Question about 1990 Isuzu Trooper

2 Answers

Check Engine light goes on and off

My Isuzu trooper is a V6 2.8L 1990 TBI Gas, Manual Transmission. The Check engine goes on after a few miniutes at idle speed. When the car is driven, the light turns off almost inmediately, The same thing happens when driving down a slope, when you don't have to use the gas pedal. Once you press the gas pedal, the light turns off. I read the computer codes and it indicates that the problem is with the oxygen sensor. I changed it for a new one, but the problem remains.

Thanks!

Posted by on

  • mausiba Mar 11, 2009

    Thank you, I will follow your advice. I will tell you later.

  • mausiba Mar 16, 2009

    I could not find the vacuum leak, but I know there is one because the idle speed is high (somewhere between 1000 and 1300 rpm), and while being at idle, if I press the breake pedal for a few seconds, the speed increases even more upon releasing the break. A few seconds later the speed returns to the initial value.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

My experience with these isuzu check engine light is that your air gas intake is not being properly regulated what you need to to change out or clean really good your kanooder valve and duflauge sensor. after those two things are taken care of reset your engine light by resetting your engine light relay or fuse.

Posted on Apr 23, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 67,757 Answers

Run a trouble code test to see what part is causing the check engine light to flash. I would lay my money on an O2 sensor.

Posted on Mar 10, 2009

  • yadayada
    yadayada Mar 10, 2009

    sorry did not read your entire post, check for intake manifold vacuum leaks with a can of carb spray (engine idle will change if u have one when the spray hits the leak), also check all vacuum hose's at engine, if u have a MAF sensor clean the inside with MAF cleaner, it is made by CRC. Get back to me if this doesn't clear the issue.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to replace a clutch on 1990 Isuzu trooper.


QOD: are you dead SURE the slave is ok? moves .75 to 1inch and OK?
2wd or 4wd? not stated.?
no engine stated? v6 or i4?


the procedure is same on all 4wd cars/trucks(mostly)
some pull the engine , for sure if engine needs work,as most do
after 25 years,
or pull transfer case and trans,pulled at the bell.
depends too,if you like spending long time under car
or on top, bent over fenders. (and tools)
if engine out no need to drain 1 or 2 gear boxes..and links,console..endless details....4wd lots more....

the video above shows the odd DUCK, throw out bearing.
and is important to know all that,
why not get a service manual..>?or use mitchell's????

not too many 1990 on the road.
rare car and year.
done many jeeps and rice 4wd.
2.6L,, SACHs 9.5" clutch $120 ($300 is bs)
or
2.8 v6 SACHs 9.125" clutch. $170

see they are not the same.....
I like Sachs, as you can see.. china clones not.

do you know how to fit the flywheel pilot bushing
and inspect fly surface, ?

the staging on the 9 bolt PP is here

im online now at one famous site
and the install skips, pilot bearing,funny that.
a real service manual is far better.



clutch-3xydvjc2hsdtpbulwfi331lq-2-0.jpg

26a-3xydvjc2hsdtpbulwfi331lq-2-1.jpg slave to fork lever to above damage, at T/o bearing
trans mission pilot shaft tip wrecked, or spline wrecked?
or you wiggle said shaft and front bearing in the box is SHOT.?
flywheel warped, or?
just saying, ive seen it all there, every fail.
on some all those were bad, on many 25year old cars.

Jan 13, 2017 | 1990 Isuzu Trooper

1 Answer

Have a 1990 isuzu trooper 6 cylinder throttle body need wire color codes to replace injector connectors


t
that is a very old car.this.

no you do mean it has 2 injectors, be nice to say "I have the 2 injector engine" a TBI injected engine .
its the 2.8L v6?

here it is, log in to mitchell's diy and read>?
first is 4 banger.

26297084-u1skeagojbjhu3ucj4o4k3kf-1-0.jpg the 6cylinder with 2 injectors TBI its called.
throttle body injected. so the blue/black wires are 12v power.
and the 2 injectors fire, blue and green. ISC valve on right.

26297084-u1skeagojbjhu3ucj4o4k3kf-1-1.jpg

Oct 01, 2016 | Isuzu Cars & Trucks

2 Answers

Transmission slipping and light is blinking


check the trans. fluid level. the procedure should be in your owners manual. if you cant find the procedure, a good default is to have it in neutral on a level surface with the parking brake on with the engine running. find the dipstick with "trans" or an icon of a gear on it. if it's low, add fluid. when you add fluid, add about a half a quart at a time. and after every time you add, get in, put your foot on the brake and shift back and forth from park to reverse to neutral, to drive a few times, slowly. if you're unsure of what type of fluid to use, ask the boys at the parts counter. if your fluid is not pink/clear red, you're in trouble. if it's brown, dirty, or has flakes in it, your trans is junk.

Feb 16, 2010 | 1990 Isuzu Trooper

3 Answers

Where is the diagnostic plug to get codes from check engine light


The 1990 Isuzu Trooper with a 2.8L GM engine, the diagnostic connector is located directly beneath the coin try in the front of your center console!!
Along with the typical OBD connector is two wires with a spade connector on each, one female and one male. Connect the two wires to display the diagnostic codes on your check engine lamp on the instrument cluster panel.
As for finding out your codes meanings, go to your nearest public library and locate a 1990 Trooper service manual.
 

Nov 24, 2009 | 1990 Isuzu Trooper

2 Answers

1990 Isuzu Trooper 2.8L V6 Fuel Delivery (Electrical Problem)


Inside the distributor and on the ignition module (7 pin) one of the wires to the camshaft pick-up had pushed out of the connector when I hooked up the new module. I reinserted the wire and problem was solved.

May 13, 2009 | 1990 Isuzu Trooper

1 Answer

Distributor cap compatability


your caps should be fine between a 90 and 91 one thing you should also check is that the kanooder valve on a 90 is different from one on the 91 these would not be compatable they redid the duflage sensor plug that goes from the kanooder valve to the wiring harness. you might need a kanooder valve mod kit these are really cheap you can grab one from checker for about 20 bucks well worth it trust me.

Apr 01, 2009 | 1990 Isuzu Trooper

1 Answer

Need a new Transmission assy.


GT4x4 are probably your best bet, or alternatively breakerlink or breakeryard (google for them)

Dec 24, 2008 | 2000 Isuzu Trooper

2 Answers

Need engine diagram for a 1990 trooper 2.8 v6


I would go to www. my isuzu parts.com
and view their index. It takes a little getting used to
but you can find oiut where a lot of stuff goes and how it connects.
Other than that go to a library and try to view a Haynes,Chilton
or Mitchell maintenance manual for more specific stuff.
If you go to my isuzu parts besure to notice the tabs at the top of each diagram --they will tell you if the diagram is for
a 4 cyl, a deisel or the v6.
good luck

Nov 20, 2008 | 1990 Isuzu Trooper

1 Answer

Idle speed too high


Look under the plastic intake tube for a hole

Nov 19, 2008 | 1990 Isuzu Trooper

Not finding what you are looking for?
1990 Isuzu Trooper Logo

527 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

67757 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22005 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...