Question about 1997 Ford Ranger SuperCab

1 Answer

My 97' Ford Ranger does not blow cold air.Help??

My 97' Ford Ranger does not blow cold air. All other parts of the system works, When I turn the knob to A/C it only blows the outside temp. air. Please help me.... (Other details are... The heat works great and it blows on all modes and through all the vents that I choose.)

Posted by on

  • benjaminwhit Mar 11, 2009

    Yes I have, and it doesnt kick in at all. I have checked the power supply too and it is getting power.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

Have you checked to make sure your compressor is kicking in when turned to AC mode?

Posted on Mar 11, 2009

  • Mike Butler
    Mike Butler Mar 11, 2009

    Probably low on freon, or pressure switch faulty. Once freon gets low enough in the system, the compressor won't kick in. You'll have to have it checked & topped up. Keep in mind though, if it's low, there's abviously a leak somewhere. I Have had about 50/50 luck with AC system leak stop, if it's a small enough leak.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

AIR CONDITIONER FORD RANGER GOES HOT TO COLD AIR


Could be a blockage in the ac system, or a blend door problem.

Jul 04, 2012 | Ford Ranger Cars & Trucks

1 Answer

Compressor kicks on but no air


sounds more like a temp door is stuck feel the larger pipe for the ac while it is running if its cold you have a door problem

Jun 29, 2012 | 1999 Ford Ranger SuperCab

1 Answer

Cold air works fine but my heater does not blow hot air just cold in a 1993 ford ranger


check the cooling system to make sure the system is full.next check the temperature of the heater hoses when the car is at operating temperature.they should be the same temp,if one is not as hot as the other then the heater core is plugged and will need to be replaced.you can try to run clr through the heater core to see if it will unplug the heater.the other thing is the temp door will have to be checked to make sure its moving through out its full travel by moving the temp knob/lever and looking at the door arm to see it travel full range.this is located under the dash on the passenger side on the duct work.

Sep 18, 2011 | 1993 Ford F250

2 Answers

05 ford ranger 3.0......if I put my thermostat on cold...the vent blows hot air..on max ac..its cold air..makes no sense right....help


Cold air like, really cold or just cool. Sounds like your hot/cold blend door motor has perhaps failed with the blend door in the semi hot position. Blend door motor failure is very common on the Ford truck HVAC systems. Is is located behind the glovebox on top of the HVAC housing assembly.

May 19, 2011 | 2005 Ford Ranger

1 Answer

The fan works, air conditioning works, but the air wont heat up(knob turns to hot on thermostat). is it a vacuum hose problem, and how do we get to it?


The most common cause of this in the Ranger and the Explorer is that a part called the air temeperature control blend door acuator or the blend door shaft that the electric actuator moves has broken, this door is what shuttles between the heater core and the AC core and provides either heated or cooled air, or a blend of the two hot and cold air streams.

Dec 26, 2010 | 2008 Ford Ranger 2WD

1 Answer

1998 ford ranger 3.0. Heat does not work. Replaced thermostat then water pump. Still blowing cold air. Coolant streams out of the top of the coolant tank after engine is at operating temps. Temperature...


Hello did you flush out the cooling system while you had you coolant drained?this would be ideal to do at t hat time.Also be sure to bleed All air out of cooling system to avoid air lock.

Dec 25, 2010 | 1998 Ford Escort

1 Answer

When i turn on ac it works on max ac not on ac


You have a blend door actuator motor that is not working,they are hard to get to,the dash has to be removed,and pulled back toward the seats to access the actuator motor.

Jan 21, 2010 | 1998 Ford Ranger SuperCab

2 Answers

Heater blows cold air. I have replaced thermostat,


Not an expert by any means, but i know my ranger.. I had a small leak at the top of my radiator that still cooled the engine but didnt have enough pressure to get to the heater. The heater hoses travel up over the engine and just were not gettin anything to my heater core. That or make sure the heater control valve is operating.

Oct 26, 2009 | 1997 Ford Ranger SuperCab

1 Answer

Heater in truck blows either cold air or no air.


It sounds like you have air trapped in the cooling system. Try filling the radiator and coolant reservoir cold. Then leave the radiator cap loose and run engine at 1500 rpm until it warms up and the thermostat opens. Make sure heater is on full warm setting.

Oct 02, 2009 | 1991 Ford Ranger Supercab

1 Answer

1999 Ford Ranger air won't blow out of vents, defrost, or floor


SOUNDS AS THOUGH YOU HAVE A BLEND DOOR STUCK CLOSED IN YOU HEATER / AC SYSTEM SOMEWHERE. CHECK THE VACUUM MOTORS THAT OPERATE YOUR BLEND DOORS ON THE SYSTEM.

Dec 04, 2008 | 1999 Ford Ranger SuperCab

Not finding what you are looking for?
1997 Ford Ranger SuperCab Logo

Related Topics:

505 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...