Question about 1986 Volkswagen Golf

1 Answer

86 VW Camshaft Pulley

What is the easiest way to remove this?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 89 Answers

Check cam and engine markings. remove cambelt. open the tappet cover. remove shield. loosen cap bolts. take out pulley.

Posted on Mar 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tapping noise in 86 toyota tercel after replacing timing belt


timing belt idler pulley could be loose causing timing belt to slap.

Dec 20, 2012 | 1986 Toyota Tercel

1 Answer

How can i remove timing belt on 2005 kia sedona



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes

May 08, 2012 | 2005 Kia Sedona LX

1 Answer

Location and replacing a camshaft sensor on a 56 plate vw caddy 19d


Hi the sensor is on cambelt side,first you need to remove cambelt cover on the bottom of camshaft pulley nearest to front side the sensor will be there just hold by [1 or 2 screws] not sure it can just be replaced in place.hope this helps

Jul 22, 2011 | Volkswagen Eurovan Cars & Trucks

1 Answer

Hi, noticed a post of yours rear cambelt replacement on an a4 1.9 tdi ajm year 2000. Would be very grateful for any instructions. The car is stripped down ready for cambelt removing. Stuck on lining up...


Hi, I have pasted instructions below from autozone.com. The instructions call for the use of special tools. You can improvise with alternate tools, but please make sure your timing is right before closing the cover. Please let me know if you have questions, and thanks for using FixYa.

1.9L Diesel Engine
Some special tools are required to perform this procedure properly. A flat bar, VW tool 2065A is used to secure the camshaft in position. A pin, VW tool 2064 is used to fix the pump position while the timing belt is removed. The camshaft and pump work against spring pressure and will move out of position when the timing belt is removed. It is not difficult to find substitutes but do not remove the timing belt without these tools.

WARNING Do not turn the engine or camshaft with the timing belt removed. The pistons will contact the valves and cause internal engine damage.
  1. Disconnect the negative battery cable and remove the accessory drive belts, crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to Top Dead Center (TDC) of No. 1 piston. The mark on the camshaft sprocket should be aligned with the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the camshaft. The bar rests on the cylinder head to will hold the camshaft in position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner counterclockwise to relieve the tension on the timing belt. Slide the timing belt from the sprockets.

    jturcotte_1820.gif

    Fig. Use the VW tool to lock the camshaft at TDC for timing belt replacement-Volkswagen 1.9L Diesel engines


    jturcotte_1821.gif

    Fig. Locking the injection pump with the VW tool as shown-Volkswagen 1.9L Diesel engines


To install:
  1. Install the new timing belt and adjust the tension so the belt can be twisted 45 degrees at the halfway point between the camshaft and pump sprockets. Tighten the tensioner nut to 33 ft. lbs. (45 Nm).
  2. Remove the holding tools.
  3. Turn the engine 2 full revolutions to return to TDC for the No. 1 cylinder. Recheck belt tension and timing mark alignment, readjust as required.
  4. Install the belt cover and accessory drive belts.
    NOTE If the belt is too tight, there will be a growling noise that rises and falls with engine speed.

Jun 11, 2011 | Audi A4 Cars & Trucks

1 Answer

Need to know timing marks


REMOVAL
1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning (A/C) compressor drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark on timing belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt. Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.

INSTALLATION
1. Install tensioner pulley. Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
If existing timing belt is being reused, install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order.
6. Check that there is no looseness in belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
Do not add additional tension.
8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque:28~38 lb-ft (38~51 N·m, 3.9~5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on seal plate.
11. If they are not aligned, remove timing belt and start process from tensioner installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys. If deflection is not correct, repeat from tensioner installation.
Deflection pressure:22 Ib. (98 N, 10 kg)Deflection:0.39~0.50 in. (11~13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque:5.8~8.0 Ib-ft (7.9~10.7 N·m, 0.8~1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
15. Install water pump pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
16. Install generator belt and adjust the tension.
17. Install P/S and/or A/C drive belt and adjust the tension.
18. Connect negative battery cable.

INSPECTION
Never forcefully twist, turn inside out or bend timing belt. Do not allow oil or grease to come in contact with timing belt.
1. Replace timing belt if it is contaminated with oil or grease.
2. Check timing belt for uneven wear, fraying, peeling, cracking and hardening. Replace timing belt as necessary.
3. Bend timing belt into a "U" shape as shown in figure. Distance "A" must be at least 1.0 in (25 mm).
4. Inspect both idler pulley and tensioner pulley for uneven wear and smooth bearing operation.
5. Inspect camshaft pulleys and timing belt pulley for broken teeth or damage.
Replace any component that shows damage, excessive wear, or that appears prone to a possible failure.

Feb 26, 2011 | 2002 Kia Spectra

1 Answer

Diagram for volkwagon transporter 1997 2 litre 4 cylinder timing belt replacement


I found a 2.0L VW engine for a Cabrio. Not sure if this is the right one, but here goes:

REMOVAL & INSTALLATION

NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.

Gasoline Engines






Fig. 1: Adjusting the belt tension on a 2.0L 8 valve
91223g06.gif







Fig. 2: Remove the timing belt cover
91223p51.jpg







Fig. 3: Align the timing marks
91223p46.jpg







Fig. 4: Locate the tensioner
91223p47.jpg







Fig. 5: Loosen the tensioner bolt
91223p48.jpg







Fig. 6: Mark the belts direction of rotation
91223p52.jpg



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s).
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the distributor cap removed, the rotor should be pointing toward the
    No. 1 mark on the rim of the distributor housing. On 8 valve engines, the notch
    on the crankshaft pulley should align with the dot on the intermediate shaft
    sprocket.
  4. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt.
  5. Slide the timing belt from the sprockets.
    To install:

  6. Check the alignment of the timing marks. On 16 valve engines, the mark on
    the tooth should align with the mark on the rear belt cover.
  7. Install the new timing belt and tension the belt so it can be twisted 90°at
    the middle of it's longest section, between the camshaft and intermediate
    sprockets.
  8. Recheck the alignment of the timing marks and, if correct, turn the engine 2
    full revolutions to return to TDC of No. 1 piston. Recheck belt tension and
    timing marks. Readjust as required. Torque the tensioner nut to 33 ft. lbs. (45
    Nm).
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


Diesel Engines

Some special tools are required. A flat bar, VW tool no. 2065A, is used to
secure the camshaft in position. A pin, VW tool no. 2064, is used to fix the
pump position while the timing belt is removed. The camshaft and pump work
against spring pressure and will move out of position when the timing belt is
removed. It is not difficult to find substitutes but do not remove the timing
belt without these tools.
NOTE: Do not turn the engine or camshaft with the timing belt
removed. The pistons will contact the valves and cause internal engine damage.



  1. Disconnect the negative battery cable and remove the accessory drive belts,
    crankshaft pulley and the timing belt cover(s). Remove the camshaft cover and
    rubber plug at the back end of the camshaft.
  2. Temporarily reinstall the crankshaft pulley bolt and turn the crankshaft to
    TDC of No. 1 piston. The mark on the camshaft sprocket should be aligned with
    the mark on the inner timing belt cover or the edge of the cylinder head.
  3. With the engine at TDC, insert the bar into the slot at the back of the
    camshaft. The bar rests on the cylinder head to will hold the camshaft in
    position.
  4. Insert the pin into the injection pump drive sprocket to hold the pump in
    position.
  5. Loosen the locknut on the tensioner pulley and turn the tensioner
    counterclockwise to relieve the tension on the timing belt. Slide the timing
    belt from the sprockets.
    To install:

  6. Install the new timing belt and adjust the tension so the belt can be
    twisted 45 degrees at a point between the camshaft and pump sprockets. Torque
    the tensioner nut to 33 ft. (45 Nm).
  7. Remove the holding tools.
  8. Turn the engine 2 full revolutions to return to TDC of No. 1 piston. Recheck
    belt tension and timing mark alignment, readjust as required.
  9. Install the belt cover and accessory drive belts.
  10. If the belt is too tight, there will be a growling noise that rises and
    falls with engine speed.


prev.gif next.gif

Oct 29, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

How to install timing belt on 1998 vw beetle


Instructions
Things You'll Need: · Set of quarter-inch drive sockets Quarter-inch drive ratchet Set of half-inch drive sockets Half-inch drive air gun Set of metric wrenches Special tools for holding camshaft timing #2065-A and injection pump #2064

Step 1

Remove the accessory drive belts and the accessory drive belt tensioner. Remove the upper timing belt cover and the valve cover. Turn the crankshaft clockwise until the No.1 cylinder is atop, dead center, with the flywheel timing marks aligned.

Step 2

Install the special tool setting bar (#2065-A) on the rear of the camshaft. If it does not fit, turn the crankshaft once more and line up the timing marks again in the hole of the transmission housing.

Step 3

Insert locking pin #2064 into the injection pump to hold it in position. Remove the crankshaft pulley bolts, the crankshaft pulley and the lower timing belt cover. Loosen the tensioner pulley nut and allow the tensioner to move away from the belt. Loosely tighten the nut to hold the tensioner out of the way. Remove the top guide pulley and the timing belt.

Step 4

Make sure that the timing mark on the flywheel is lined up and that the camshaft setting bar and injection locking pin are in place. Loosen the camshaft bolt a half turn and tap the sprocket with a soft mallet to loosen it off its taper. The sprocket should move freely. Install the top guide pulley and torque to 18 foot pounds of torque.

Step 5

Install the new timing belt, starting on the right side and working counterclockwise. Keep the tension on the right nontensioned side. Loosen the tensioner pulley nut. Using the two-pin wrench, turn the tensioner pulley clockwise until the notch and raised mark are aligned. Torque the tensioner pulley nut to 15 foot pounds of torque. Make sure the flywheel timing mark is still aligned.

Step 6

Torque the camshaft bolt to 33 foot pounds of torque. Remove the locking pin from the injection pump and remove the camshaft setting bar. Turn the crankshaft two turns and check the alignment on the flywheel. Make sure that the setting bar can be inserted easily and that the injection pump locking pin can be inserted. Install all components in reverse order of removal and torque the crankshaft bolt to 18 foot pounds of torque.

My Recommendation - Pay an authorized VW mechanic $500 to replace the timing belt water pump an tensioner, and sleep better knowing that the job was done right. Just too many places for a novice car mechanic to screw up. jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); });

Oct 06, 2009 | 1998 Volkswagen Beetle

1 Answer

How to remove camshaft pulley


not sure what you mean by the tire, but you can loosen the tensioner and make some markings on where the belt and pulleys are. if you are very careful you dont have to loosen tensioner or move the belt. you could loosen the pulley, let it drop a little (taking care not to let the belt slip a tooth, and then put on the new pulley the same spot where the old one went. you might need some force to align the pulley to the cam, but this can be done.

Mar 11, 2009 | 1986 Volkswagen Golf

1 Answer

Timing specs for vw fox 1.8


Tune-up Specifications
Air/Fuel Ratio 0.7% Air/Fuel Ratio-Limits[1] 0.3 - 1.1% Timing[2] 6°+/- 1°BTDC Timing Advance[3] 30°+/- 3°BTDC Idle RPM[4] 800 +/- 50 [1] Check CO with the oxygen sensor connected. [2] AT 2300 RPM, and coolant temperature sensor disconnected. [3] Normal operating temperature, with coolant temp. sensor connected, at 2300 RPM. Add initial timing. [4] A/C off.
Timing mark is on flywheel, access hole is on top of bellhousing. Remove access plug with 27mm wrench if necessary
Firing Order is > 1342 Clockwise Rotation & #1 Plug Wire is at 2 Oclock on Distribitor Cap


Align the mark (can be a dot or notch) on the intermediate shaft sprocket with the notch in the crank pulley. Align the mark (can be a dot or notch) on the "Back" of camshaft sprocket with the top edge of the valve cover gasket. Be sure all the timing marks are properly aligned.

For further information refer to Timing Belt : Service and Repair
NOTE : The 8 valve engine requires a special wrench, Volkswagen No. US4493 or equivalent, to adjust the camshaft drive belt tensioner. Whenever the drive belt is removed and refitted, the camshaft and intermediate shaft timing MUST be adjusted. The drive belt can be replaced without removing the belt sprockets.
  1. Loosen alternator adjusting bolts and remove the fan belt.
  2. Remove the water pump pulley bolts and remove the pulley.
  3. Remove the upper timing cover bolts and remove the cover.
  4. Remove the timing belt guide, if equipped.
  5. Turn the engine by hand to set the No. 1 piston at Top Dead Center (TDC) and remove the crankshaft pulley.
  6. Remove bolt and nuts securing the lower timing cover and remove the cover. CAUTION: Turning the camshaft or crankshaft with the timing belt removed may cause damage to pistons and/or valves.
  7. Loosen timing belt tensioner locknut, release belt tension and remove belt from sprockets.
  8. Inspect belt for visible damage such as missing teeth or exposed threads. Inspect tensioner bearing for smooth running. Any damaged components should be replaced.
NOTE : On high mileage engines, failure of the tensioner bearing is a possibility. Consider replacing the bearing when replacing the timing belt.
  1. Align the mark (can be a dot or notch) on the intermediate shaft sprocket with the notch in the crank pulley. Align the mark (can be a dot or notch) on the "Back" of camshaft sprocket with the top edge of the valve cover gasket. Be sure all the timing marks are properly aligned.
  2. Temporarily install the crankshaft pulley to the crankshaft. Fit the timing belt starting with the crankshaft and intermediate shaft sprockets. Fit the belt so that it is as tight as possible between the crankshaft and the intermediate shaft sprockets and between the intermediate shaft and camshaft sprockets.
    1. Turn the belt tensioner clockwise to adjust the tension. The direction is important to avoid contact with the timing cover. Check the tension by twisting the belt as shown. You should be able to twist it no more than 90 degrees.
    2. Tighten the tensioner locknut to: 33 ft lbs (45 Nm)
    3. Rotate the crankshaft two revolutions and recheck the belt tension and the timing marks for proper alignment.
    NOTE: Very slight movement of sprockets and marks can be expected as belt tension is adjusted. Slight movement is OK. The smallest possible increment of adjustment is one whole tooth of the belt or sprocket.
    1. Remove the crankshaft pulley and refit the lower timing cover. Tighten the bolts to: 87 in lbs (10 Nm)
    2. Refit crankshaft pulley and tighten the bolts to: 15 ft lbs (20 Nm)
    3. Refit timing belt guide, if equipped.
    4. Refit upper timing cover and tighten bolt and nuts to: 87 in lbs (10 Nm)
    5. Refit water pump pulley and tighten the bolts to: 15 ft lbs (20 Nm)
    6. Refit fan belt and adjust tension. Tighten alternator adjusting bolts.

    Please Dont Forget To RATE ME !

Feb 09, 2009 | 1992 Volkswagen Fox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70365 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...