Press training button on garage door opener unit until the indicator lights illuminates- this should be immediate.

5. Within 30 seconds press/hold the Homelink button for 2-3 seconds until the red indicator starts flashing rapidly. Repeat a second time. It should now be programmed. Check it by pressing the programmed button on the Homelink receiver.

6. When programming more than 1 garage door opener unit, disconnect power from unit before programming more units. By not doing this the programmed unit could conflict with the unprogrammed units commands.

Problems:

1. The Battery in the garage door remote may be too weak to program Homelink. However, the battery may be strong enough to operate the garage door. One of my remote controls had a weak battery- my system was installed today, fresh out of the box. I had to use the second remote control for the programming of Homelink on my 2 vehicles.

2. Antenna on the garage door opener unit must be hanging down, fully extended.

Posted on Dec 08, 2008

  • 508 Answers

SOURCE: How to replace '96 Ford Explorer driver side exterior door handle

You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Posted on Feb 18, 2009

mcgyver468
  • 710 Answers

SOURCE: my 2001 acura mdx driver side door won't close

THE DOOR CATCH HAS A DOUBLE "C" THAT HOLDS THE DOOR CLOSED. FIRST TAKE A SCREWDRIVER INSIDE THE "C". USING THE HANDLE ON THE INSIDE, PULL THE HANDLE AS IF YOU WERE OPENING THE DOOR AND AT THE SAME TIME, OPEN THE DOUBLE "C" WITH THE SCREWDRIVER. I HOPE THIS HELPS. THANKS FOR USING FIX-YA. PLEASE FEEL FREE TO KEEP ME POSTED. GOOD LUCK

Posted on Sep 02, 2009

Testimonial: "it worked! thank you."

  • 1986 Answers

SOURCE: kia sedona outside door handle replacement

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to get to remove the bolts securing the outer handle on

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My remote will no longer open or lock my doors I have a 2002 Acura mdx I changed the batteries thinking that was probably the issue but still nothing.


The remote may have to be "re-trained" to your vehicle. The owner's manual should have the process listed. Probably having to sit in the driver's seat with the untrained remote while working the lock controls on the driver's side door.

Nov 21, 2016 | 2002 Acura MDX

1 Answer

Why can't I open the drivers side door from the outside


Linkage disconnected, handle is broken.

Jun 19, 2014 | 2004 Acura MDX

1 Answer

MDX Acura 2004 can't open the drivers side door from the outside


Remove the door panel and check the linkage and outer handle.

Jun 19, 2014 | 2004 Acura MDX

1 Answer

Can't open the drivers side door from the outside


Handle broken or linkage disconnected.

Jun 19, 2014 | 2004 Acura MDX

1 Answer

How to remove drivers door outside handle on a 2004 Acura MDX


Pop off the cover and remove the screws. 5 minute job.

May 30, 2014 | 2004 Acura MDX

1 Answer

How do i remove front door panel from 2003 acura mdx


Special Tools Required


  • KTC
    trim tool set SOJATP2014*

  • Trim pad remover, Snap-on A 177A or equivalent, commercially
    available
    *Available through the American Honda Tool and Equipment Program; call
    888-424-6857

    NOTE: Use the appropriate tool from the KTC trim tool set to avoid damage
    when prying components.
    1. Remove the
      mirror mount cover.
      Take care not to scratch the door panel.
    1. Remove the inner handle (A). Take care not to scratch the door
      panel.




      -1
      Pry out the cap (B), and remove the screw (C).




      -2
      Pull the inner handle forward and out half-way.




      -3
      Disconnect the inner handle rod (D) from the joint bushing (E), and power
      door lock switch connector (F). For some models: On driver's side, disconnect
      the driving position memory switch connector (G).

      -3
      NOTE: Check the bushing for damage, and replace if necessary.
  • Detach the clips (A) and hooks (B), then remove the speaker grille
    (C). Remove the screws (D).

    1. Detach the clips (A) and release the hooks (B), then remove the
      switch panel (C). Take care not to scratch the door panel. Disconnect the power
      window switch (door multiplex control unit) connectors (D). On driver's side,
      disconnect the power mirror switch connector (E).

    2. Pry out the cap (F), and remove the screw (G).

    1. Release the clips that hold the door panel (A) with a commercially
      available trim pad remover (B), then remove the door panel by pulling it upward.
      Disconnect the speaker connector (C).

      On driver's side, disconnect the front door subharness connector (D). On
      passenger's side, disconnect the courtesy light bulb socket (E), and detach the
      harness clip (F) from the panel.

      Remove the door panel with as little bending as possible to avoid creasing or
      breaking it.

    2. Install the door panel in the reverse order of removal, and note
      these items:
      • Check the clips for damage or stress-whitening, and replace them with new
        one.
      • Make sure the connectors are plugged in properly, and the inner handle rod
        and courtesy light bulb socket are connected properly.
      • Push the clips into place securely.
      • Do the power window control unit reset procedure.
      • Make sure the window and power door locks operate properly.
      • If equipped with driving position memory switch, check for proper operation.
    rjaai003_204.asp?menuid=rdbawh030000&sessionid=b23b61ec-6b2d-41dc-8d50-15026d64c21a&dbkey=s3u5a00j16126721401kdad01rjaai003_204.asp?menuid=rdbawh030000&sessionid=b23b61ec-6b2d-41dc-8d50-15026d64c21a&dbkey=s3v1a00j16126721401kdad03rjaai003_204.asp?menuid=rdbawh030000&sessionid=b23b61ec-6b2d-41dc-8d50-15026d64c21a&dbkey=s3u4a00j16126721401kdad01rjaai003_204.asp?menuid=rdbawh030000&sessionid=b23b61ec-6b2d-41dc-8d50-15026d64c21a&dbkey=s3u6a00j16126721401kdad01

    Sep 18, 2013 | 2003 Acura MDX

    1 Answer

    How to install the right mirror for accura MDX 2008


    You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then remove the bolts securing the mirror to the door

    Sep 17, 2009 | 2008 Acura Mdx

    2 Answers

    My 2001 acura mdx driver side door won't close


    THE DOOR CATCH HAS A DOUBLE "C" THAT HOLDS THE DOOR CLOSED. FIRST TAKE A SCREWDRIVER INSIDE THE "C". USING THE HANDLE ON THE INSIDE, PULL THE HANDLE AS IF YOU WERE OPENING THE DOOR AND AT THE SAME TIME, OPEN THE DOUBLE "C" WITH THE SCREWDRIVER. I HOPE THIS HELPS. THANKS FOR USING FIX-YA. PLEASE FEEL FREE TO KEEP ME POSTED. GOOD LUCK

    Sep 02, 2009 | 2001 Acura MDX

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    521 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Acura Experts

    yadayada
    yadayada

    Level 3 Expert

    76848 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you an Acura Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...