Question about 2000 Chrysler Concorde

1 Answer

RPMS AND CHECK ENGINE LIGHT

I HAVE A 2000 CHRYSLER CONCORDE AND THE ENGINE LIGHT WILL COME ON- THEN ITS A LOUD KNOCK -AND THEN MY RMP'S WILL GO UP TO 3000 AND 4000 WHILE IM DRIVING SLOW NOT INCREASING MY SPEED. I CUT THE CAR OFF AND IT WILL DRIVE NORMAL. WHAT COULD THIS BE

Posted by on

  • tschantreia Mar 10, 2009

    thanks...thats sounds kind of expensive.. im going to have it put on a diagnostic machine this weekend..am i doing damage by driving it.

  • Anonymous Mar 15, 2014

    I have a 1995 Chrysler Concorde. It cranks and drives but it will start jerking and won't pick up speed. It doesn't overheat. After I let it sit for a while, it will drive just fine. What could the problem be?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

More than likely it could be a crank postion sensor but more than likely the tranny is slipping or having torque converter failure.

Posted on Mar 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chrysler concorde lxi 3.2l started with timing belt unaligned


Or worse, if it has bent valves, so yes do check compression. That is an interference engine design.

Mar 17, 2014 | 2000 Chrysler Concorde

1 Answer

Engine noise on chrysler concord 2000 2.7 v6 what is cause?


please be more specific describe the noise if possible post a video it could be anything from a noisy belt lifters ticking or a pulling going bad or worse a rod knocking

Jan 25, 2013 | Chrysler Concorde Cars & Trucks

1 Answer

2000 chrysler concorde check engine light came on, dash lighs flash and transmission wont shift any ideas?


It sounds like you have a problem with your security system if you mean that it won't allow you to shift out of park. BUT you should start off getting the engine error code read so you will know what the car is trying to tell you. Anytime you get a check engine light, the vehicle generates an error code.

Since you probably can't drive it, you need to rent, borrow or buy an OBDII scanner and get that code, so it gives you a clue on where to begin the troubleshooting process.

Jul 04, 2011 | 2000 Chrysler Concorde

1 Answer

I need to know: Which cylinder is the 4th cylinder on the 6 cylider Chrysler 2.7L DOHC 24 Valve engine?


Check this diagram for...
2000 Chrysler Concorde 2.7 liter DOHC V-6 VIN "U"
or
2000 Chrysler Concorde 2.7 liter DOHC V-6 VIN "V"
or
2000 Chrysler Concorde 2.7 liter DOHC V-6 VIN "R"

zjlimited_275.gif


Good luck (remember to rate and comment this answer).

Mar 28, 2011 | Chrysler Sebring Cars & Trucks

1 Answer

I have a 2000 chrysler concorde that the engine light just popped on - the error codes are po302, po420, po340


P0302-cylinder #2 misfire detected
P0420- catalyst efficiency below threshold bank 1
P0340-No cam signal at PCM.
The Cam sensor most likely needs to be replaced first. Clear the codes after that and drive and see what comes back on.

May 29, 2009 | 2000 Chrysler Concorde

1 Answer

I have a 2000 chrysler concorde with possible


I would say thats for you to decide. You got to weight all your options, whats the1300.00 for replacement engine? Or what, if it was up to me i would most likely get a nother car but thats me, you got to do whats best for you and your situation.

Feb 25, 2009 | 2000 Chrysler Concorde

1 Answer

Engine knocks 3.2 isuzu rodeo 2000 ? help


You don't say how many miles or give a service history, but, that said I would check the timing belt and tensioner. When tensioner goes bad is often is reported as a loud knock or tick. Usually most evident at low RPMs. Another low cost try is to use a can of seafoam in the oil now, run it a few miles, then change it for a high detergent, low viscousity oil and drive it a while to see if the lifters clean up. engine tick is very common, generally due to lifters oil passages getting sludged up a little for 2nd gen 3.2l's

Feb 18, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
2000 Chrysler Concorde Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...