Question about 2005 Ford Excursion

Open Question

Reverse backup sensors for a 2000 ford excursion

I'am having problems with the reverse backup sensors.The light in
the button indicates that it's off.and I recently changed the sensors on the back bumper.what should I do next? NEED HELP PLEASE!

Posted by on

5 Suggested Answers

kalei02EXC
  • 62 Answers

SOURCE: how to replacew a backup sensor on a 2002 ford

It is very simple to replace the backup sensor. It is a good idea to put on safety glasses or goggles to keep dirt out of your eyes. The easiest way is to lay down under the back of the vehicle and reach up behind the the rear bumper and disconnect the pigtail electrical plug from the suspected faulty sensor(s). Then simply remove the sensor by pushing from inside of bumper toward the rear of the vehicle. If you are not sure which sensor is bad, and if only one sensor is bad, you should check one sensor at a time. And then with the good sensor in place you could test each sensor to see if the vehicle beeps while reversing towards a harmless object (like a traffic cone). Repeat this procedure with the other three sensors and leave the good sensor in place when the back up sensor system works correctly. Hopefully, this will FixYa!

Posted on Oct 10, 2010

moparownr
  • 667 Answers

SOURCE: how to find my keypad # on a 2000 ford excursion

You are Welcome and Thanks for the Rating in advance.

Posted on Apr 09, 2009

  • 1 Answer

SOURCE: how to change fuel filter 2000 excursion

Yes it is the tool for fuel lines and ac lines. Your local autoparts store should have them, they are universal. You need to use the small end for the fuel filter.

Posted on Jun 02, 2009

  • 64 Answers

SOURCE: where is the IAT sensor on a 2000 ford excursion

is it a as or diesel model?

Posted on Oct 05, 2009

  • 80 Answers

SOURCE: backup sensor problems

easiest way withoout a scanner is
verify that all wire connectors to back of sensors are not noticable damage, if so repair
if no damage, buy one sensor and trial each one with known good one til light is functioning properly.
very common for sensors to fail, so if want to fix you will need to buy one and all are the same so you can inner change

otherwise you will need scanned to determine which sensor is faulty

hope this helps
Jay

Posted on Jul 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What parts do i need for a tune up


if it is an EFI engine then the parts that you will need for a tune up will be indicated in the fault codes
The ECM of the vehicle continually tunes the engine while running ( around 100 times a minute) and as long as all the sensors are within parameters ,the engine will remain in tune
any sensors that are failing will leave a fault code and just because the engine light is not on doesn't mean that there are no fault codes recorded
basically "good mechanics do not fix what isn't broken"

Aug 31, 2015 | 2000 Ford Excursion

1 Answer

Clicking noise while driving.. But my turning signals n brake light work just fine . On my ford excursion 2000


have the cv joints checked as a clicking noise indicates that they need replacing

Jun 17, 2015 | 2000 Ford Excursion

2 Answers

C1230 code


Rear Speed Sensor Center Input Failure

Some type of abs speed sensor on rear diff

May be just dirty connnector

I googled it,would be here all night

Try Google ---2000 Excursion OBD2 Codes -C1230

Dec 02, 2012 | 2000 Ford Excursion

1 Answer

Have A 2000 excursion hade the hubs replaced and now have the ABS light going on off?


The ABS wheel speed sensors are on the hubs. Check the cable connectors are not loose and properly connected. Possibly one of the sensors might have been damaged when the hubs were replaced.

Jan 07, 2011 | 2001 Ford Excursion

1 Answer

How to replacew a backup sensor on a 2002 ford excursion


It is very simple to replace the backup sensor. It is a good idea to put on safety glasses or goggles to keep dirt out of your eyes. The easiest way is to lay down under the back of the vehicle and reach up behind the the rear bumper and disconnect the pigtail electrical plug from the suspected faulty sensor(s). Then simply remove the sensor by pushing from inside of bumper toward the rear of the vehicle. If you are not sure which sensor is bad, and if only one sensor is bad, you should check one sensor at a time. And then with the good sensor in place you could test each sensor to see if the vehicle beeps while reversing towards a harmless object (like a traffic cone). Repeat this procedure with the other three sensors and leave the good sensor in place when the back up sensor system works correctly. Hopefully, this will FixYa!

Sep 05, 2010 | 2002 Ford Excursion

2 Answers

I have a 2000 Ford Excursion. I went to hook up a


If these lights still work on your excursion then it is probably not a fuse problem. It sounds like it is a loose pin(s) with the trailer plug or a loose electrical connection(s) on the trailer or maybe the bulbs on the trailer are burned out. This should help, if not then contact me again at FixYa and I will be glad to help.

Jun 20, 2010 | 2000 Ford Excursion

2 Answers

Ford excursion 4x4 locks and wont unlcock


my4x4 is stuck and can't change back to 2w drive

Feb 09, 2010 | 2001 Ford Excursion

1 Answer

How to change the right front turn indicator bulb on 2004 excursion


1. Remove the front turn signal assembly mounting screws and slide the assembly forward, out of the vehicle body.

2.Twist the bulb socket a quarter turn counterclockwise, then remove the bulb assembly from the housing

3.The defective bulb can then be removed from the socket and replaced.

4. Installation of the front turn signal assembly is the reverse of removal.

Jan 21, 2010 | 2000 Ford Excursion

1 Answer

How to change the right front turn indicator on


1.Remove the front turn signal assembly mounting screws and slide the assembly forward, out of the vehicle body.
2.Twist the bulb socket a quarter turn counterclockwise, then remove the bulb assembly from the housing
3.The defective bulb can then be removed from the socket and replaced.
4. Installation of the front turn signal assembly is the reverse of removal.

Dec 31, 2009 | 2000 Ford Excursion

Not finding what you are looking for?
2005 Ford Excursion Logo

Related Topics:

377 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...