Question about 1987 Honda Prelude

1 Answer

Pedal assembly well i have an 87 honda prelude 2.0si, standard, and just realized today why the clutch failed and its the bracket holding the pedals in place. my question is, how do i get the bracket out?

Posted by on

  • 1 more comment 
  • James Dycke Mar 11, 2009

    the one that is hooked to the firewall

  • James Dycke Mar 11, 2009

    yes, its the bracket that holds those in place, but to get to it, i need to remove the pedals, how do i do so?

  • Greg Bernett
    Greg Bernett May 11, 2010

    Are you talking about the braket that is part of the clutch peddle?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 2,984 Answers

Http://img91.imageshack.us/img91/1206/pedal1op4.jpg

Please take a look at this and tell me if this is your problem.

Posted on Mar 11, 2009

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Can someone show me a picture of the clutch sensor on a 87 300zx


It's a switch hooked up to the top of the clutch pedal

Feb 19, 2015 | 1987 Nissan 300ZX

1 Answer

Yo I have a 1990 honda prelude si ,I have an issue with clutch pedal, my clutch pedal seems to stick when depressed it still has good pump pressure but I have to lift it up. Now I live in Idaho and it


The pedal return spring should be checked. Also the pedal bushings where pedal connects to the pedal support up under dash may be worn and not allowing free pedal movement. Work the pedal with your hand and watch the upper mounting of the pedal to see if you can see the problem. I would expect the bushings need replaced. You might try a little light oil where the clutch pedal attaches.

Jan 15, 2013 | 2000 Honda Prelude

2 Answers

How to adjust clutch pedal on 86 mustang lx


clutch is supposed to be self adjusting. Here are instructions for replacing the adjuster:


REMOVAL & INSTALLATION


See Figure 1

  1. Disconnect the battery cable from the negative terminal of the battery.
  2. Remove the steering wheel using a steering wheel puller, Tool T67L-3600-A or equivalent.
  3. Remove the lower dash panel section to the left of the steering column.
  4. Remove the shrouds from the steering column.
  5. Disconnect the brake lamp switch and the master cylinder pushrod from the brake pedal.
  6. Rotate the clutch quadrant forward and unhook the clutch cable from the quadrant. Allow the quadrant to slowly swing rearward.
  7. Remove the bolt holding the brake pedal support bracket lateral brace to the left side of the vehicle.
  8. Disconnect all electrical connectors from the steering column.
  9. Remove the 4 nuts that hold the steering column to the brake pedal support bracket and lower the steering column to the floor.
  10. Remove the 4 booster nuts that hold the brake pedal support bracket to the dash panel.
  11. Remove the bolt that holds the brake pedal support bracket to the underside of the instrument panel, and remove the brake pedal support bracket assembly from the vehicle.
  12. Remove the clutch pedal shaft nut and the clutch pedal, as outlined above.
  13. Slide the self-adjusting mechanism out of the brake pedal support bracket.
  14. Examine the self-adjusting mechanism shaft bushings on either side of the brake pedal support bracket, and replace if worn.

To install:
  1. Lubricate the self-adjusting mechanism shaft with motor oil and install the mechanism into the brake pedal support bracket.
  2. Position the quadrant towards the top of the vehicle. Align the flats on the shaft with the flats in the clutch pedal assembly, and install the retaining nuts. Tighten to 32-50 ft. lbs. (43-67 Nm).
  3. Position the brake pedal support bracket assembly beneath the instrument panel, aligning the four holes with the studs in the dash panel. Install the four nuts loosely.
  4. Install the bolt through the support bracket and into the instrument panel. Tighten to 13-25 ft. lbs. (18-34 Nm).
  5. Tighten the four booster nuts that hold the brake pedal support bracket to the dash panel to 13-25 ft. lbs. (18-34 Nm).
  6. Connect the brake lamp switch and the master cylinder pushrod to the brake pedal.
  7. Attach the clutch cable to the quadrant.
  8. Position the steering column onto the four studs in the support bracket and start the four nuts.
  9. Connect the steering column electrical connectors.
  10. Install the steering column shrouds.
  11. Install the brake pedal support lateral brace.
  12. Tighten the steering column attaching nuts to 20-37 ft. lbs. (27-50 Nm).
  13. Install the lower dash panel section.
  14. Install the steering wheel.
  15. Connect the battery cable to the negative terminal on the battery.
  16. Check the steering column for proper operation.
  17. Depress the clutch pedal several times to adjust the cable.
  18. 714c4a4.gif

Sep 24, 2010 | Ford Mustang Cars & Trucks

1 Answer

1999 honda prelude manual transmission isn't disengaging all the way when i shift, sometimes locking the shifter in gear or not allowing me to up or down shift. I know my master and slave cylinders need to...


This depends as dose it do it when cold or hot.
2nd when you push in pedal and put in gear dose it go in clean or hard to select 3rd can you hear a grinding noise when pushing in pedal and noise goes
when you take you foot off the clutch pedal IF so then its the thrust bearing on clutch REPLACE ALL .4th if you push in clutch pedal and select a gear and let the clutch out if drive right out (replace)

Sep 27, 2009 | 1999 Honda Prelude

1 Answer

93 honda prelude dohc vtec engine will not can be push started


Sounds like you accidently pulled the thin wire from you starter motor. Look at the connections at the end of the solenoid, mounted on starter motor.The thick red wire is Battery + next to that connection is a smaller male push- on terminal, locate loose wire (thin) in the same area and reconnect to male push-on terminal on solenoid or check if earth cable between body/battery to engine wasnt removed in the process.Also some vehicles you have to engage the clutch before starting, check for a switch located on clutch pedal where master cylinder connects to clutch pedal (Is clutch switch mounted and wiring connected?)

Jan 03, 2009 | 1993 Honda Prelude

1 Answer

Clutch pedal bracket on my 91 Honda Civic Broke.


http://www.honda-tech.com/showthread.php?t=1220898 shows exactly how to get the pedal bracket assembly out. Did you find a replacement bracket? If so, where?

Dec 29, 2008 | 1992 Honda Accord

1 Answer

1989 honda prelude s clutch problem, I can put the clutch pedal down, feels like its working ok, slave cylinder moves the clutch fork the normal distance, yet the clutch never disengages, i changed all the...


prolly a hydraulic problem master os slave cylinder leak ck your fluid takes dot 3 brake fluid , also you can put in gear hold the pedal down usually if the fiber substance is gone from the clutch disk the car will not move while cranking if the car moved then its a hydraulic problem , note to self try this with nothing in front of the car it might start up in gear if that happens you will have to immediately turn the engine key off , if the fiber is gone while running you can put trans into any gear while running without pedal inguaged , hope this helps

Dec 19, 2008 | 1989 Honda Prelude

2 Answers

Wont go into gear when engine running but will when not


Hi

What is happening is that the clutch is failing to disengage properly. There are two common reasons for this, one is the clutch thrust bearing starting to fail, and the other is that the clutch plate has become contaminated with oil either from the gearbox or the engine. The other possible reasons are that the clutch plate itself is starting to disintigrate, but that is usually accompanied by other symptoms, or that you've got something stuck under the clutch pedal which is preventing it going down far enough, but I guess you'd notice that.

Sadly the solution is usually expensive....

TJ

Nov 17, 2008 | 1991 Honda Prelude

3 Answers

Brake lights


Sounds like you need a new brake light switch. It is mounted to the brake pedal assembly.

Oct 26, 2008 | 1987 Honda Prelude

Not finding what you are looking for?
1987 Honda Prelude Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...