Question about 2000 Plymouth Neon

1 Answer

"done" on the odometer?

Tonight when I turned the car on it flashed "done" on the odometer twice and then disappeared. Is my poor car hollering stop??

Posted by on

  • leguh Mar 11, 2009

    Thank you very much! I am going to try to do that tomorrow & see if any codes do come up & pay attention this time!

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

If you turn the key on and off on a dodge 3 times in a row, they will give you trouble codes in the odometer area. After all the codes are displayed or if there are no codes it will say (done). There shouldn't be anything wrong with your car, it was just in diagnostic mode.

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset service warning lights


Turn key to position I

Then press and hold odometer button

Turn key to II and wait for the triangle to start flashing before releasing it whilst still flashing.

It makes a beep sound and the message disappears..

May 13, 2014 | 2006 Volvo XC90

1 Answer

Chrysler Crossfire will crank but not start. It starts fine when it's cold, but after driving around or making multiple stops, it will not start again. I have already changed the fuel pump relay


You can check codes on these without a scan tool ! surprised your mechanic doesn't know this ! Put the key in the ingition , turn it on then off , then on , then off then on again an leave it on . Then look at where the odometer is , will show P codes .
Flash Check Engine Light Codes Dodge Chrysler Jeep

Apr 21, 2017 | 2005 Chrysler Crossfire

2 Answers

How do you turn off the "Car needs Oil Change"



1. Make sure the trip odometer is NOT on 'Trip A' or 'Trip B' (ie: just the normal ODO). With the ignition off, press and hold the reset button. Press the 'Start' button twice without pressing the brake, but while holding the reset button. The dash will let you know its resetting, just keep holding the button until it is done.


2. Make sure the Trip/Odometer is set to "trip A". With ignition off press and hold the reset button. While pressing the reset button, press the start/ignition button twice to turn ignition on. Keep watching the trip/odometer display to flash the lines (-----) until you see it flash the zeros (00000) then it

Feb 22, 2011 | 2009 Lexus LS 460

2 Answers

Maint Reqd indicator light is on...I have 10K oil in; need to reset from 3k....How do I turn off?


On most cars you would turn on the ignition key, do not start the engine, press the gas pedal to the floor 3 times(if 3 times doesn't work, do it 5 times), turn the key off. When you start the car, the light should be off.

Dec 31, 2010 | 2008 Toyota Avalon

1 Answer

How do I reset the Maintenance Required light


hold in the trip odometer button , then turn key on, keep holding in the button, Watch the odometer section and it will count down the dashes. When the dashes disappear, its reset. Its a reminder to do maintenence at the indicated mileage. So it needs to be done.

Nov 09, 2010 | 2007 Lexus ES 350

2 Answers

Maintenance Lamp


Here's how you reset your maintenance light.

To reset the light,
Turn the ignition on
Make sure the odometer displays "ODO"
1.Turn the key off
2.Press and hold down the same button you use to get to "ODO"
3.Turn the key back to ON ( while still holding down the button)
4.Hold the button in until all the flashing lines on the odometer go away and the bunch of "000000" shows up and the maint reset light will turn off.
Your'e done.

If this doesn't work, you would have to try it on "trip A" instead of "ODO".

Oct 03, 2009 | 2006 Toyota Tundra

1 Answer

Maint req light


That just means you're due for an oil change. they automatically come on after 5000 miles. To reset the light, put it on the odometer display in your instrument cluster. turn the key off. now push and hold the odometer/trip reset button while you turn on the key to the IGN position. You will see 5 dashes on the odometer display, which will sequencially disappear and then go back to the odometer when it's done. after your odometer shows again, you can release the odometer/trip reset button and your maintenence light should be off.

May 31, 2009 | 2005 Toyota Tacoma

1 Answer

Signal light system problem


You have a bad ground somewhere .. try the rear lights first make sure each light is grounded good .. then try front ones and see if they are grounded also. Remove bulbs and replace them and make sure each is in good clean condition.. thanks Jerry holler if you have more

Jan 30, 2009 | 1997 Volkswagen Jetta

Not finding what you are looking for?
2000 Plymouth Neon Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

71162 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6992 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...