Question about 2004 Isuzu Rodeo

1 Answer

Turn key and it doesnt fire

2005 Holden rodeo. Turn key and it keeps turning over with out firing. I notice that the security light flashes when tring to start. Would this be an immobilizer problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 124 Answers

One way to find out. spray starting fluid in the intake then try to start. if it starts then your problem is fuel related.

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could keep my coil from firing ? I have the Ignition control signal and 12v. while cranking over engine at the top primary wiring of coil. Can you help me get spark?


Sounds like the security system is causing your problem. Is the "security" light flashing? If it is, turn the key on, leave the key in the ON position for 10 minutes. The light will stop flashing. Now, turn OFF the key, turn it back to ON, and then crank it. It should start. If the security light starts flashing again, go through the process again until it starts. This is resetting the security system after the battery has died, battery has been changed, radio was changed, instrument cluster was removed and replaced, etc. Hope this works for you.

Mar 29, 2016 | 2001 Chevrolet Silverado 1500

2 Answers

Security light on and won,t turn over engine to start . rolled car on to the roof on black ice. physically car looks ok


Car Won't Start Because of Anti-Theft System ... - RepairPal

repairpal.com > Problems > Oldsmobile > 88
Car Won't Start and Security Light is On on Oldsmobile 88 ... key turns over enginebut fails to start some times..security system keeps the fuel injectors from ...

Car Won't Start Because of Anti-Theft System ... - RepairPal

repairpal.com > Problems > Buick > LeSabre
Car Won't Start and Security Light is On on Buick LeSabre. Problems with the ... 1998 Buick LeSabreVisitor. Turn key on every thing come on but won't turn over.

Car Won't Start Because of Anti-Theft System ... - RepairPal

repairpal.com > Problems > Pontiac > Bonneville
Replaced trans, engine, PCM and bcm, now starter diabled- theft flashes on service ...1995 Bonneville car turns over but wont fire an security light is flashing car ...

GM Passlock Security Light Issues - RepairPal


Dec 26, 2015 | Cars & Trucks

1 Answer

2.6 Holden rodeo 90, new plugs leads rota an cap plus timing belt done today lined the timing up and it will fire up for few seconds, then die


If it stays on for 2 seconds it could be a security issue. Does the light stay on? If not I would check fuel pressure.

Jul 12, 2015 | Holden Cars & Trucks

1 Answer

Car will not start


What you say is very possible . The security (immobiliser) needs a constant transmission of signal to keep the system operational and if the battery in the key is nearly flat or loose then this flow of signal is intermittent and the immobiliser will eventually take control and shut down . Fit a new battery in the key and have it reprogrammed to the car.

Jan 09, 2014 | 1995 Isuzu Rodeo

1 Answer

I have 98 vt ex wagon V6 manual 5speed. Went to lock with remote would not lock, so key locked next morning car would wind over fire and die. Have had mechanic out and he has confirmed my security code...


sounds like the bcm may have failed, if so new bcm and new keys and programming with tech2
thats the worst case
or
wiring issue eg ignition switch
its not reading the key due to security light still flashing
the manual over ride should have worked if it didnt then i would be checking all fuses and power inputs to the bcm from the ignition switch

Sep 16, 2013 | 1998 Holden VT Commodore

1 Answer

2002 malibu 3100 v-6 won't start, getting fuel and fire to all cylinders


if the security light is flashing than the anti theft is active. The anti theft shuts down the injectors and will not let the vehicle start.

You'll need a battery charger to do this. Hook up the battery charger to the battery.

Place the key in the igniton and attempt to start. Let the key return to the run postion and leave it there untill the light stops flashing. Turn the key off

Turn the key on (do not try to start) and wait for the light to stop flashing again.

turn the key off and then try to start the vehicle.

You can google search "resetting gm security" and find this info as well.

Feb 03, 2012 | 2002 Chevrolet Malibu

1 Answer

I hav a rodeo 88 and when I turn on my lights the wipers come on when I remove the relay they stop


Sounds like a short if the light switch is on the turn signal swich the its the turn signal swith itself

Jan 05, 2012 | 2005 Holden Rodeo

1 Answer

I just changed the battery in my 2000 chev


You need to reset the security system. Turn the key on. The security light should be flashing. Leave the key on for 11 minutes. The security light should stop flashing. Turn the key off. Turn the key on. Leave the key on for 11 min. again. Do the process a third time. It should start and run on the next key turn. ( also hook a battery charger to the truck while doing this 30 min. procedure. If the battery goes low at any time you will have to start over.)

May 01, 2010 | 2000 Chevrolet Silverado

1 Answer

Reprogramming remote and key


if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Mar 26, 2009 | 2004 Isuzu Rodeo

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

658 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...