Question about 1998 Ford Explorer
Go to the local library and sign out a repair manual for your vehicle or buy a manual at a local parts retailer. The diagram for timing is in the engine section of the manual.
Posted on Mar 11, 2009
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Mar 29, 2013 | 1999 Ford Explorer
Nov 17, 2012 | 1999 Ford Explorer
Nov 22, 2011 | 2002 Ford Explorer Sport Trac
Apr 29, 2011 | 2000 Ford Explorer
Get Ford timing tool kit, part = otc-6488 (For about $119 USD on eBay)
4 timing chains (3 front including the optional balance shaft chain + 1 back)
2 cam guides (1 front + 1 back)
2 oil tensioners (1 front + 1 back)
1 jackshaft tensioner (1 front)
1 jackshaft guide/cassette (1 front)
1 balance shaft tensioner (1 front) (will probably be ok, so dont replace it)
1 balance shaft guide (1 front) (will probably be ok, so dont replace it)
new sprockets + bolts + gaskets etc.
new spark plugs + throttle body cleaner + lithium grease spray + oil change
of these parts (the front stuff) can be obtained as a primary timing
chain rattle noise kit Part# = 2u3e-6d256-** ab for 4*4 & bb for
The kits also have later part numbers for us$ 76 @ http://www.fordpartsonline.com
My parts order (without the balance shaft stuff) was:
$76.04 KIT-TENSIONER TIMING 2u3e-6d256-ab
$47.93 Engine, Camshaft and timing, Timing chain, TIMING CHAIN, Explorer, Mountaineer, Rear - 4.0L SOHC - 4.0L SOHC
$57.36 Engine, Camshaft and timing, Chain guide, CHAIN GUIDE, Explorer, Mountaineer, Jackshaft To Cam - 4.0L SOHC - 4.0L SOHC
$103.22 Engine, Overhaul gasket set, OVERHAUL GASKET SET, Explorer, Mountaineer, Upper (Valve Grind) - 4.0L SOHC - 4.0L SOHC
$28.93 Engine, Camshaft and timing, Tensioner, TENSIONER, Explorer, Mountaineer, Upper - 4.0L SOHC - 4.0L SOHC
worth mentioning that this procedure is not enjoyable at all and
should be undertaken with at least 8 full days to completion (I recon
you could do it in half the time the second time).
It is basically on entire engine re-build with both heads off and the engine out of the vehicle.
is not possible to do the rear chain or sprocket with the engine in
the car as the flywheel needs to come off + at least 1 head, but it is
possible to do the front primary chain and or front cam chain with the
engine in the car.
will be a ford exploder and timing expert after you do this - the main
reason should be the love of your American built vehicle. Its a solid
car - except for the plastic guides!
Note: This is how i successfully did the job, but i am not a ford
mechanic and don't hold me responsible if this does not work for you.
Small Sprocket on the crank turns a larger (2 to 1 ratio) jackshaft
sprocket that is in turn connected front & back to the 2 camshafts.
Thus a 360o turn of the crank will turn both the camshafts 180o.
Firing order is 1-4 2-5 3-6, Right side numbers 1,2,3. Left Side = 4,5,6.
At TDC pistons 1 & 5 are fully raised, thus 1 is about to spark & 5 is evacuated.
engine will turn freely (no piston to valve contact) with the cams
180o out, it will even run (roughly) with 1 out 180o, any other
settings may cause major damage to the valves.
2 cam shafts come with timing markings, "yes" real timing marks that
anyone can use (even without special tools) to ensure correct timing.
The way to time it is to ensure both the off centre cam shaft slits are level/flat with the head.
the engine at TDC both the cams need to have the off centre slot in
the same position either up and level or down and level.
is super critical that both the camshafts are 100% in sink with each
other, i.e. not a few degrees off, the engine computer can compensate
for crank timing but not engineering failure.
warned the camshafts can turn easily fast & hard by themselves as a
few springs are compressed at TDC, I got my finger jammed and its
still healing + if the engine is not at TDC you may damage a valve.
heres the hard thing that you will need special tools for - if you
need to change the timing, you will need to be able to undo the cam
sprocket bolt on both cams & these are done up real tight.
is a tool that you attach that has 2 pencil thick shafts that fit into
the sprocket and prevent it from turning - then you need to put about
90Nm of force on the bolt (remember the rear one if LHT)
the $money$, its well worth getting yourself the tool kit - it will
save you hours in the long run. Search eBay for otc-6488 should be US
$119 - then sell them again for say $100.
is also a tool version of the oil tensioner in the kit that screws
right in and puts the correct amount of force on the chain + guide, to
enable you to do up the cam bolt with the chain and sprocket in the
right spot on the cam.
Dec 20, 2010 | 2003 Ford Explorer
Oct 28, 2010 | 1999 Ford Explorer
Dec 06, 2009 | 1998 Ford Explorer
Mar 04, 2009 | 2000 Ford Explorer
Feb 20, 2009 | 1997 Ford Explorer AWD
Apr 22, 2018 | 1998 Ford Explorer
233 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: