a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Remove the wiper arm by taking the nut off the end of the post coming through the base of the wiper. turn on the wipers and if the little post is turning back and forth with the other wiper, then you need a new wiper arm. the little serrations on the inside of the arm's base get stripped, usually from turning the wipers on when they are stuck to the windshield by ice. if the little post is not turning then you need a new wiper transmission. you will need a repair manual for that.
First remove the complete passenger side wiper check and make sure splines on wiper are not stripped. If this is not the problem It could be a linkage bar from the wiper motor to the wiper off or disconected. Since both wipers share the same motor if one works the other should. Check this by removing both wipers and then "Cawl" (little black piece between the hood and windshield underneath the wipers) Underneath the cawl you should be able to see the windshield wiper motor, and linkage bar to both of the wipers. See if the bar is disconected from the passenger side. If it is than reconnect it. These are the only two possible scenarios.
open the hood and at the base of the wiper arm is a little balck cap, remove this cap and under it is a nut. this nut holds the wiper arm tight onto a spline. check to see if the nut has backed off or needs to be tightened. if not remove the nut and take off the wipers, the black cowel (at the bottom of the windshield) is held on with three plugs.(one in the middle and one on each end.) and one large plug below the passanger wiper blade. the wiper assembly and motor is under this cowel.
hope this helps
The bolt that holds the wiper on is loose. There is a little plastic cap at the other end of the wiper arm, the side away from the wiper blade. Remove the cap and tighten the bolt. That should get it going again.
You can usually avoid that by using a good quality winter mix washer fluid that resists freezing, making sure the wipers are cleared of ice before beginning the drive and using the defroster to keep the windshield warm. In extreme conditions you just need to pull over and manually clean the ice off by hand.(only do that where it's safe). There are also specially designed wiper blades that will also help a bit.
hello, this sounds like your wiper transmission got out of alignment possibly due to ice on windsheild.don't really know.short of replacing you could loosen the nut under the cover and move wiper arm back possibly.
this could be a result of the linkage coming apart this is located under the cowel and not easy to service. It could also be a result of bad splines between the wiper arm adn wiper arm shaft. if the later is the case you can sometimes tighten the 15 mm nut that holds the arm to the shaft. but this will only work once or twice before the arm requires repolacement. remember folks, wipers are your friend in the winter, they are not ice chippers or snow plows, always clear your windshield with an ice scraper and make sure the wiper blades are not frozen to the glass. this small form of torture in the cold will save you big $$$ in the auto repair shops.
Check to see if the wiper motor moves the passenger side. If so, You may need to tighten the nut that connects the arm to the motor. Mine was stripped out because or snow & ice. So, I went to home depot and found a lock washer to fit.
Presto.... Nick from DE